Search Documents

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Anthony J. Konya, Calvin J. Konya

Mine sites and construction projects have faced problems with blasting a smooth back wall. This lead to safety concerns with slope stability and rock falls from the walls. Decades ago Dr. Calvin Konya began a special type of blasting called “Precision Presplitting”. This form of presplitting used relatively light loads based on the rock type being blasted. The explosive loads were estimated for each rock type and adjusted as blasting progressed. This current research project also determined a new equation for prediction of the ground vibration from one type of presplitting and compared it to vibration from production blasting.

Jan 1, 2016

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

By Agne Rustan

The 9th International Symposium on Rock Fragmentation by Blasting was held in the Granada Conference Centre, Granada, Spain from the 14th - 17th September 2009. The Symposium was preceded by a 1 ½ day Workshop on “Vibrations from Blasting” organized by the initiator Dr. Alex Spathis and his colleague M. J. Noy, both employed at Orica Mining, Australia. Prof. Josè Sanchidrian at the “Universidad Politécnic de Madrid” in Madrid, Spain was the main organizer for both the Workshop and the Symposium. A record number of participants came (292) from a record number of countries (41). There were a total of 14 papers in the Vibrations from Blasting Seminar and 96 papers and 2 Keynote Addresses in the Fragblast 9 Symposium itself. The aim with this paper is to present some results from Fragblast 9 which are of interest for a large target group. One very important result from the Fragblast 9 meeting was that it was decided there that Fragblast 10 will be held in November 2012 New Delhi India.

Jan 1, 2009

By A. S. Murphy, E. V. Manlapig, C. Green, J. W. Parkinson

Historically in Australia and the United States many coal mines deposited raw wash plant fines into large slurry impoundments. At the time the technology and market economics did not exist to make it viable to recover coal from these tailings. Today better technology exist to dredge and clean the tailings and there are circumstances where government regulations and market forces have come together to make coal recovery from these old tailings impoundments economically viable. This paper discusses the processes and equipment being used in tailings impoundment reclamation operations in Australia and the United States, and discusses the economic forces driving these operations.

Jan 1, 2001

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

By Walter Valery, Sarma Kanchibotla

Due to the global financial crisis, the world economy has turned upside down and most major economies in the world are facing severe recession for the past one and half year. During this period most commodity prices have tumbled by more than half from their peaks and such a sudden and severe economic downturn is not seen since the great depression. This sudden drop in commodity prices and lack of credit made many mining operations unviable and even those mines that are marginally viable at this point are operating under severe cost pressures and capital expenditure restrictions.

Jan 1, 2010

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By Forrest T. Moyer

The overall disabling work injury experience, excluding office- workers, at nometal mines and mills during the period 1961-63, as reported to the Bureau of Mines by operators, was 77 fatal and 7,201 nonfatal injuries during an aggregate worktime of 335,029,685 man- hours. These injuries, fatal and nonfatal combined, occurred at a frequency rate of 21.72 per million man-hours, comprising 0.23 for the fatal and 21.49 for the nonfatal injuries. The combined severity rate of the disabilities was 2,312 days lost or charged per million man-hours, consisting of 1,379 for the fatal and 933 of the nonfatal injuries, The average severity of all disabilities during 1961-63, was 106 days per injury, The number of days lost or charged, excluding officeworkers, at nonmetal mines and mills during 1961-63, was 462,000 days charged to fatal injuries and 312,461 days lost from nonfatal injuries. The outstanding causes for fatal injuries were explosions (18 fatalities occurred in a major mine-explosion disaster in a potash mine in Utah in 1963) and falls of rock or ore from back or side, while most nonfatal injuries were caused by handling materials, slips or falls of persons, haulage, and machinery. The parts of the body most frequently injured during the period 1961-63 were the trunk, hand and finger, and foot and toe, An average of 52,810 men were at work daily, There were 20 nonfatal disabling injuries reported for office- workers at nonmetal mines and mills during the period 1961-63 during an aggregate worktime of 23,088,496 man-hours, These injuries occur- red at a frequency rate of 0.87 per million man-hours, There were no fatal injuries reported.

