Search Documents

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By Christopher Newman, Robert Dupuy, David Newman

"The development of a multiple level underground mine is a complex task in which geology, engineering, ground control, and unit operations are integrated into a single mine design. The components are inter-dependent and must function cohesively to ensure a profitable underground mining operation. To optimize reserve recovery, mine planning should begin from the lowest level and progress up. This limits any misjudgments or oversights of a given level affecting the underlying levels and ensures the ability to maximize recovery from each level.Mine planning should start with the exploration and characterization of the geologic setting. Once the reserve geology and quality is well understood, then mine planning can begin with respect to the following:,Orientation of mine works with respect to horizontal stress,,Access to the reserve,,Determination of opening widths,,Selection of back, floor horizons and pillar centers,,Selection of development and secondary mining heights,,Appropriate interburden thicknesses, and,Examine the stability of the multiple level mine through numer¬ical modeling.The multiple level mine design process and decisions are presented through a case history example. The theme is that there is one opportunity to “get it right” as well as many chances to overlook a small aspect within the design that will plague the mine throughout all levels and through the entirety of its operating life.INTRODUCTIONAs surface quarries reach their economic stripping limit and encroach on mineral and/or reserve boundaries, they approach the end of surface mineable reserves. Furthermore, modern urban sprawl has placed previously remote surface quarries within suburban development and neighborhoods, leading to significant increases in noise, dust, and vibration grievances by the community and regulators (Newman, 2017). Many mining operations have begun year-round production of underground reserves to meet growing market demands. This does not permit the typical sequence of stripping overburden in the winter to provide limestone to mine during the construction season. Underground stone mining operations in the United States commonly utilize a room-and-pillar mine layout with drill-and-blast production methodology for the development of the reserve. Within the Midwest and Eastern regions, thick and flat-lying limestone formations lend themselves to the utilization of multiple level mining layouts. While a multiple level mine plan will increase the overall recovery of the reserve, greater overburden depths, multiple level geometry, and the presence of discontinuities all require an emphasis on ground control for the planning and development of a safe and productive multiple level underground stone operation."

Jan 1, 2019

By Michael C. Horn

The 61,470-acre Lick Creek Roadless Study Area is in the western Salmon River Mountains, centered 12 miles northeast from McCall, ID. U.S. Bureau of Mines personnel examined the roadless area in 1984. There is no recorded mineral production from the study area and no current mineral-related activity was observed. The roadless area is underlain by granitic rocks of the Idaho batholith. Pegmatite dikes and aplite dikes are present locally. Sampling indicates these rocks are not mineralized. No mineral resources were identified. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of federal lands recommended for wilderness, as required by The Wilderness Act of 1964. The USBM examines and evaluates individual mines, claims, prospects, and mineralized zones; USGS conducts broader geological, geochemical, and geophysical surveys. Such data helps Congress and other federal agencies make decisions affecting the use of public lands.

Jan 1, 1986

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By G Gilchrist, S C. Dominy, T Jashashvili, R C. A Minnitt

The grouping and segregation error is one of Gy’s seven errors that cannot be measured in any qualitative manner because of its transient and changing characteristics each time the sample is handled mechanically. Attempts to calculate the mean and variance of the segregation error is considered by some as ‘an exercise in futility’ that would not help us achieve representative sampling. This research is aimed at understanding the process of segregation of dense, finely divided and dilute particulate materials supported in a clean quartz substrate during intense agitation. Several mixtures of fine-grained materials including steel, tungsten carbide and gold grains were used in these experiments. Four hundred grains of each of the minerals and metals at a top size of 2 mm were mixed with approximately 600 g of finely ground quartz material (95 per cent passing 2000 microns) in a 500 ml plastic jar with a sealable lid. The mineral–?metal mixtures were analysed in three steps using microfocus X-ray computed tomography. Step one consisted of rolling the containers on a flat surface in an attempt to concentrate the mineral and metal grains in the core of the supporting substrate; this is a base case that can be reconstructed after each session of analysis. The second step involved gentle and vigorous shaking of the mixtures in order to segregate the denser minerals and metals from the supporting quartz substrate. In some cases, a third step involved splitting the sample through a riffle splitter. Three-?dimensional images of the surface of each grain, its volume and its X-, Y- and Z-coordinates, before and after intense agitation of the container, were interpreted from the reconstruction of the tomographic X-ray data. The spatial analysis of grains using cell declustering and 3D variography provided a useful means of characterising the distribution of the grains in space and the extent to which they had become segregated during the process of agitation. Spatial analysis indicates that in general, grouping and continuity of grains is weakly developed. The modelled nugget effect remains high for most tests, indicating that grains of similar size did not group together strongly. Agitation through rolling provided the best continuity, although not consistently in the long axis of the plastic jar. The nugget effect was consistently highest, and the range of continuity shortest in samples that had been split, indicating that the grouping and continuity were reduced through splitting the sample. Initial results indicate that very little segregation of the minerals and metals occurs in the quartz substrate. This is somewhat counter-intuitive, but suggests that the effects of agitation on mixtures of dense minerals and metals in substrates of lower density do not lead to excessive segregation. Differences in behaviour between dense materials in response to agitation are evident. Grains of different composition and shape did not group and segregate in a predictable manner in response to the agitation methods. Initial results indicate that the degree to which a material groups and segregates relates more to the characteristics of the denser material itself, rather than the agitation method employed.CITATION:Minnitt, R C A, Jashashvili, T, Gilchrist, G and Dominy, S C, 2017. Quantifying segregation of minerals and metals in particulate materials using computed X-ray tomography and variography, in Proceedings Eighth World Conference on Sampling and Blending , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

