Search Documents

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue. The author wishes to acknowledge the assistance of the following persons: L. W. Camp, general manager; S. Cooper, plant superintendent; and W. R. Riel, office manager.

Jan 1, 1936

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, end control of anthracite-line fires, it was observed that the carbon monoxide disappeared from a scaled fire area much more rapidly than could be explained oil the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance; (1) That the carbon monoxide was oxidized at temperatures below 150° C, by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By Ádria Rocha Corrêa

Durante a solidificação de ligas metálicas, o produto fundido se contrai, o qual provoca o surgimento de espaçamentos vazios na interface metal/molde chamados de “gaps”. Estes gaps causam o aumento da resistência térmica influenciando em toda a cinética da solidificação. A transferência de calor durante a solidificação depende do conhecido parâmetro chamado de coeficiente global de transferência de calor ( hg). Este parâmetro é representado pela equação do tipo: hg =C.t-n, a qual indica que a eficiência térmica na interface metal/molde decai com o tempo. Muitos parâmetros podem influenciar o coeficiente global de transferência de calor (hg), neste estudo, os percentuais de Sn em ligas do sistema Al-Sn são analisados (10,20,30 e 40%Sn). Portanto, o principal objetivo deste estudo é propor uma relação matemática que descreva, para o sistema Al-Sn, a evolução hg em função do teor de Sn. A relação matemática foi obtida através do método dos mínimos quadrados

Aug 17, 2017

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer's equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

Jan 1, 1964

By Nicholas Chlumecky

One of the oldest mine supports in use today is timber cribbing. In many mining operations material, installation and maintenance costs for timber cribbings are substantial. Their performance characteristics also add to mining costs. During the 1970'6, the U.S. Bureau of Mines recognized many of the deficiencies of timber cribbing and very successfully initiated the development of steel-fiber- reinforced (SFR) concrete blocks. Since the early 1980's this SFR concrete cribbing has been manufactured as a high quality product which has found increasing acceptance by mine operators. The rapid acceptance of the SFR concrete block cribbing has proven that its use is eliminating many of the deficiencies of timber cribbing while providing superior load carrying capability. The use of SPR concrete blocks to build the cribbing is based on the same principle as wood. That is, stacking longitudinal, rectangular blocks in layers in a crisscross manner. The blocks are positioned at right angles to the blocks of the layer below. With this situation, the possibility of misalignment exists when the concrete blocks at the base are not placed exactly parallel or when the blocks of the base are subject to unequal settlement. Such misalignments creates localized, high stress areas which reduces the load capacity of the cribbing made from SFR concrete blocks. Recognizing the problem of misalignment, the Underground Supports Division of Commercial Shearing, Inc., conceived a circular, one-piece, steel-fiber-reinforced concrete cribbing which is being marketed under the name - Donut Cribbing. This concept eliminates the possibility of misalignment and provides 100% bearing between layers of stacked cribbing as well as other advantages. The purpose of this paper is to discuss the performance characteristics, installation speed and economical factors of each of the three cribbing types -- timber cribbing, SFR concrete block cribbing and SFR concrete Donut Cribbing.

Jan 1, 1986

By R.P. Edwards, B.C. Flintoff

Froth flotation is one of the most widely used and effective processes for mineral benefication. First introduced in 1911, flotation technology has seen many developments over the past 80-plus years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results." Klimpel [1988] While reasonable was sufficient in the past. competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway.

Jan 1, 1995

With the proving of a mineable orebody at Orlando in May 1961, Peko Mines N.L. was faced with the decision of whether to mill the ore on site or to haul it 25 miles to central facilities at Peko. Orlando was a relatively small orebody, so that it was decided to haul, although no reliable assessment of possible ore haulage costs was available.The necessity for a good haul road was recognised from the beginning and a 17 mile, 12 ft wide, single seal bitumen road was constructed, to link the mine to the Stuart Highway and Peko. The initial selection of 20 ton capacity diesel-powered end-tipping ore carts was made, with the best information available at the time.Since then some 130,000 tons of ore have been carted over a period of 3 years, and this paper presents the experiences of this haulage operation and the lessons learned.A second mine has just been brought into operation at Ivanhoe, 19 miles from Peko. For this haul it was decided to use an ore haulage vehicle of the side tipping road train type, which would cart some 70 tons, or more than three times the load of the vehicles initially selected.Only about 5,000 tons had been hauled at the date of this paper, but preliminary figures indicate a cost 01 1· 65d./ton-mile as against 2·47d. for the smaller vehicles.It would appear that the road haulage of ore from small outlying mines to a central plant can be highly economical, if certain basic rules concerning haul roads and vehicle selection are followed. This paper does not try to determine the maximum tonnages and haul distances which would finally make road hauling uneconomical...

Jan 1, 1966

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By S. J. Lötter, J. T. Nel, W. Purcell

"SynopsisGlow discharge optical emission spectroscopy (GD-OES) is an analytical technique used in the analysis of solid, conducting materials. Though primarily of interest as a depth profiling technique on samples with varying layers of both conducting and non-conducting materials, it is also capable of rapid bulk analysis of homogenous, solid samples. GD-OES combines the advantages of ICP-OES (wide detection range, speed, and lack of interferences) with the solid sampling of XRF techniques. This allows the analyst to not only quantify the elemental composition of a sample, but to evaluate it in terms of homogeneity with depth, a field in which auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS) have traditionally been the primary techniques. Although GD-OES does not replace these useful techniques, it does offer various advantages over them, making it an excellent complementary analytical tool.In GD-OES analysis, a low-pressure glow discharge plasma is generated with the sample material acting as a cathode, accelerating the cations in the plasma towards the sample surface. This bombardment causes the sample material to ‘sputter’, essentially knocking free atoms or molecules of analyte material, which are then drawn into the plasma where they are excited. The light emitted by this excitation is then diffracted to separate the wavelengths emitted by the specific elements and detected by a spectrophotometer. The intensity of the signal is directly proportional to the quantity of analyte element present in the sample, allowing simple calibration and quantitative determination of the elements. Technological improvements made in the past twenty years or so have significantly increased the usefulness of GD-OES for surface analysis. Faster plasma stabilization and start-up allow for the quantification of surface layers as thin as 1 nm. Sputter rates have been accurately measured for many common materials, allowing them to be built into software libraries in the instrument’s control software. This dramatically expands the usefulness of this software and the ease of performing analyses.GD-OES analysis of nuclear materials allows for the rapid determination of the elemental composition without the requirement of initial dissolution. The thickness of any corrosion layers on nuclear materials can also be determined."

Jan 1, 2015

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By Robert F. Chaiken

Burnout Control is a process developed by the U.S. Bureau of Mines for accelerating the burning of wasted coal fires in situ, while at the same time controlling the heat and fumes produced. The Albright fIre project is a fIrst fIeld trial of Burnout Control as applied to a coal waste bank. An exhaust ventilation system was designed and constructed and then operated over a 1-year period at the site of an existing abandoned mine land fire near the town of Albright, WV. While predicted exhaust gas temperatures of 900° C and thermal power levels of 5 MW were achieved at 20-to 3O-in H20 vacuum levels, problems were encountered with engineering designs, equipment breakdown, and fuel-rich combustion that curtailed the time period of satisfactory operation. Effective afterburning of the exhaust gases (as they were drawn from the bank) corrected the problems associated with combustion stoichiometry and led to high thermal outputs. It is believed that with (1) improvements in engineering design and construction, (2) better control of the afterburning process, and (3) the use of conventional stack gas air-pollution controls, Burnout Control can be applied successfully to a coal waste bank fire.

Jan 1, 1991

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001