Search Documents

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

By E. L. Garton

The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying southwest of the Arbuckle Mountains. It includes six counties: Cater, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvanian age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.

Jan 1, 1941

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By Orris C. Herfindahl

Every few years we are treated to a battle over trade policy when the Reciprocal Trade Agreements Act comes up for consideration. In 1962 it is especially appropriate to consider the problem of mineral import -policy and the closely related problem of general import policy, for this year's struggle is different from those of the past in two ways. First, proposals have been made which are a substantial departure from past trade agreements legislation, and second, the formation and growth of the Europe Economic is Community may have an important bearing on the kind of legislation that is adopted. But this anticipates what is to come later. My task is to examine the problem of mineral import policy, although we shall find soon enough that general trade policy must be considered in order to get an indication of what is in store for minerals.

Jan 1, 1962

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves - pressure losses as negative values and energy additions as positive values-and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Feb 24, 1997

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By Bill York-Feirn

The Colorado Mine Safety & Training Program (MSTP), in late 2005, completed and began distributing two new training tools; one geared to underground coal mine foremen and the other to surface aggregate employees. Through strong partnerships with MSHA, Colorado Coal Mine Board of Examiners, Colorado Mining Association and the Colorado Rock Products Association, the MSTP continues to create innovative and interactive training tools for not only Colorado, but for the national mining community. "Although we shoot and produce these materials in Colorado, it's important to us to make sure they are useful nationally," said Bill York-Feirn, MS TP Manager. The interactive DVD program "Underground Mine Foreman Certification Study Guide (Coal)," was completed in October 2005. It won the 2005 Grand Prize at the MSHA National Training Materials Competition in Beaver, West Virginia. [ ] This program is fully based upon the requirements of Title 30 Code of Federal Regulations (30 CFR) Parts 48, 50, 70 and 75 for underground coal mine foremen. It contains eight modules plus immediate access to relevant laws in the appendix. Topics covered include: Federal Law, Practical Math Skills, Mine Gases, Ventilation Maps, and scenarios addressing a variety of practical mining concerns. The DVD is designed for self-¬paced study and practice.

Jan 1, 2006

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

By J. K. Afidenyo, J. Osei-Owusu

"The Obuasi Mine of AngloGold Ashanti Limited has been operating the world’s largest Biooxidation Plant at its Sulfide Treatment Plant (STP) in Ghana, using the Gencor Biox® technology since February 1994. The Biox® technology was preferred to other alternative methods of treating refractory sulfide ores such as roasting, pressure oxidation and nitric acid leaching due to among other reasons, its lower capital and operating costs, reduced technical risk, relatively benign environmental impact and its ease of operation and maintenance in a remote location.STP has since commissioning succeeded in operating this technology successfully but not without some operational problems. The Plant has seen a number of upgrades and modifications in its circuits which were motivated by cost, operational and throughput constraints.The objective of this paper is therefore to highlight the mine’s experience in the treatment of its complex carbonaceous refractory sulfide gold ores with emphasis on plant operations and improvements such as the Biox® reactors expansion, flotation concentrate upgrade project and neutralization circuit modifications. The Biox® Plant operating cost is also discussed.INTRODUCTIONThe Obuasi mine forms part of the AngloGold Ashanti Group of Gold Mines. It is located in the Adansi West District of the Republic of Ghana. The mine is primarily an underground operation, although some surface mining still takes place. Ore is processed by two main treatment plants: the Sulfide Treatment Plant (for underground ore) and the Tailings plant (for tailings reclamation operations). A third plant, the Oxide Plant, is used to batch-treat remnant opencast ore and stockpiles, of which there are adequate tonnages to keep the plant operational until 2008.Though reference is made in this paper to the Tailings and Oxide Treatment Plants, the main focus will be on the Sulfide Treatment Plant."

Jan 1, 2008

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

Trends in Test Filtration to Respond to Decreasing Sample Size There has been a steady decline in the quantity of samples available for testwork when developing new mining processes due to the maturing mining technology and the increasing costs of pilot testing. Larox, a supplier of filtration equipment and its co-operation partner Lappeenranta University of Technology (LUT) have been actively developing new equipment, testing methodologies and tools to plan test campaigns with the objective of being able to determine the optimum filtration technology and the parameters for sizing full scale equipment with a minimum sample size. With smaller sample sizes, the test scale diminishes from pilot scale to bench scale, and the small equipment size has implications for scale-up. Redesigning the equipment to simulate full scale equipment rather than to match filtration theory has led to some interesting developments. Comparisons between bench scale equipment and production units help identify the limitations of bench scale testing. The nature of filtration is such that it is unreliable to estimate filterability theoretically, and different testing methodologies have been investigated to be able to test the feasibility of filtration from samples as small as few grams. While not optimising the filtration technology, these methodologies provide an adequate level of accuracy for scoping studies. Together with improvements in equipment, a software tool has been developed to reduce the number of tests necessary to optimise filtration technology and parameters for sizing.