The 115-year history of the Hall-Heroult process for production of aluminium has been characterised by a sustained technology-driven improvement in costs and productivity. In the past decade the industry has effectively transferred best practice into older technology with improvements through computer control of the process, and redesign of cell linings using computer modelling . Incremental development is now at the point where diminishing returns will apply for further technical improvement effort however, until the gap between technical limits and current best practice is addressed through major process redesign. The process remains a long way short of its technical limits in energy consumption, carbon anode consumption, cell life and product purity. Investment cost in new capacity is very high, supporting the retention of older and less efficient technology and hence limiting the application of best practice in environmental performance and occupational health exposure. The industry is a major emitter of greenhouse gases yet the process has the potential to release oxygen as the primary waste. All of the above issues will be addressed in the new century, but only through commitment to the necessary long-term research and development that is required to achieve a redesign of the process.

Jan 1, 2000

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905

By Gene F. ] [Faufaul

This contract was concerned with the design, development, fabrication and testing of an improved tamper-proof filter cassette assembly for use in the, collection and evaluation of dust particulates, primarily in mining areas. This report presents the design effort, fabrication and tenting of five- prototypre unit$ as well as the design and production of 1000 filter cassettes with sampling heads. This new improved filter cassette has been tested and approved by NIOSH as meeting the requirements specified in the contract.

Jan 1, 1978

By José Raphael Olegário França

Separação eletrostática é o termo usado para todas as tecnologias de processamento que utilizam forças elétricas que atuam sobre partículas carregadas ou polarizadas sob um campo elétrico estático. O comportamento das partículas depende das suas propriedades elétricas, geométricos e tamanho das partículas. Portanto, a separação de espécies é possível se os parâmetros do campo elétrico e as propriedades elétricas diferentes das partículas são apropriados para o processo. No separador eletrostático de rotor as forças elétricas, combinadas com as forças gravitacionais e centrífugas agem sobre as partículas e são responsáveis pela separação mineral. No presente trabalho as forças eletrostáticas que agem no processo serão substituídas por um modelo de contato de coesão Hertz-Mindlin com JKR. O resultado apresentado, embora com limitações, conseguiu-se fazer uma boa estimativa do processo e alguns dos parâmetros do separador. Com a presente simulação é possível descrever o processo de separação além de permitir a redução de despesas de testes práticos, melhorar a compreensão das relações fundamentais, simular as influências dos diferentes parâmetros e por fim, estimar eventuais aumento de desempenho.

Aug 17, 2017

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By R. J. Kendall

As we enter the new millennium, the South African mining industry has to ensure that it becomes more competitive if it is to survive in the ever more demanding global environment. Traditionally, mechanization in narrow stopes has been limited to the use of scraper winches, and numerous mechanization attempts have been restricted to pilot projects operated on an extremely limited scale (with varying degrees of success). The benefits of hydropower are well documented, and Northam Platinum has shown these benefits to be achievable on a mine-wide basis. However, the equipment originally developed for hydropower systems has followed the traditional labour-intensive approach commonly used in deep level narrow stoping operations. The problems experienced with the hydropower system are discussed and the rationale for developing alternate technologies is explored. The hydropower system has shown to be a versatile powering medium which can be harnessed for a diversity of uses. It (hydropower) enables the mining engineer to change traditional paradigms and to design an entirely new approach for optimizing the mining operation based on explosive techniques. The system developed for Northam consists of the following: ?Purpose-built stope drill rig operated off the hydropower system with special features to ensure accurate drilling patterns throughout the length of the blast hole ?Purpose-built high rate cleaning system for rapid transfer of fractured ore to the stope orepass ?Redesigned stope layout to facilitate in-stope water control and to recover fines from the run-off water ?Purpose-built drill rig for rapid establishment of reef raises and advanced strike gullies ?Purpose-built drill rig for flat end development. On both types of development end rig, emphasis is placed on ensuring accurate drilling patterns throughout the length of the hole to maximize linear advance per blast. The paper discusses the implementation of the Northam system on a large scale as well as current initiatives to further improve on the efficiencies of mining operations. It concludes by emphasizing that mechanized hydropowered stope technologies are in their infancy and thus offer unlimited scope in progressing beyond today?s paradigms to present as yet unthought of solutions for optimizing deep level ore extraction.

Jan 1, 2000

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005