Search Documents

By K. Sugawara, Y. Hirakawa, A. Sato

The rock mass properties such as deformability and permeability are highly dependent on the existence of cracks. The Ratio of Crack Opening Dependency (RCOD) was proposed as a new index to evaluate the deformability of infinite jointed rock mass. The RCOD is defined as the ratio of total amount of crack opening and the total deformation of jointed rock mass. The theoretical relation between the RCOD and the effective compliance of jointed rock mass is discussed and confirmed through two-dimensional numerical analysis by the SC-DDM, together with the applicability to the rock engineering. Les propriétés de masse rocheuse telles que la déformabilité et la perméabilité sont très dépendantes de l'existence de fissures. Le rapport de dépendance d'ouverture des fissures a été proposé comme un nouvel index d'évaluation de la déformabilité de masse rocheuse à assemblage infini. Le rapport de dépendance d'ouverture des fissures est défini comme étant le pourcentage de quantité totale d'ouverture des fissures et de déformation totale de la masse rocheuse assemblée. Le rapport théorique entre le rapport de dépendance d'ouverture des fissures et la compliance efficace de masse rocheuse assemblée sont traités et confirmés au travers d'une analyse numérique à deux dimensions par SC-DDM en même temps que l'applicabilité à l'ingénierie des roches. Die Felsmasseneigenschaften wie Verformbarkeit und Durchlässigkeit sind hochgradig abhängig von dem Vorhandensein von Rissen. Das Verhältnis der Riss-Öffnungsabhängigkeit (RCOD) wurde als neuer Index der Verformbargkeit von infinit zerklüfteter Felsmasse vorgeschlagen. Der RCOD wird als Verhältnis der Gesamtmenge der Rissöffnungen und der Gesamtverformung der zerklüfteten Felsmasse definiert. Die theoretische Beziehung zwischen RCOD und der effektiven Verformbarkeit von zerklüfteter Felsmasse wird diskutiert und durch zweidimensionale numerische Analyse mit SC-DDM bestätigt, zusammen mit der Anwendbarkeit auf Bergbautechnik.

Jan 1, 2003

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By Maral Malekian, Pat Bellett, Eranda Tennakoon, Fernanda Carrea, Moe Momayez

Slope instabilities in open-pit mines pose a safety risk to workers and a financial burden on production. The direct impact of slope stability on safety and production makes slope failure predictions one of the important challenges in the mining industry. Predicting the precise time of slope failure has been the subject of much research in conjunction with the development of innovative monitoring technology designed to prevent sudden failures. This paper investigates the use of AutoRegressive Integrated Moving Average (ARIMA) model to predict the time of slope failure. Input data such as inverse velocity (IV) and dimensionless inverse velocity (DIV) from 20 slope failures were used to train the model predict the failure time. For comparison purposes, the time of slope failure using the traditional inverse velocity method is also provided. We show that ARIMA provides 90% more accurate predictions than the TIV approach.

Jul 12, 2023

By F. S. Karn

Conditions necessary to obtain optimum yield of useful products when coal is rapidly heated to extreme temperatures by laser irradiation were determined by the Bureau of Mines. Product distribution and yield were investigated as functions of several variables. Low-rank coals with high-volatile matter gave highest total gas yields. Medium-rank coals gave the highest yields of H2 and CA and low-rank coals gave highest yields of CO and C02. Macerals gave gases of approximately the same composition, but the total gas yield increased in the order fusinite, micrinite, vitrinite, and exinite. Total gas and C2H2 yields varied inversely with particle size. The addition of nominally inert gases such as Ar, He, N2 increased yields of H2, C2H2, and total gas. Metals such as nickel and platinum had little influence on the rate of coal decomposition. Total gas yield increased with total energy of irradiation, and the ratio of C2H2-CH4 increased with concentration of energy. A study was also made of the irradiation temperature, and a material balance was calculated.

