Search Documents

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

By Scott Orenstein

Construction blasting has allegedly been the cause of property damage in the following situations: (1) When the detonation of the shot hurls rock and debris into the air that causes property damage upon impact; and (2) When property owners notice cracks in their walls and foundations after they experience the momentary vibrations that coincide with the detonation of the shot. The current state of the law for both these situations is firmly established. Blasting is classified as an abnormally dangerous activity, for which the blaster is held strictly liable, whether the damage is the result of flying debris or vibrations and concussions generated by the blast. It is when the alleged blasting damage is supposedly from concussions and vibrations, however, that the courts usually reach the wrong result. The typical scenario involves property owners that thoroughly investigate their property after feeling blast generated vibrations, and find cracks that they believe did not exist beforehand. Most often the truth is that the property owners have never noticed these cracks before because they have never looked that closely before. Any structure has a certain number of cracks due to a variety of causes, such as settlement overtime and temperature and humidity changes.

Jan 1, 2004

Some crystal chemical properties of several apatites from Brazilian deposits and occurrences were determined; the samples had different origins (igneous, metamorphic and sedimentary). The aim was to establish relationships to their froth flotabilities behaviour. Detailed X-ray diffraction studies were carried out, to determine precisely the unit cell parameters and the degrees of crystallinity of the apatite samples. A thorough chemical analysis of these minerals was also conducted. Microflotation studies were carried out, using sodium oleate and dodecylammonium chloride as collectors. The crystallinity levels were determined for all samples studied, with the establishment of a crystallinity index, which varied from 10.0 to 4.5, on a normalised scale. A marked dependence was observed between this crystallinity sequence and flotability; for both collectors, flotability dropped drastically for crystallinity indices lower than 8.0. Also, the low crystallinity apatites showed a decrease in floatability, for longer conditioning times.

Jan 1, 1993

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By K Ionkov

The oolitic iron ore reserves in Lisakovsky, North Kazakhstan represent quite a challenging deposit both from a technological and from a resource point of view. The difficulties in processing such types of ore are connected with the extremely fine dissemination of phosphorus and gangue minerals inside the oolitic formations. The goethite crystals are cemented in their structure by aluminosilicates with quartz and other gangue minerals and dissemination is so fine that they are not separable by physical methods. The laboratory tests performed for dephosphorisation show that the combination of alkaline roasting followed by low intensity magnetic separation and acid leaching enables the obtaining of high grade iron concentrate. The magnetic separation performed ahead of leaching is effi cient as a means of buffering the high pH by washing out the soluble salts and the excess of base and after leaching facilitates the removal of secondary liberated gangue minerals in the non-magnetic fraction. As a consequence, phosphorous content is dropped to a more acceptable level for the ferrous metallurgy and iron grade and recovery reach 61.6 and 80.8 per cent respectively.

Jul 11, 2011

By B. A. Rogers

The problem of obtaining enough manganese for use in the manufacture of steel appears likely to recur when international relationships are disturbed and to become serious at any time when the United States is cut off from its customary supply. Some idea of the problems that an e under war conditions may be obtained from a description given by Ellicott3/ in 1918 before the American Iron and Steel Institute. This condition arises because in normal times there is an economic advantage in importing available high-grade foreign ores to the neglect of our own less satisfactory resources. That considerable low-grade manganese ore and a much smaller amount of high-grade material are available in this country is well known from geological surveys 4/ and has been confirmed by Bureau of Mines investigations. Locations of the various deposits are indicated in figure 1. The possibility of greatly expanding domestic production was actually demonstrated from 1913 to 1918, when the annual production of manganese from domestic ores rose from about 4 percent to approximately 35 percent 6/7/ of the total consumption of ferromanganese and spiegeleisen. In idea of how domestic production compares with total consumption in the United States can be obtained 1 from figure 2, taken from the Minerals Yearbook8/ for 1970. Assuming that it is possible to increase production of manganese ores sufficiently to supply all our needs, such a program presumably would require 2 or 3 years, and the cost of production would certainly rice considerably, for some time at least. For

Jan 1, 1941

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963

By J. C. Gerdeen

It is of upmost importance to keep the size of the program to a minimum for the computer being used. One way is to reduce the size of the data bank by adjusting the large common array A in the main program (page, line 32) and the statement following the assignment of A. The current value of A is 35001 and is optimized for the UNIVAC computer with 5,000 words of useable storage. Another way to reduce the required storage is to overlay the program. That is, to have in the computer only the subroutines which are being used. In large finite element codes, overlays or segmentation of the program is a necessity. The code presented here has three levels of segments and are presented graphically in the tree in Figure D-1.

