Search Documents

By J. J. deBarbadillo

This Bureau of Mines report describes a process for recovering chromium and other metals from superalloy scrap. Laboratory-scale experiments were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the fonnation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallurgical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and iron-molybdenum residue. Recovery of the principal elements contained in the scrap is chromium--93 percent, nickel--99 percent, cobalt--96 percent, and molybdenum--92 percent.

Jan 1, 1981

Map

Jan 1, 1941

By Mulligan John J.

The Bureau of Mines investigated lode tin deposits on Potato Mountain, Seward Peninsula, Alaska. Tin was found to occur as cassiterite associated with quartz, tourmaline, pyrite, arsenopyrite, and earthy clays, but the deposits lack the varied accessory minerals commonly found in tin districts. The tin-bearing deposits are in metasediments along minor breaks and bedding planes but not in the crushed earthy filling of major faults. Cassiterite and sulfides occur with quartz in veins, both with and without earthy clays, and disseminated through tourmalinized wall rocks. The deposits are characterized by irregular segregations containing 1 to 10 percent tin within zones averaging not over 0.25 percent tin. The largest segregation exposed is on the summit of a low hill on the east-central slopes of Little Potato Mountain; most of the outcroppings are in an area trending east to west, roughly 10 to 30 feet wide and 300 feet long. Sample values ranged as high as 12 percent tin, but the average grade may be about 1 percent tin. The extreme irregularity of both grade and composition precludes a more exact determination. Similar concentrations are scattered for over 1,000 feet to the west and north, but these are smaller and lower in grade. Elsewhere on Potato Mountain, generally similar deposits occur as clusters of veinlets at widely separated points in the metasedimentary walls of major faults.

Jan 1, 1965

By A. D. Prokop, J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated long-wall test facility located at the Pittsburgh Research Center. Sound levels were recorded every 1.5 m [5 fl] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 MA attenuation was attained upwind of the headgate drum.

Feb 24, 1997

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By W. Lin, M. J. McPherson

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Feb 24, 1997

By R. L. Grant

The principal official test performed by the Bureau of Mines to determine the permissibility of coal-mine explosives, commonly referred to as the gallery test, has been in use at the Bruceton station for many years (2, 16).4/ In this test the explosive under study is loaded into the borehole of a steel cannon and fired into a flammable mixture of natural gas and air or natural gas, air, and coal dust. To meet the requirements for permissibility, the explosive must not ignite the gas mixture under the conditions of the test. There is little doubt that these tests have succeeded in the main objective, namely, to screen the relatively safe from the relatively hazardous explosives. It has been generally conceded that adoption of permissible explosives by the coal-mining industry in the United States has substantially reduced the frequency of disastrous underground explosions caused by blasting. In recent years, however, research workers planning programs for improving the safety of coal-mine explosives have felt the growing need of a more quantitative method for measuring the incendivity of explosives based on a better understanding of the role of the important variables in the gallery tests, Accordingly, it was decided to apply certain statistical methods and techniques to the gallery test to develop it into a more precise tool for evaluating permissible explosives. One of the first and more important methods applied for this purpose was the up-and-down technique (6,7,17), It was demonstrated (14,15) that the weight of the explosive charge directly affects the ignition probability of the natural gas-air atmosphere and that the curve of ignition probability versus charge weight is a cumulative normal curve. Following these experiments, a program, still in progress, was set up to study how the addition of sodium chloride to various permissible-type ex-plosives affects their incendivity. This program resulted in 3,294 shots,

Jan 1, 1961

By J. H. Jacobs

In late 1946, research was begun at the Bureau of Mines Electrometallurgical Laboratory at Boulder City, Nev., to determine the possibility of electrowinning manganese from chloride electrolytes on a continuous basis. All phases of electrodeposition were investigated on a small scale it the laboratory, and the results were reported by Jacobs and Churchward. These results indicated that a chloride process had certain possible advantages over the sulfate process that made it worthwhile to continue the investigation on a semi-pilot-plant basis, and this paper reports the results of this work. Research and development work on a process for electrowinning manganese from low-grade ores has been carried on intermittently by the Bureau of Mines since 1936. A process was developed, using sulfate electrolyte, that has been extensively described in the literature.

