Search Documents

By J Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration in small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using e-Dev™ electronic detonators in a typical mining application was conducted at Resolute’s Mt Wright operations in North Queensland in 2010. Results were based on direct comparisons to the current industry standard of non-electric firings as a baseline, with as many parameters as possible being captured during the trial. Development costs are typically high in most underground mines, especially in capital development headings, which are in waste and therefore of no direct economic value, so by being able to accurately fire to design, costs relating to both ground support requirements and volume of material removed, (and therefore haulage required) can be minimised. A direct comparison of overbreak (ground blasted outside of design) and cast (distance rock thrown from blast) was also made during the trial, as well as close monitoring of the drilling accuracy.

Mar 21, 2011

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By Stainier X.

The connexion between the Kent and the Continental coalfields on the one hand and the western British coalfields on the other has been for many years a controversial subject between geologists. These coalfields were once considered as detached portions of a former extensive sheet of Carboniferous deposits, but some geologists seem now to incline to the view that they were never connected. The writer hopes to show that the problem is one of the most difficult of geological investigations; that we are still far from a perfect solution; and that both of the extreme theories must be set aside. The physiography of NW Europe during the Carboniferous, with its various generations of earlier folds, is outlined and the features of the Lower and Upper Carboniferous anticlines and synclines discussed, followed by consideration of the denudation of the coalfields and local descriptions of the Malvernian range and Usk anticline, the Pennine chain, the Shropshire coalfield and the Kent coalfield. An attempt is made to trace the transverse Midland anticlines southwards and to deal with the intervening syncline: for example, if the dissymmetrical profile of the Pennine Chain holds good at its southern end then the syncline west of the chain must be deeper than the syncline east of it (the Kent syncline), and in this syncline the deepest part must be at its south-eastern corner, and therefore south of the diagonal ridge. T here is some actual evidence of the existence of Coal-Measures in this syncline, as the results of the Batsford and Burford borings prove. The hypothetical character of most of the conclusions will prove, beyond any doubt, how fa r geologists still are from a perfect settlement of this problem, and how much this settlement is dependent on the more or less advanced state of knowledge regarding all the geological features of these coalfields and of the surrounding country

Dec 1, 1916

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By Alfred Opengart

During any rush hour, tens of thousands of automobiles clog the main highways leading into or out of our large cities. Inevitably one or more cars stall or plow into another, causing a momentous traffic jam. Traffic backs up for miles as drivers try to maneuver around the roadblock. As commuters, we grin and bear the inconvenience, rationalizing the delay as part of the price one pays to live in a modern society. The truth of the matter is that the engineers planning the roads have the know-how to build adequate bypass alternatives into their design. The problem is one of economics -- can the cost of eliminating roadblocks be justified? Engineers designing solutions to complex materials handling problems for modem distribution centers are just now beginning to ask this question in relation to their work. Unfortunately in many instances, it has taken an expensive "traffic jam" to bring this question to the front. In these cases, a seemingly practical system promising an attractive return on investment -- using the latest equipment and computer controls -- was designed and installed. Everything went according to plan until one day a breakdown occurred. .Product flow stopped, and management realized it was at the mercy of the "machine." In such situations, management had assumed it could minimize the risks of the breakdown by injecting extra manpower to operate the system manually and pay the associated costs. What it had not recognized is that manual intervention is nearly impossible with sophisticated systems. Thus, too often -- and sometimes too late -- management found itself footing a very high bill for losses incurred because of major production stoppages and missed customer shipments.

Jan 1, 1973

By Brian W. Stump

Seismic networks provide the primary technology for monitoring compliance with a comprehensive test ban treaty. The design goal of the network is the identification of possible clandestine explosions detonated below the earth’s surface and possible in the oceans. Complementary technologies such as infrasonic, hydroaccoustic and radionucleide (particulates and noble gases) monitoring supplement the seismic monitoring covering explosions in the atmosphere and oceans. Seismic sources that will produce detectable signals will be both natural and man made in origin. Naturally occurring events include earthquakes, many of which are beneath the oceans or deeper than it is possible to drill, and volcanic eruptions. Accurate locations of such events to depths of beyond 10 km precludes consideration of these events further.