Jan 1, 1976

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By Oyku Selimoglu

The key to successful mine production plan and subsequent operation is efficient mine layout design and optimization. Pit layout design and optimization allow the delineation and extraction of mineable reserves and the minimum waste subject to slope stability, economic, quality and quantity constraints. Many design and optimization software packages have been developed to aid this intensive and challenging process. These packages include VULCAN, SURPAC, DATAMINE, GEMCOM, MICROLYNX, MEDSYSTEM and MINESIGHT. These software packages are developed as integrated computer-aided systems used for database creation, survey, geological and geostatistical modeling, mine planning and production optimization and environmental modeling. In Turkey, many mining companies still plan and design mine layouts with traditional hand methods. In this study, VULCAN has been used to design and optimize the Eti-Bor A.S. Kestelek Boran Open Pit Mine in Western Turkey. The main objective is to show the company the superior advantages of mine planning software for designing and optimizing mine layouts over the traditional hand methods. Drill hole data used by the company to estimate the reserves for planning are used in this study. The ore grade varies between %1,04 B2O3 to %47,33 B2O3. The pit toe and crest strings are projected using variable batter angles and berm distances. On the north side, batter angle is 180 and berm distance is 25 meters, on the south side, batter angle is 320 and berm distance is 15 meters. In addition to that open pit bench height is 10 meter. The concepts of block modeling are applied to the Kestelek open pit mine with detailed ore grade modeling for each block. The Lerchs-Grossmann?s algorithm is used to optimize this mine based on the block model, the economic block values for each block and the underlying field constraints. The results from VULCAN were similar to the estimates by hand. The reserve estimates from VULCAN is 13,192,870 tons compared with the hand estimate of 13,200,000 tons, overburden estimates of 15,622,889 m3 compared with 15,000,000m3 obtained by hand with a stripping ratio 1.18:1 (m3:ton) from VULCAN versus 1.14:1 (m3:ton) from hand estimate. Vulcan improves the efficiency, speed and reproducibility of the planning results. It provides mining engineers, geologists and surveyors with a cost-effective modular system for assessing and planning the mine layouts. Furthermore, Vulcan?s specific modules allow efficient access and manipulation of databases, open pit mine design, block models, optimized 3D mine layouts, and more. However, for competitive business in Eastern Europe, VULCAN should improve its software support. Effective training, help desk support systems and nearby distributors with just-in-time solutions to company problems will generate competitive business for VULCAN.

May 1, 2007

By Louis Schaffer

The purposes of the research were to assess the applicability of new accident investigation methods to mining accidents, and to adapt those found to be applicable in the development of a new methodology for use in mining. The development included field testing, evaluation and modification of the new methodology. The report is in two volumes. Volume one discusses the background research, the design of a methodology for field evaluation, preliminary field tests in Utah mines, and work done to prepare for a formal, complete evaluation by federal government mine safety officials. This, volume 2, discusses the field evaluation done by the contractor and cooperating mines after the program was re-directed by the Bureau of Mines. It relates to research done during a period of approximately eighteen months, ending in April, 1983.

Jan 1, 1986

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1986. Shipments of processed tripoli increased slightly in quantity and 20% in value. Production of garnet, a common iron- aluminum-silicate mineral, decreased 12% in quantity and value. There was a 4% increase in the quantity and an 11% increase in the value of refined garnet shipped when compared with 1985 shipments, a new record high. Production of crude special silica stone decreased 7% in quantity and slightly in value, and shipments of finished special silica stone products decreased slightly in quantity and increased 229% in value. Production of emery, an impure aluminum oxide, increased 77% in quantity and increased 269% in value of product mined and shipped. [ ]

Jan 1, 1988

By M. Newton

Optimization and sensitivity analysis of mineable economic volumes have been standard practise for open pits for many years now, and more recently software has become available to apply techniques for delineating mineable reserves for underground mines. In general these techniques have been applied to a single resource model to quantify mineable tonnes and grade for underground mining. However by using multiple conditionally simulated models both the risk associated with the mining parameters and the risk associated with variations in grade, tonnes and profit can be quantified. Using suitable software the mine planner can then easily and quickly define and compare alternative designs to assess and improve the robustness of and the confidence in the final design.

Jan 1, 2007

By G. M. Rao, P. N. Deo

Graphite is soft and easily floatable but it is quite difficult to obtain high purity concentrate at coarse sizes. Chemical treatment can produce high grade concentrate but it is an expensive process. Graphite containing plus 96% fixed carbon (FC) with coarse flakes commands high price in international market. Such graphite concentrate containing plus 96% FC was produced in Indian Bureau of Mines (IBM) by using newly developed reagent (mixture of different hydrocarbons and terpenes, IBM/D7) instead of commonly used frothers viz. pine oil, MIBC, kerosine etc. and regrinding in a special type of mill with special grinding media instead of grinding in a conventional ball/ rod mill followed by cleaning. Both the new reagent (frother) and special grinding media are inexpensive and readily available. The process is under patenting. This paper focuses application of this new grinding methodology for flake size protection, and the new reagent for selective flotation of high purity graphite.

Jan 1, 1995

By M. Mikhaylenko

The most common methods of processing of uranium ores is sulfuric or carbonate leaching with conversion of hexavalent uranium to uranyl carbonate or sulfate anionic complexes followed by sorption of the later by strong base anion (SBA) exchange resins. It is known that chloride anion has high affinity for SBA resins so that it depresses sorption of anionic complexes of uranyl. Application of the SBA resins becomes impractical for recovery of uranium when chloride concentration in pregnant leach solution exceeds 3-5 g/l [1-3].

Jan 1, 2012

By J. Robert Wells

The Bureau of Mines has developed a spectrochemical procedure for determining 19 impurity elements in high-purity titanium metal, titanium oxides, and titanium halides in which all samples are converted to titanium dioxide. Determination of these impurities was studied in the general concentration range of 0 to 1,000 p.p.m., but different determination limits were found for the various elements. The procedure is quantitative for 18 elements but semi-quantitative3 for beryllium and has an overall relative standard deviation of 15.8 percent. Two mixtures were used, one composed of graphite and lithium carbonate plus gallium oxide and the other of graphite and lithium carbonate plus germanium dioxide. Each mixture was blended mechanically with an equal weight of titanium dioxide. Lithium carbonate served as buffer-diluent. Gallium was the internal standard for 1 impurity element, germanium for 7, and titanium for the remaining 11.

Jan 1, 1962

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983