Search Documents

ignitions caused by cutting tools have occurred at a rate of some 14 per year in UK coal mines since 1965, mostly on the coalface. The rate has held steady despite reducing output and number of collieries. Investigations were carried out over this period into factors affecting both the concentration of firedamp in the cutting zone and the igniting source. A study into detecting and suppressing ignitions on shearers has been undertaken and it is feasible to prevent certain ignitions from spreading outside the cutting zone. Practical measures have been adopted by British Coal to identify frictional ignition sites and to lay down working procedures to minimise risk.

Jan 1, 1988

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

By William R. Yernberg

The combined 75th Annual Minnesota Section of SME meeting and 63rd Annual University of Minnesota Mining Symposium was held April 9 and 10, 2002, in Duluth, MN. This year’s theme was “Keys to the Future: Imagination, Innovation and Technology.” The meeting consisted of plenary and technical sessions and a special General Manager’s Session. The technical paper presentations included concurrent mining and mineral processing sessions. In the General Manager’s Session, representatives from the region’s taconite operations presented the current status, concerns and future plans for each of their operations.

Jan 1, 2002

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Ta M. Li, Russell A. Carter

The first century of mining in northern Idaho's Couer d'Alene District will soon he drawing to a close. Like so many other great raining districts, it has been a period accompanied by a rich and colorful history. From its early days as a gold rush camp, the district has evolved into the leading silver producer in the US, but the going has not been easy: early-day labor disputes, the challenge of mining for profit in some of the deepest mines in the Western hemisphere, and the constant search for new reserves at great depths have taken their toll of mines-and miners-along the way. To these traditional mining problems have of late been added the burden of inflationary cost increases, pollution control, and reclamation. A recent visit to the district by MINING ENGINEERING, how ever, revealed that the deep commitment of the operating companies and the quiet competence and vitality of their engineering personnel are key factors in the continued prosperity of the district.

Jan 7, 1976

"Real time analysis of conveyed bulk materials can be used to improve process performance by reducing variability and upgrading ore quality through selective removal of increments of flow that do not meet appropriate selection criteria. This paper focusses on proven Prompt Gamma Neutron Activation Analysis (PGNAA) and microwave transmission technologies used to representatively measure conveyed ore quality in real time so that meaningful decisions can be made between the mine and mill. This enables the effective removal by bulk diversion of small increments of conveyed flow such as waste, highly deleterious material or sub-economic material from the mill feed. Improved ore quality in plant feed optimises process performance, reduces processing costs and minimises tailings generation. Analysis is unaffected by particle size, dust, layering or segregation, mineralogy and belt speed. Technologies are explained and performance examples given from installations in copper and iron ore. The technology has been used successfully in bulk sorting for over twenty years typically using measured increments of a few minutes. Improvements in technology and calibration performance have resulted in accurate measurements over increments of thirty seconds and below.INTRODUCTION Ore quality variability exists on a number of scales. Block model grades represent a few hundred to many thousands of tonnes. Grade control at the mine occurs on a scale typically down to the size of a haul truck, which may be a few hundred tonnes. Highly variable ore quality is detrimental to process efficiency and effectiveness. Processing waste or low grade ore when higher quality feed is available represents a lost opportunity to generate higher revenues earlier in the operational life. Measuring ore quality accurately over short time increments during conveying enables small increments to be measured and diverted according to their quality. The paper explains the technology and benefits. Neutron irradiation techniques were considered potentially suitable for conveyed bauxite measurement by Beurton et al, 1995. Tran & Evans (2001) concluded there was no equivalent technology to Prompt Gamma Neutron Activation Analysis (PGNAA) in terms of material penetration power. PGNAA was evaluated by Nelson & Riddle (2003) for possible use in the phosphate industry and recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control. Cottle (2007) discussed test work for an iron sinter application and Delwig et al (2011) described the successful installation in 2009 and performance of PGNAA for base-to-acid ratio control in sinter feed with the analyser output used to control lime addition. Geoscan (PGNAA) works very well on iron ore and can “improve control over what is happening in the plant” and that comfort can be provided in knowing that the product is on-spec according to Minnett (2010). PGNAA is not yet used in the minerals sector for tariff purposes as has occurred since 2000 with Coalscan (PGNAA) in coal (Minnett, 2010)."

Jan 1, 2017

By G. Y. Liu

The structure-activity relationships for four thionocarbamate collectors are discussed in this pa-per. These collector classes are alkyl alkyl thionocarbamates, allyl alkyl thionocarbamates, acyl al-kyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates. The main emphasis will be to highlight the differences between collectors and their affinities for copper and iron sulfide minerals on the basis of data on electronic-structure properties obtained by vacuum and solution density functional calculations, flotation experiments and analysis measurements. The mechanism of interaction of these collectors with sulfide minerals is also discussed with perturbation theory. The theoretical study results indicate that acyl alkyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates have best performance in these agents as flotation collectors with improved collecting power for copper sulfide minerals and excellent selectivity against iron sulfide minerals, which are consistent with the experimental data reported in the literature.