Jan 1, 1951

By G. W. Grove

The wearing of self-contained oxygen breathing apparatus, although relatively safe if proper precautions are taken, is dangerous if defective apparatus -is worn, if men with inadequate training, experience, and physical requirements are used, or if improper procedure is followed. This is proved by the fact that at least 26 men are known to have lost their lives while wearing-oxygen breathing apparatus since its introduction in this country about 35 years ago. Self-contained oxygen breathing apparatus, commonly called "mine rescue apparatus" and sometimes improperly referred to as "oxygen helmets," is the only equipment that can be used for respiratory protection against poisonous mine gases, regardless of concentration or against an atmosphere containing little or no oxygen.3/ Apparatus of this type was introduced in this country in 1907, and since that time it has been widely used in conducting rescue and recovery work after mine fires and explosions and in some other work. All oxygen breathing apparatus used in this country before 1918 was imported from Europe, and although this equipment provided safer, more rapid means of conducting recovery work after mine disasters, there were many mechanical deficiencies in the apparatus which resulted in the death of some of the wearers. This led to the research and experimental work by the Bureau of Mines that resulted in the development and manufacture of more reliable and efficient types of apparatus in this country.

Jan 1, 1944

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By M J. Shearer

An investigation into the reliability of the data being collected at the Mount Isa Mines site operated by Glencore in Queensland allowed on-site ventilation personnel to scrutinise pressure and volume measurements collected from the primary surface fans. The investigation effectively identified discrepancies being reported to the on-site remote monitoring system. The difference between the real-time and static measurements on the P63 RAR shaft identified that the in situ differential pressure transducer and piezo annubar system was not operating correctly. This indicated a deficiency of approximately 30 per cent reporting back to the remote monitoring software versus the live readings measured with the Pitot tube bomb and ALNOR AXD610 pressure micro-manometer.Constant monitoring of an operations ventilation network is imperative to ensuring that the underground atmosphere provides a safe and healthy workplace. Further benefits to real-time monitoring allows for the early indication of network failures and promotes increased availability. An innovative approach to out engineer and improve the existing measuring equipment from the 1970s was sought.The use of ultrasonics in the mining industry is not new with ventilation management systems (VMS) equipment available within the marketplace. The introduction and implementation of a reliable product for real-time monitoring was a challenge to overcome due to limited access and suitable measuring points within the mine. The available equipment on the market through mainstream suppliers was not suitable for the unique application required due to the in situ installation of the surface fans. A solution was identified in the oil and gas industry through collaboration and innovative thinking. This paper describes the sustainable approach to implement a reliable air flow monitoring system on-site.CITATION:Shearer, M J, 2017. Case study – an analysis of reliability and efficiency: ultrasonic versus annubar technologies, in Proceedings Australian Mine Vent Conference 2017, pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By I. Mc Dougall

Finite element models were generated of two submerged arc furnaces of different geometries. A 48MW circular furnace and a 68MW 6-in-line rectangular furnace were studied. The electrodes, raw material, slag and molten metal were included in the model. ANSYS/Multiphysics was used to predict the current density distribution in the electrodes, raw material, slag and molten metal as a result of the three phase AC current. The effect of the electrode immersion on the current path was studied. The ?proximity effect? caused a pronounced asymmetry in the electrode currents in the circular furnace, whilst the electrode currents in the rectangular furnace exhibited radial symmetry. The current distribution in the melt in both furnaces indicated that the bulk of the current flows between phases. The current density is greatest between electrodes. Results were compared to qualitatively similar published work, operating experience and results of furnace dig-outs.

Jan 1, 2007

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By P M. Ashley, M Muller

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of north-eastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe land sliding in previously mined areas. Mining from the 1890s to the 1960s has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969