Jan 1, 1970

By Dan Jackson

9:00 a.m., June 28, 1983 MR. MORTENSEN: Good morning ladies and gentlemen. Again, it gives me great pleasure to welcome you to another session of the 79th meeting of the Rocky Mountain Coal Mining Institute. The thing again that has always been impressive are the activities that we've had so far. The success in the meetings has been delightfully encouraging to all of our committee people. Please welcome the chairman of the session, Charlie Margolf. MR. MARGOLF: Thank you, Vernal. Good morning, ladies and gentlemen. It would be my privilege to serve as the session chairman this morning. To allow the maximum time for our speakers, I'll turn the microphone over to Bernie Bernstrom who will introduce our first speaker. MR. BERNSTROM: Thank you. As Vernal mentioned, Dan Jackson will be our first speaker. He is the Western Editor of Coal Age Magazine. Dan really doesn't need an introduction to this group. He's belonged to the Rocky Mountain Coal Mining Institute about 25 years. Dan is a native of West Virginia and he's an ex-coal miner. He graduated form West Virginia University as an electrical engineer and worked for Amherst and West Bending Coal prior to employment by Coal Age Magazine. Back in 1972 Coal Age moved him to Denver from New York City. MR. JACKSON: When Vernal Mortensen asked me speak to the members of the Rocky Mountain Coal Mining Institute earlier this year I found it impossible to say no to the guy because of what he has contributed to western coal. Little did 1 know that the subject he had in mind would be entitled, "An Outsider's View of Western Coal." At first I asked myself-I've been associated with the coal industry for some 38 years, 12 years in national operations and 26 years reporting on it. You might say that I've been married to two industries, coal and the business press for 26 years, but today I'll put on my business press hat and try to make an impression of what an outsider might think of western coal. But at the outset, let's get one thing straight: When you say press, whether it's business press, the media or whatever, and you heard some comments yesterday as far as what the media has done .to this industry and there's been some definitions bandied around as to just what an editor is. One of the most recent ones has defined an editor as a person who can talk on any subject with an open mouth. Now that's not my case. Secondly, I don't give long talks. Several years ago I was giving a rather lengthy talk to a group similar to this and it was halfway through the talk when I noticed one guy on my right looking at his watch quite frequently. I didn't mind that too much because all of us do that once in a while, but when he looked at his watch, took it off and shook it, I thought, "My God, better cut short." But for more than a decade western coal has enjoyed substantial annual increases in production from some 30,000,000 tons in 1970 to some 264,000,000 tons in 1981, but 1982 was a different story. We lost about 6,000,000 tons of production in that year. In 1983 it's expected to be a little worse than '82. Coal historically doesn't rebound from a recession as quickly as other industries. It takes about eight to 10 months longer for us to really get moving again and I'm afraid that you'll still have to don your fighting helmets and flack jackets when you go out into the market to sell your product. Western coal, as you know, has problems and al l of them are not going away when the recession ends and they won't go away overnight. I'm sure most of you are aware of what those problems are. Carl Bagge and Jim Harris, along with other speakers, at this meeting have educated us well on those problems and I'm sure you'll hear more from Jim Watt at today's luncheon. If everyone in this room were asked to list three orfourof the most serious problems facing western coal, I'd make book that the total of the answers wouldn't vary by more than 3 to 5%, if that much. But coal is not the only mining segment in the U.S. with problems. Metal and non-metal mining has its share, too. I'd like to step back into the past for a few minutes, if I may, to a time when our problems were just beginning. Since 1979 a third of the nation's mines, including coal, metal and nonmetal have been shut down. The total volume of all mining in the U.S. in that year totaled some $24 billion. Today that figure has dropped some 21 %. The after tax rate on return for mining companies has fallen from 6'/% in 1980 to minus 3% in 1983. But that's really not where our problems began. They began 20 years ago when a profound change began taking place in the U.S. economy. Our economy had been growing at about 2'/-3% annually without exception except for the great depression. Our inflation rate was about I'/%, interest rates were running about 6%, and the federal budget was $77 billion, really great figures compared to today. From 1960 to 1980 the federal budget increased almost 1.000% and taxed paid by individual families increased by 700% during that same period. Despite the huge increases in taxes, the federal deficit kept getting larger and larger year after year and within this 20 year period the national debt climbed to a trillion dollars. Economic progress of this type can't continue indefinitely without some serious consequences. The result of that economy, well, you know what happened and there is a direct relationship of that