Jan 1, 1967

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Prediction of fragmentation by blasting is most commonly based on theassumption that a single distribution of pre-existing discontinuities is present within a blasted rock volume and that the underlying mechanism of failure is tensile failure. It is assumed that the tensile stress field created by a blast initiates and extends radial cracks around the blastholes. Interaction between radial cracks from different blastholes and the free surface creates rock fragments. In reality, fragmentation of the rock occurs due to two mechanisms.One is related to the compressive-shear failure of the rock (mainly rock matrix) close to the blastholes, while the second mechanism is the previously mentioned tensile failure of the rock mass. The secondmechanism of failure occurs in the form of extension of the larger cracks in the region beyond the crushed rock, and this type of fragmentation occurs after the crushing phase. In the case of hard rock or blasting where the extent of crushing is minimal, the currently used prediction methods give a reasonably good result. However, there are many blasting conditions where the amount of rock crushing is significant. In the case where fragmentation of the given rock volume occurs dueto two different mechanisms, modeling of the rock fragmentation with a single distribution function is not appropriate. To model the fragment size distribution generated by two different mechanisms, it is necessary to use a two-component fragment size distribution function and a scaling parameter that will determine the proportion of the fragmented volume created by each mechanism. The purpose of this paper is to present results of blast fragmentation modeling based on two mechanisms of failure. The two-component model (TCM) utilises experimentally determined parameters from small scale blasting and parameters of the Kuz-Ram model, for more accurate prediction of the complete rock fragment size distribution curve. The methodology is such that it is possible to predict complete fragment size distribution, including fines, of ROM product for a future mine, at the feasibility phase of mine design.

Jan 1, 1999

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

By G. H. Babcock, D. A. Knight, V. G. Medina

"Production commenced at the Golden Sunlight Mine in 1983 and at Kidston Gold Mine in 1985. These projects were both constructed under the management of the Placer Dome Inc. (Technical Services) group of Vancouver, B.C.Golden Sunlight uses a conventional rod mill/ball mill grinding circuit while Kidston uses a SAG /ball mill, and later on, SABC circuit. Since the hardness of the ore and the fineness of the primary grind in both mines are about the same, a meaningful cost comparison can be made. The comparison is made on the basis of capital and operating costs.The result of this study indicates that a significant capital cost savings can be achieved in favour of the SAG /ball mill circuit when the ore is amenable to semi-autogenous grinding. With a good maintenance program, the operating cost for the SAG /ball mill circuit could also be lower that the conventional rod mill/ball mill circuit.HISTORYGolden Sunlight MineGolden Sunlight is a 5 530 t/d gold mine located near Whitehall, a small town 60 km east of Butte, Montana. Originally optioned by PDI U.S. in 1958, the development of the property waited until 1981 when economic conditions became favorable for the project to proceed.Semiautogenous grinding tests were conducted during the final stages of the feasibility study. The hard near surface ore was not quite amenable to semi-autogenous grinding. The best result produced from a series of tests using a 1.83 m diameter mill was a semiautogenous work index of 39. This is substantially higher than the 22 Bond work index of the sample used in the testwork. A conventional SAG/ball mill circuit for this ore will be extremely inefficient, and for this reason, this circuit was rejected in favour of a conventional rod mill/ball mill circuit."

Jan 1, 1991

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By John R. Benham

The Windigo Theilson RARE II area has a low mineral potential. There are no mines or claims in the area. The only observed results of mining activities were five prospect pits near Tolo Mountain. Samples from these pits contained no significant assays. The study area contains more than 190 million cu yds (145 million m3) of cinders in 17 cones. Development of these cinders is unlikely because their locations are remote, and other sources supply area needs. The Geological Survey has classified the area as prospectively valuable for geothermal resources. However, there has been no geothermal exploration activity.

Jan 1, 1982