Jan 1, 1995

By S. T. Reese

STATISTICS of injuries in the quarrying and related industries in the United States first became available when the Bureau of Mines collected reports from the operating companies for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1952, is the 33d publication containing statistical data on injuries at quarries and related plants, and it is the first to be published since 1944. The last publication was Bulletin 458, Quarry Accidents in the United States during the Calendar Year 1942. The unpublished statistics for 1942-51 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries at quarries, but there is no Federal law that compels operators to supply such data, and the reports received from operators are voluntary responses to the Bureau's requests for information. Although the figures presented herein may not be complete for the entire industry, every effort has been exerted to make them so, and the figures given are believed to be thoroughly representative of the hazards to which quarry workers are exposed. Moreover, the figures are com¬parable as between States -which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or to comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1955

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

By Willard L. Hunter

The Bureau of Mines studied the effect of temperature upon the reduction of chromite by carbon and the relative reducibility of chromites as a function of their composition. Ferric oxide was also studied to provide comparative data. Pellets weighing approximately 1 gram and containing 70 percent ferric oxide, chromic oxide, or chromite and 30 percent graphite were subjected to closely controlled temperatures under a flow of argon for 15 minutes. The amount of CO and CO2 evolved was measured, and the reduced sample was analyzed by X-ray diffraction techniques. The reduction of Fe2O3 was studied over a temperature range of 600° to 1,400° C, while the reduction of Cr2O5 and chromite was conducted from 9000 to 1,621° C. The temperature above which appreciable reduction of Cr203 by graphite took place was 1,125° C. The temperature at which significant reduction started for three of the four chromite samples was approximately the same, indicating that there was concurrent reduction of iron and chromium oxides in the chromite mineral rather than selective reduction of iron oxides followed by reduction of chromic oxide. Rhodesian chromite appeared to dissociate at a lower temperature with concurrent reduction of iron. Based on the temperature at Which chromite was 50 percent reduced in 15 minutes, Transvaal chromite reduced most easily, followed by Mouat, then by Kampersian, and finally by Rhodesian DFC material. Statistical analysis of test results indicated that the ferric iron content of chromites affects their reduction behavior more than any other constituent.

Jan 1, 1966

By C. Caballero, K. Itagaki, P. Morales, A. Moyano, J. Font

Codelco-Chile is considering different processing options for the new projected concentrate from the Alejandro Hales mine. This concentrate is featured by its high arsenic content of up to 6%. Thus, it is important for Codelco Norte Smelter to define the technical feasibility for processing this high-arsenic bearing concentrate in its main smelting unit as it is the Teniente Converter, which beside of its dual feeding system can enhance the arsenic removal by volatilization. The present paper which is a part of an extensive research work will focus in the performed industrial scale test for processing about 7,000 tonnes of a high-arsenic bearing concentrates in the Teniente Converter at the processing rate of about 2,300 tpd. The impact on the chemical quality of the produced high grade matte will be discussed, and the effect of the As removal by increasing the Teniente Converter processing rate of concentrates up to 3,000 tpd when producing 70% Cu in the white metal will also be addressed.

Jan 1, 2007

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel frame- work buildings started toward the end of the last century. Progressively the requirements be- came more stringent, crushed bank slag, weighing 80 lb per cu ft as com- pared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft.