Jan 1, 1983

By G Hancock, J Lowry, W D. Erskine, D Jones, T Coulthard, M J. Saynor, P Lu

An 8 ha trial landform was constructed in late 2009 at the Ranger Uranium Mine, located 250 km east of Darwin in the wet-dry monsoonal tropics of northern Australia. The objective of the trial, which comprises two surface cover types on a uniform two per cent slope, is to provide long-term data to guide the development by Energy Resources of Australia Ltd (ERA) of its landform closure strategy. The scope of the work program for the landform includes many aspects; however, this paper is focusing on run-off and erosion rates. The run-off and erosion rates are used to assess the long-term geomorphic stability by comparing measured with modelled export rates from a landform evolution model.Monitoring of wet season run-off is undertaken collaboratively by the Environmental Research Institute of the Supervising Scientist (ERISS) and ERA, on four purpose-instrumented 30 m by 30 m erosion plots. Continuous measurements are made in rectangular broad crested (RBC) flumes located at the outflow of each plot, of water level, turbidity (a surrogate for fine suspended sediment) and electrical conductivity (EC) (a surrogate for solutes). Each plot has a tipping bucket pluviometer located near the RBC flume. Bed load is collected monthly.This paper reports the findings of rainfall and bed load from the first two wet seasons (2009 - 2010 and 2010 - 2011) following construction. The field measured loads will be compared with the predictions made by the Cellular Automaton Evolutionary Slope and River (CAESAR) landform evolution model. Initial results indicate that predicted rates of sediment export from the CAESAR model are similar to measured export rates. This provides confidence in the capability of the model to predict stability of the future rehabilitated mine area, especially during the critical initial years following construction. CITATION:Saynor, M J, Lowry, J, Erskine, W D, Coulthard, T, Hancock, G, Jones, D and Lu, P, 2012. Assessing erosion and run-off performance of a trial rehabilitated mining landform, in Proceedings Life-of-Mine 2012 , pp 123-132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By Bao K. Le, Khang T. Truong, Masaki Kitazume, Toru Kobayshi, Long P. Le, Tanaka Hitoshi, Makoto Kamimura, Hoang-Hung Tran-Nguyen

"Earth levees constructed using dredged materials taken from a river along an earth levee have annually damaged in the Mekong Delta due to high void spacing in earth levees and floodwater. Sliding and internal erosion due to floodwater or piping are two key factors causing earth levees’ failures. This study proposed to apply Deep Mixing Method (DMM) to reinforce earth levees in the Mekong Delta, Vietnam. The DMM creates a soil cement wall or soilcrete wall having better engineering properties such as higher strength and low hydraulic conductivity than those of the in-situ soils. The DMM can be applied to reinforce earth levees with limit additional materials that provinces in the Mekong Delta are difficult to supply. The study investigates capacity of the DMM to reinforce earth levees in the Mekong Delta, Vietnam against annual floods. Seepage and slope stability analyses under various conditions were performed with various scenarios of earth levee’s body. The analysis results indicate that the DMM can create a wall that cuts off piping across earth levee significantly and can improve stability against deep sliding due to rapid drawdown of the floodwater.INTRODUCTIONThe Mekong Delta produces agriculture products of 50% of the whole country even though the Mekong Delta has an agriculture area of 30% of the country (Wikipedia 2014). Rice is the main product for the domestic demand and export. This is the main reason why the local people want to cultivate rice 3 times per year to increase the total rice product for export. To do that, the local provinces have constructed earth levees surrounding each area of 100-200-hectare against annual floods to protect rice fields, and farmers can grow rice in the whole year. There are thousands of kilometers long earth levees in the Mekong Delta, and the local governments have spent millions of US dollars to repair and to maintain their earth levees yearly (reports of Dong Thap province 2012; 2014).Earth levees in the Mekong Delta have often failed in flood seasons (e.g., from August to December), especially in Dong Thap and An Giang provinces – the two provinces confronting directly the annual floods from the Mekong River when the floods reach the Vietnam land. The main failure of earth levees is piping, and then causing collapse of some section of an earth levee. An earth levee was usually constructed by piling up dredged materials along a river with minimum compaction. Subsequently, floodwater flows through connected void spacing and washes out soil particles in the body of an earth levee slowly to create piping. Annual wet-dry cycles make the top clay layer swelling and shrinking to form cracks that can store rainwater to trigger sliding (whitlow 2001; Ton That Vinh 2003)."

