Search Documents

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018

By Lucia Vieira

Kelvin probe force microscopy (KPFM) can be used to monitor electrostatic charges on the surfaces of materials. In this paper, we describe the use of KPFM to evaluate the electrostatic effect induced by silver nanoparticles incorporated as clusters in diamond-like carbon (DLC) films, before and after scratching. The results are compared to those obtained for DLC films without silver nanoparticles. Raman spectroscopy was used to identify the DLC signature, and energy dispersive X-ray spectroscopy (EDX) was used to confirm the presence of silver in the film. The morphology of the DLC film containing silver was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings suggest that the incorporation of silver nanoparticles in amorphous materials could offer new options for electrostatic energy storage on the surfaces of these materials.

Jul 31, 2018

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By Elizaveta Cheremisina

In steelmaking process lime serves as flux. Rapid lime assimilation and slag formation of the desired composition have a significant effect on the refining reactions. It is important to know the rate limiting step of lime dissolution to control and improve the converter process. Kinetics of pure CaO and industrial lime dissolution in model slag has been studied in the range of temperatures 1300 –1600°C. Lime samples were prepared in cylinder form and immersed in the melt for predetermined time. Considering the total mass balance of CaO in the slag and linear dimensions of lime samples, mass transfer coefficients were derived. Diffusion coefficients were calculated under conditions of non-stationary diffusion. The derived activation energy of less than 200 kJ/mol indicates that diffusion is the limiting step in the process of lime-dissolution in slag.

Oct 30, 2017

By Marcelo Rebellato, Beatriz Pereda, Beatriz Lopez, Pello Uranga

The classical application of Nb microalloying in the development of thermomechanical processes for flat products has been related to its suitability to enhance strain-induced precipitation and get a pancaked austenite prior to transformation. As new steel grades or new lay-outs are being developed, more complex metallurgical conditions need to be evaluated. In this context, Nb microalloying, alone or combined with other microadditions, needs to intervene in a more controlled way in additional steps of the thermomechanical process, besides its conventional strain-induced precipitation role. For example, the hardenability enhancement associated with Nb to properly achieve lower temperature transformation products, demands a proper balance of the Nb amount precipitated during rolling and the one remaining in solid solution. Similar effects are also sought when the final available Nb is used to increase strength through precipitation hardening. This manuscript evaluates how changes in the rolling strategies affect the interaction between Nb(C,N) precipitation and austenite recrystallization at different steps of the rolling process. As the possible interactions between parameters intervening simultaneously are quite complex, the application of microstructural models helps to properly define the best austenite conditioning combined with the convenient amount of Nb in solution, as a function of the final property requirements. Along the manuscript, several strategies will be discussed for the case of hot rolling of flat products comparing both normal and coarse initial austenite grain sizes.

Oct 1, 2019

By Ramon Augusto Moretti, Henrique da Rocha Severino, Renato Nascimento de Castro, Fernando Cesar Sousa

Rolling stand 12 (LTx) of long steel, installed in the company A, Piracicaba - SP unit, had presented high levels of vibration, which affected its internal components, such as: shaft, gears and bearings, generating downtime. To evaluate this equipment a study was proposed by the following engineering techniques: Conventional Vibration Analysis, Operational Deflection Shape (ODS) and numerical simulation by the Finite Element Method (FEM). In the Conventional Vibration Analysis, high levels of vibration were observed during manufacturing process, especially when the material reaches the equipment. Impacts generate high values in acceleration, on average 80 m/s² peak to peak. In the moment of impact, misalignment of internal components was observed by ODS. Field results were correlated to those obtained by the Finite Element Method, which allowed to calibrate FEM model. Thus, the most effective structural modification already numerically evaluated was implemented in the system. Afterwards, new measurements by vibration and ODS techniques were performed, and attenuation of vibrational levels and operational mode, which overloaded the internal components rolling stand, were verified.

Oct 1, 2019

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Sihai Jiao, Xiaoming Xia, Bo Yan

Checkered plate, which is also known as floor plate, has a raised pattern that provides excellent skid resistance for a wide range of applications, such as flooring, walkways, platforms, stair treads, covers, etc. As one of most common products, carbon steel checkered plate is used in low strength with a large thickness margin for corrosion and costs a lot in corrosion resistance treatment and maintenance. Although austenitic stainless steel checkered plate meets the requirements of general corrosion resistance, it is also hard to provide a highly comprehensive performance for its low yield strength, which mean higher thickness, higher weight, lower stability of structure. Combined the advantages of stainless steel and carbon structural steel, a roll-bonded clad checkered plate with high performance in skid resistance, high strength and corrosion resistant is developed. The metallography shows metallurgically bonded interfaces. Both external and internal bending at room temperature can be done successfully done without any cracks. The yield strength is also significantly improved. Therefore, roll-bonded clad checkered plate is superior in microstructure, strength, ductility and workability. An application case on a pulverized coal injection platform in an iron-making plant, is also introduced to show the way of processing and installation. After two years of installation on the platform, the product still keeps the original appearance. It implies that the developed plate could keep the facilities functions with much less or no maintenance and make them much safer.

Oct 1, 2019

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By Claudio Pereira Diogo

A lot of galvalume/aluzinc steel sheet was furnished to a metallic roof manufacturer intended for tile fabrication. But, according with the roof manufacturer, that coils develops a different superficial aspect during processing. The purpose of this work was to provide an explanation for the appearance of the observed surface on one side of the coils. In order to find out the origin of the problem, mechanical and microstructural characterization tests were done at INSPEBRAS with the support of a partner laboratory. The results are described in this paper with their analysis and conclusions.

Aug 16, 2017

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018