Jan 1, 1949

By Seyed Ahmad Jenabali-Jahromi

In this paper a meshless method called Finite Point Method (FPM) is developed to simulate the solidification process of continuously cast bloom steel in both primary and secondary cooling region. The method is based on the use of a weighted least-square interpolation procedure. A transverse slice of bloom as it moves with casting speed is considered as computational domain. The two dimensional heat transfer equation together with temperature dependent thermophysical properties is solved in the computational domain. The present work is verified in the mold region by the comparison of the surface temperature simulated by FPM and finite volume method (FVM) and also comparison of solidified shell thickness simulated by FPM and measured on a breakout bloom. For secondary cooling region the validation is done by comparison of the surface temperature simulated by FPM, FVM and thermovision measurements.

Jan 1, 2009

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023

By André Luiz Vasconcellos da Costa e Silva

O sistema ferro-oxigênio alumino tem sido investigado há muitos anos em função de sua importância para a indústria do aço. Uma grande fração de todo o aço plano produzido é de aço de baixo carbono acalmado ao alumínio, não apenas pelo baixo conteúdo de oxigênio residual em solução que pode ser obtido mas, também, pela importância do alumínio residual na formação de AlN, ferramenta importante no controle de estrutura e textura obtidas. O sistema Fe-O é relativamente bem compreendido e quantificado, da mesma forma que o sistema Fe-Al. Entretanto, há discrepâncias significativas na quantificação do comportamento do sistema Fe-Al-O havendo, ainda, bastante controvérsia com respeito a equilíbrios importantes. Assim, o objetivo deste trabalho é (a) realizar uma revisão crítica dos experimentos e avaliações termodinâmicas principalmente do equilíbrio Al-Fe-O–Al2O3 (b) avaliar os métodos atualmente usados para descrever este equilíbrio e (c) apresentar recomendações sobre os dados, com base em sua confiabilidade e consistência.

Aug 16, 2017

By S. Banisi, A. R. Hasankhoei, A. R. Ghasemi, E. Razi, G. A. Parsapour

At the pelletizing plant of the Gol-E-Gohar mining and industrial company two parallel dry closed grinding circuits, each with the average throughput of 300 t/h, are used. Each grinding circuit consists of a burner, a dry ball mill (6.2 m×13 m) and an air separator. The ball mill consists of a 2 m-long drying and an 11 m-long grinding chambers. The iron ore concentrate is fed to the drying chamber by a feed chute. The first 1.35 m of the drying chamber consists of 56 flights in two rows to decrease the feed moisture from 5% to below 0.2% and the rest of dryer chamber consists of deflectors to pass the material to the grinding chamber. It was found that when the feed moisture content increased from 1.3% to 3.5%, the throughput decreased by 12% (35 t/h) indicating a low performance of the dryer. Monitoring the wear rate of flights for a period of 12 months showed that the first 0.8 m length of the flights length did not experience any wear. This means that about 59% of flights do not contribute in material distribution and drying. A DEM simulation of feed chute and the drying chamber demonstrated that due to the inappropriate design of feed chute most of materials do not get in touch with the first 0.8 m length of the drying chamber. To overcome this problem, various feed chute designs with different geometries were simulated by the KMPCDEM© software. With the aim of arriving at a proper material trajectory, where the total length of the flights are used, a new feed chute was selected. The simulation results indicated that if the height of the flights is increased from 1.60 to 2.26 m and the slope is increased from 45 to 48 degrees the material arrive at the first 0.48 m of drying chamber. In this manner, the unused part of the drying chamber decreases from 59% to 36% of the length. After installation of the new feed chute, during a period of three months the throughput increased by 36 t/h.

Jan 1, 2018

By A. Kowalski

This paper presents methods of implementation and the added value that can be achieved by connecting personnel tracking systems and alarm-broadcasting systems. The authors point out the functions of the two systems that enable cooperation between them. Methods for connecting the systems on the surface and underground areas of mines require some intervention in both systems, so the authors point out a possible phased approach to introducing cooperation methods. Due to the fact that tracking systems in Polish mines are at an early stage of implementation, the article aims to provide new functionality, attempts to identify the needs of future users, and describes the experience of both production companies in terms of the development of cooperation methods.

Aug 1, 2013

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005