Sep 13, 2010

By R L. Brathwaite

The epithermal gold-silver deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Epithermal deposits consist of quartz veins, quartz vein stockworks and hydrothermal breccias that are mainly hosted in subaerial andesitic or rhyolitic rocks of Tertiary age. The deposits were formed at depths of typically less than 1 km and at temperatures between 180¦ and 320¦C, although ore grade mineralisation was generally deposited at less than 270¦C.   In New Zealand, epithermal deposits occur in association with late Cenozoic volcanic rocks in the Northland, Coromandel and Taupo volcanic regions. All of the past and present gold production, estimated at greater than 380 t (along with 1300 t Ag) comes from the Miocene-Pliocene Coromandel Volcanic Zone, where about 50 epithermal gold-silver deposits occur over a 200 km long belt. In Northland, silver and mercury have been produced from hot spring type epithermal deposits, and several gold-silver prospects have been identified. Ore grade gold-silver mineralisation is currently being deposited in several active geothermal fields of the Taupo Volcanic Zone, and extinct geothermal systems occur on the western side of the zone. The active systems have provided natural laboratories to help understand the processes of epithermal mineralisation.

Jan 1, 2005

By X Yang, B Wang, L Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Huoqiu iron ore field in north-west Anhui province is located in the south-east margin of the North China Craton and hosts large iron resources. Orebodies are hosted in Neoarchean amphibolite facies metamorphic rocks, forming silicon-iron bands from north to south. The area is dominated by an Early Precambrian basement consisting of Neoarchean grey gneisses, amphibolites and metasediments. The gneisses are similar with assemblages of Trondhjemite-Tonalite-Granodiorite in compositions and intercalated with amphibolites. Igneous zircons from gneisses and amphibolites have U-Pb ages of 2.86 and 2.75 Ga respectively, which are interpreted as the crystallisation ages of their protolith. Zircons from amphibolite and gneiss have eHf(t) values of 2.4–15.5 and -3.0–1.5 respectively. The tDM2(Hf) model ages of the gneiss range from 2.87 to 3.14 Ga, which is consistent with tDM1(Hf) ages of amphibolite (2.84–3.16 Ga). The U-Pb-Hf isotopes thus confirm that the gneisses were generated by partial melting of amphibolite. Two granites produce two group Hf isotopic compositions. The older one (1916 ± 42 Ma) has eHf(t) values and tDM1(Hf) ages of -9.4–3.4 and 2.24–2.71 Ga respectively, whereas the younger one (1823 ± 41 Ma) shows a large variation in eHf(t) values of -18.1–12.5 and tDM1(Hf) model ages of 1.73–2.92 Ga. Geological and geochemical characteristics indicate that the Huoqiu banded iron formations are a Superior-type iron formation rather than an Algoma-type as previously considered.CITATION:Yang, X, Liu, L and Wang, B, 2015. Study on the Huoqiu banded iron formation, West Anhui Province, East China , in Proceedings PACRIM 2015 Congress, pp 649–656 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By L. Kilburn

"A survey of 281 mineral exploration agreements examines the ratios among three ways that may be used to purchase an interest in a mineral property, viz: pay cash, pay shares and make future expenditures on the property.The dollar value of the future expenditures exceeds that of cash or shares by about nine times in most of the 110 agreements that contain cash-expenditure or share-expenditure components. Results suggest that cash and shares are treated about the same in terms of value.Buyers and sellers have opposing priorities for the way that they prefer to purchase a mineral property. These opposing priorities should give rise to a perceived 50:50 balance between cash/share payment and future expenditures to satisfy the idealized situation described by most definitions of fair market value (FMV). This balance between cash/share payments and future expenditures appears to be rationalized in negotiations to a FMV when expenditures are nine times greater than cash and/or payments.On this basis, it is proposed that the FMV of a property may be determined by aggregating the dollar amount of the cash/share payments plus one-ninth the dollar value of future expenditures, as set forth in the respective purchase agreement, and proportionately applying such aggregate to full property value."

Jan 1, 2005