Jan 1, 2014

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By John Kosek

The electrochemistry of carbon monoxide, nitric oxide and nitrogen dioxide was investigated at a variety of electrode materials in different supporting electrolytes. A portable detector for carbon monoxide was developed using a porous gold anode in perchloric acid supporting electrolyte. This detector has two full scale ranges, 0-100 ppm and 0-500 ppm. A portable detector for mixtures of nitric oxide and nitrogen dioxide was developed using a porous silver cathode in sulfuric acid supporting electrolyte. Nitrogen dioxide was determined in the gas stream by electroreduction. The nitric oxide in the gas stream was oxidized to nitrogen dioxide by passing it over Cr(VI) on firebrick. Electroreduction gave the sum of NO + N02. Analog circuitry was used to display the amounts of NO and N02 separately. Two ranges were available for each gas. They were 0-10 and 0-50 ppm for NO and 0-2 and 0-10 ppm for N02.

Jan 1, 1979

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

This report, the fourth in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more effectively extract and process mineral products. Environmental considerations, health and safety standards, price controls, inflation, material shortages, and more dependence on foreign imports were problems faced by the minerals industry. Although productivity increased for most mineral commodities, the annual rate of increase has slowed in recent years, indicating a maturing technological situation. Growing concern for energy resulted in increased interest and research in alternative fuel sources. The primary concerns of metallurgists were pollution control and improved efficiency and performance of metallurgical processes, especially for reduction of energy consumption.

Jan 1, 1974

By Richard I. Miller

Science Applications, Inc. has developed for the U.S. Bureau of Mines a rapid response radon monitor capable of accurately responding within three minutes to changing radon levels of magnitude from 100 to 10,000 pCi/1, typical of the levels in working uranium mines. The instrument weighs 17 pounds, is sized 12" x 10" x 6", and is capable of 8 hours of continuous portable operation with a self-contained, rechargeable battery power source. Residual chamber contamination from a radon level allowed to remain in the chamber for 90 minutes is about 10 percent, decaying about a factor of two in one hour. The instrument sensitivity is a nominal 0.1 cpm/(pCi/1), with a background count rate of less than 1 cpm.

Jan 1, 1979

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By R. F. Favreau, P. Favreau

Rock excavation is the first process in the cycle of operation of a mine, and efficient blasting is paramount to the profitability of the mine. The traditional way to design blasts has been by trial and error, based on the experience of the designer. This is probably the only important engineering practice which continues to be done without a precise engineering technique. The efficiency of most other mine processes has been improved by the use of high-tech, while a majority of blast design has not yet profited from the advantages of the computer. However, with the advent of the high-tech blast simulator Blaspa, it has become possible to design the parameters of the blast according to normal engineering practices. Over the last 50 years, the chemical and physical mechanisms which occur during a blast have come to be identified; they are reviewed in section B. Although these mechanisms are complex, they have nevertheless been expressed in terms of mathematical equations which have been assembled together in the computer to create the blast model Blaspa.

Jan 1, 2002

Future climate variability and change will impact on mining operations and their attendant communities. To minimise this impact, early and informed risk management is warranted. However, research into the risks posed by climate to the Australian mining industry has so far been limited. We are conducting a systematic study of the mining life-cycle to identify the main areas of vulnerability and adaptive capacity of operations and communities. This project aims to assess what adaptation activities are currently being undertaken within the mining industry and its communities across Australia and to develop a risk management approach that will aid the adaptation of practices in and around the industry, better assuring the security of people, jobs, revenue and the environment under changed or extreme climate conditions. The Canadian mining industry was recently assessed through a similar study, which found that many mining companies perceive a real risk to mining from climate change in the future, despite few companies being actively involved in managing such risk. At a workshop held by CSIRO involving mining specialists, the most vulnerable stage in the mining process in the Australian context was assessed to be production. In particular, impacts on water and energy supplies and also transport and infrastructure were of high concern. Additionally, heat stress on workers and equipment, changes in groundwater flow and increases in geohazards were also identified as important factors in the short and long term if problematic climate events become more extreme or more frequent. Risks in the planning and post-mine stages were also identified. Based on literature reviews and preliminary discussions with mining experts, here we present an initial assessment of the climate adaptation issues relating to mining and its associated communities and describe our future work plans in this area.

Jun 1, 2010

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By L. Newman, R. Wyrick, R. Berezowsky

The Stillwater Mining Company operates an integrated mines, mill, smelter and base metals refinery complex in Montana, USA for the production of a high-grade platinum group metals (PGM) bearing concentrate, nickel sulphate crystal and cathode copper from the PGM-containing nickel-copper converter matte. The complex was constructed in stages over several years, starting with the mine and the mill, followed by the smelter and finally, a base metals refinery, which was commissioned in 1996. Due to the relatively small quantity of matte production, a straightforward refinery process was initially selected to extract the base metals, which reported to a mixed nickel-copper solution for further treatment off-site, and yielded a high-grade PGM concentrate suitable for treatment in a PGM refinery elsewhere. Subsequently, as a result of increased matte production, the process was modified to separate the nickel and copper, and to produce a nickel sulphate salt and cathode copper. This paper describes the design and operation of the original and the modified processes utilized in the base metals refinery (BMR).

Jan 1, 2004