Search Documents

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By T. T. Tigert

INTRODUCTION THE PURPOSE of this article on methane is to present the simple basic facts of the characteristics, detection, occurrence, and control of this natural gas in metal mines, so that operators and .safety men may deal with it with some degree of confidence. Fortunately, although methane has been noted at many metal mines throughout Canada, the occurrences usually are small flows of short duration, and the ignitions experienced have, in most cases, had minor consequences. However, methane does present a hazard that can be of serious proportions, and ?any complacent attitude toward this gas that might exist in the minds .of people engaged in underground mining operations should be dispelled when it is ,pointed out that, in Ontario alone, ignitions of this gas have resulted in at least four fatalities, and eight men seriously injured and burned, during the past three years. lt is well-known that liberation of methane can and does .occur suddenly, often in mines where no gas has been found before, and that many ignitions and explosions have occurred in so called non-gassy mines. In view of this, it is apparent that no mine can, with any degree of certainty, be classified as non-gassy. CHARACTERISTICS OF METHANIZ The characteristics of natural gas encountered in most of the Ontario mines indicate that methane is the chief constituent. Methane (CH4), commonly termed 'marsh gas', and by the coal miner 'firedamp', is a colourless, odourless, and non-poisonous gas considerably lighter than air, and is the explosive gas frequently found in coal mines. Its physiological effects, closely resemble those resulting from nitrogen.

Jan 1, 1951

By Bill Linville

During fiscal years 1967-68, the Bureau of Mines produced 185 technical papers and reports about petroleum and oil-shale research, which were published either by the Bureau or by others as referable scientific literature. Numerous other reports were prepared for Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau. Research performed during the reporting period by the Bureau on petroleum, natural gas, and oil shale was classified by 71 active projects. A basic appropriation of $3,575,000 was supplemented by $1,300,000 in fiscal year 1967, and that of $4,043,000 by $1,402,000 in fiscal year 1968, making the appropriated-to-supplemental fund ratios about 2.8 to 1 for fiscal year 1967 and 2.9 to 1 for fiscal year 1968. In fulfillment of the mission of the Bureau, through planned research programs, methods for producing and utilizing petroleum were improved. The continued conservation of this natural resource of petroleum, including crude oil, natural gas, and oil shale, was pursued through research performed by some 350 personnel at two petroleum research centers and two petroleum research laboratories supervised and supported by administrative personnel of the Bureau and the Department of the Interior.

Jan 1, 1970

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

By H. Sahay

This paper summarizes the history and ore-grade statistics of mining the Ming orebody, and then details the mining methods. Included are raising, stoping, drilling and blasting techniques. Particular attention is paid to ground support, ventilation and pumping requirements.

Jan 1, 1979

Simulator technology has advanced to the point where the cost of mining equipment simulators is beginning to make commercial sense. Simulator-based evaluation allows operators or potential employees to be assessed in a pseudo-real environment under surface and underground mining conditions. Simulator training also allows operators to be exposed to emergency and advanced situations such as brake or steering failure or a tireblowout. ThoroughTec, of South Africa, provides simulator equipment to the mining industry. The company’s various packages of simulator products provide an unbiased evaluation score that removes human error from the assessment process. This same evaluation score is also presented at the end of normal training or refresher training sessions. In this way, the simulator helps eliminate bad habits and improve efficiencies.

Jan 1, 2003

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019

By A. Ersoy, M. D. Waller

The principal factors which require consideration in predicting drilling rates are the bit-type, the bit operating parameters and the characteristics of the penetrated rock. A single index is not a sufficient basis for predicting performance. A variety of rock types were drilled in the laboratory with polycrystalline diamond compact (PDC) and impregnated diamond core bits using a fully instrumented drilling rig at different rotational speeds and with a range of weights on the bit. Quantitative determinations of a wide range of textural, mechanical and intact rock properties were also made. Multi-variable linear regression analysis was then used to develop predictive models of rates of penetration from the operating and rock property data. The models have been verified by statistical tests. The analysis indicated that the models for the pin and hybrid PDC bits have potential for practical application. However, although the model for the impregnated diamond bit appears to be reasonable from a purely statistical point of view, it may not be satisfactory for drilling uses as it is based on two measures of rock hardness alone. The application of multiple regression analysis to PDC drilling performance is novel and the technique shows promise for the prediction of rock drillability with PDC bits. The ability of the technique to provide a mathematical characterisation of the performance of new drill bits in specific rocks may prove to be of value to drill manufacturers and users

Aug 1, 1995

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By Lloyd L. Farnham

This paper is one of a series describing the mineral resources of the Nation, including location, history, production, ownership, geologic setting, and mining methods for most of the known manganese deposits in New Mexico, With few exceptions these descriptions are the result of field examinations by the writer. Of 32 counties, the 12 which occupy the western half of the State contain all the known manganese deposits, These counties are Catron, Dona Ana, Grant, Hidalgo, Luna, Rio Arriba, Sandoval, Santa Fe, Sierra, Socorro, San Juan, and Taos. (See fig. 1.)

Jan 1, 1961

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

By L Spencer, H Zwingmann, I Graham, D Cendon, B Kelly, D Burkett, F Lau, P Lennox

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kulumadau deposit represents an intermediate-sulfidation epithermal gold deposit (3.8 Mt at 2.3 g/t, Ag:Au = 1). Mineralisation is primarily confined to hydrothermal breccias within pre-existing fault zones, where it is disseminated throughout a hydrothermal matrix comprising chlorite-quartz-adularia-illite-I/S clays-calcite-pyrite. The host sequence represents numerous mid-Miocene pyroclastic flow eruptions within a tectonically active emergent shallow marine to subaerial depositional setting. Subsequent growth faulting was responsible for debris avalanches, which were subsequently cut by reverse faults. Faults were exploited by hydrothermal fluids, with the heightened porosity at the juncture between faults and debris material facilitating boiling of the ore constituents. Fluid inclusion studies suggest that fluid mixing between meteoric fluids and magmatic fluids, accompanied by boiling, were the primary mechanisms for gold deposition. The occurrence of anhydrite/gypsum as late-stage veins and their sulfur and oxygen isotopic values indicate post-mineralisation mixing of sea water with hydrothermal fluids.CITATION:Burkett, D, Graham, I, Spencer, L, Lennox, P, Cohen, D, Zwingmann, H, Lau, F, Kelly, B and Cendon, D, 2015. The Kulumadau epithermal breccia-hosted gold deposit, Woodlark Island, Papua New Guinea, in Proceedings PACRIM 2015 Congress, pp 205–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015