Jan 1, 2015

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By Elaine R. Goetz

The eastern and southeastern regions of Ohio are part of Appalachian coal country, with a documented 1,300 miles of streams impacted by acid mine drainage. Since 1995, partnerships of local watershed groups, government agencies, private industries and universities have focused on the remediation of the affected waterways. The partnerships have spent $2.4 million annually in constructing and operating treatment systems such as wetlands, anoxic limestone drains, successive alkalinity production systems, steel slag leach beds, and lime dosers. These systems have been partially successful, and water quality has improved in the region, but no treatment has yet met the ultimate objectives of low cost, continual remediation. Our research group has investigated an alternative system for acid mine drainage treatment: electrolysis combined with pH adjustment to selectively precipitate recoverable, saleable metal products to offset the cost of treatment. We utilized a $0.2 million pilot facility constructed by the Wayne National Forest, in Nelsonville, Ohio, to process approximately 40 L/min of mine drainage from surrounding seeps. The pilot facility has multipurpose tanks that can be adapted to process acid mine drainage with different characteristics, such as high or low aluminum content or high or low carbonate concentrations. Sodium hydroxide was used for pH adjustment. Results indicate that saleable product can be generated with this treatment technology. In an initial, not optimized trial, one seep yielded 4.7 kg of dried 69 % iron oxide product from 10 hours of pilot facility operation, treating 23,000 L with electricity costs of $4.68. Dissolved iron concentrations in the water were reduced from 242 ± 18 mg/L to 2.8 ± 2.0 mg/L (99.0 % removal) while the initial acidity of 443 mg/L as CaCO3 was neutralized to an alkalinity of 160 mg/L as CaCO3. Iron oxide can be sold as pigment for an average of $1.47 per kg in the United States. Currently, approximately 80 % of all pigment used in the United States is imported, and there is incentive to purchase domestically recovered pigment. If the iron oxide from the pilot facility could be sold as pigment for $1.47 per kg, 43 % of the operating cost (raw materials, electricity and construction costs) of treatment could be offset by the sale of the product. Considering the cost offset, the electrolysis process shows potential as a sustainable low cost alternative for treating acid mine drainage.

Aug 1, 2013

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By A. V. Corlett

THE use of the diamond-drill hole as a means of breaking clown ore and waste is not new. Years ago, the method was adopted in mines in northern Ontario and in the western United States to reach out to bad pillars, or to remnants of ore left on walls, the winning of which by any other method might be dangerous or too expensive. The practice is still in vogue and has generally proved a success. Of the known mineral deposits in Canada and elsewhere, many are of very low grade. Some are marginal and not even worthy of being classed as 'ore' until some means is found and proved of exploiting them economically. Other conditions being favourable, if a mining method could be found that would give a large 'bulk break' with a sufficiently low cost of development and a low cast of mining per ton, mineral deposits of this latter type might be brought into the classification of ore. We know that any block-craving system whereby the ore may be undercut and allowed to crush and cave will give a very high breakage and low costs. In some cases, however, the physical characteristics of the ore do not lend themselves to this method. In such ore-bodies, the alternative system of 'bulk-breaking' might be aided by long diamond-drill blast holes. We could obtain this 'bulk breaking' by the use of long diamond-drill holes in conjunction with a sub-level system using extremely thick benches, or possibly by the adaption of modified open-pit methods to underground mining. ln fact, if conditions are favourable, the idea would be simply ta open up a slot or free face and break into it on a larger scale with longer holes. The use of deeper benches-that is, using each level as a sub-level and thereby eliminating much development footage, slashing, setting up, and mucking time-would naturally be expected to lead to cheaper mining.

Jan 1, 1940

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By B. K. Choi, S. H. Kang, G. E. Kim, K. B. Kim, S. Noh, T. K. Kim, H. J. Jin

Oxide dispersion strengthened (ODS) steel is being considered as an in-core structural material of future nuclear reactor systems because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperature in a ferritic/martensitic matrix. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. The primary activity is to develop high strength advanced ODS steel, fabrication technology for the structural components and key joining technology for the component fabrication. As a result, a Fe-10Cr-1Mo alloy with a superior creep resistance at high temperatures has been developed. An optimized fabrication process of this alloy system has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. Joining technology for the ODS steel components is also being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. These R&D activities will contribute to the realization of ODS materials for future nuclear reactor system applications.

Jan 1, 2015

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Jose L. Garcia

The following document aims to cover all issues concerning the three main methods employed for the in-situ survey of concrete pile integrity. Within it are described both sonic coring and low-strain tests and the frequency and time domain analysis of their results, which are the most advanced techniques currently in use in Spain. The survey techniques described were developed and began worldwide deployment in the 1960s, but it was not until the 1980s that they saw large scale implementation in Spain, largely thanks to the miniaturisation of electronics and computer equipment that made them easier to use on-site. Sonic coring, echo and frequency-response testing or mechanical impedance tests are spreading further every day. However, there appears to be a need for standardisation of the testing methods, as well as their implementation, interpretation and the presentation of results. The goal of these Spanish recommendations is to serve as a guideline for test standards and to provide examples for a correct and commonly agreed interpretation of test results, as well as settling any differences in the evaluation of defects detected in foundation works.

Jan 1, 2006