Search Documents

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By Walter Durst

On October 16, 1978, the Harnback open cut of Rheinische Braunkohlenwerke, the largest open cut ever planned, was officially put into operation. It will outperform all of the large open cuts known at present, both in its dimensions and in its annual output of overburden and coal. Present plans are to commence coal mining in 1983, although target production will only be achieved in 1995when the annual output will be 50 million tons of coal. Considering an overburden: coal ratio of 6: 1, this will involve the removal of approximately 300 million bank cubic metres of overburden. For overburden removal and coal mining, this open cut will use bucket-wheel excavators exclusively. It is planned to employ eight excavators with a daily output of 240,000 bank cubic metres each (Fig. 1). The transport of the overburden and coal to the dump and the power station, respectively, will be effected by 30Q0-mm-wide conveyors, running at a speed of 6 m/sec. The overburden will be dumped by spreaders having a boom length of 100 m, capable of dumping 240,000 bank cubic metres per day (Fig. 2). Such giants, of course, can only be used for extreme conditions . Their employment indicates that huge quantities of material can be handled economically for long periods. However, the use of bucket-wheel excavators is economic when daily outputs of 5,000 bank cubic metres are involved, in particular if direct backcasting of the overburden is not possible.

Jan 1, 1979

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

Jan 1, 1969

A study of the accessory opaque iron-titanium oxide minerals of the Oiles Complex, central Australia, was an Important complement to an investigation of the magnetic properties of the Complex. These minerals constitute no more than 10 per cent of the rocks sampled, and generally less than 1 per cent of the ultramafic rocks ("magnetite" concentrations were not sampled for magnetic investigation).Titanomagnetite is the main opaque mineral present, although ilmenite exsolution has been widely developed. High-temperature oxidation of these produced mainly titanohematite, pseudobrookite and rutile. Both exsolution and high-temperature oxidation developed along specific crystallographic directions (along {111}), and in Irregular patches. Low-temperature oxidation is generally not well-developed, indicating the small degree of weathering in the rocks sampled.Although the Oiles Complex is layered, no apparent overall preferred orientation of the iron-titanium oxide minerals was observed, other than crystallographically controlled alignment of very fine grains within pyroxene crystals. Other textural features of the opaque oxides are restricted to symplectic intergrowths mainly with the ferromagnesian silicates.

Jan 1, 1971

By R. L. J. Phillips

"The environmental impact of the Rabbit Lake project is presented. Baseline data for fish, water, air and radon collected in 1973, 1975, 1980and 1986, are compared with post-development environmental monitoring data. Predicted environmental impacts for the developed Rabbit Lake and B-zone deposits are compared to the actual impacts. INTRODUCTIONThe environmental impact of the Rabbit Lake project has been documented through the years in several submissions to the government agencies. In 1972, the environmental baseline study for the Rabbit Lake area was completed prior to any mining activity at the Rabbit Lake pit (Fig. 1).Sampling concentrated on Hidden Bay and Pow Bay, which received the treated effluent and the waters drained from Rabbit Lake respectively.A second baseline study was done on the Collins Bay area in 1980(Fig. I) in preparation for the mining of the B-zone pit. The detail in this study was considerably greater than the detail in the previous study. Collins Bay and Harrison Peninsula were the areas sampled. The B-zone deposit is being mined at present.With the discovery of the A-zone, D-zone and Eagle Point deposits, it was decided in 1986 to begin proceedings to obtain approval from Saskatchewan's Department of the Environment, and from the Atomic Energy Control Board to develop these deposits.In preparation, a third baseline study of both the Rabbit Lake and Collins Bay areas was done in 1986 and 1987. The emphasis was to establish the baseline at the three new deposits, to quantify the actual impacts of the existing Rabbit Lake operations and to confirm the Collins Bay B-zone (1980) impact predictions. The new deposits will allow us to continue to produce uranium into the future. In January 1988, Saskatchewan approval was received.Since 1975 in the Rabbit Lake area and 1980 in the Collins Bay area, routine environmental monitoring has been done. This has resulted in one of the largest and most comprehensive environmental data bases in North America in mining. By the time the Eagle Point deposit is mined to completion, there will have been data collected for approximately 40 years.Further discussions follow which describe the impacts of the past (1972 to 1984), the present (1985 to 1987) and the future. In addition, the past and present performances and the future plans of the .waste management systems will be discussed."

Jan 1, 1989

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By R. B. King

This document was prepared by the DFI International Grouting Committee with the intent to provide a summary of main Standards and Guidelines available for the North America and Europe grouting industry. This document highlights the different approaches, methods and tools used internationally. The DFI International Grouting Committee comprises all parties involved on a grouting project: Owners, regulators, engineers, contractors, and manufacturers (equipment and materials). This document is not intended to cover every conceivable application or requirement of grouting. However, it does provide standard practice requirements for qualifications, materials, equipment, testing, and production procedures for the professional engineer to incorporate into their project specific requirements.

Jan 1, 2021

Overview ?G-9 Discovery Hole 420 drilled May 2005 ?14.16% Zn, 1.76% Cu ?Greenfield discovery built into the G-9 Mine in under 4 years. ?Utilized a unique ?Parallel Track? approach to fast-track mine development. ?Raised over $200million in financing without a Feasibility Study. ?Mine built for $149.7 million, only 20% over PEA. ?Commercial Production declared April 1, 2009. ?G-9 Mine has now completed the first year of commercial production on April 1, 2010. ?Initial cash costs per pound of zinc US$0.39/lb -US$0.45/lb range. ?Mill operating at over1,900 tpd in March 2010, well above design capacity (1,500tpd) only one year after starting commercial production. ?Balance Sheet -$167 million assets, $24 million long-term debt, $22 million cash. ?Restarted Exploration ?excellent initial results. ?Strategically positioning Farallon to grow to a mid-tier mining company.

May 1, 2010

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

Flotation Research on Cassiterite of Tailings

Sep 13, 2010

Jan 1, 1988

By Rustu S. Kalyoncu

Nonoxide ceramics with improved high-temperature properties could substitute for high-temperature alloys and reduce toe Nation's dependence on imports of Cr, Co, Ni, and Mn. To meet this objective, the Bureau of Mines conducted research to synthesize u1trafine reactive boron nitride (BN) powders BN powders were prepared at temperatures ranging from -75? to 750? C. Low-temperature reactions (-75? to 200? C) between boron halides and N compounds led to formation of e1emento-organic compounds that were thermally decomposed to u1trafine (approximately 100-to 150-A particle size) reactive BN powders. BN powders were also prepared through the reaction of a 10w-me1tinginorganic B compound (boric acid, borax) with an organic N compound (carbimide and thiocarbimide) in N2 and/or ammonia (NH3) atmospheres at temperatures between 500? and 750? C.

Jan 1, 1986

By Tanner A. C, Harraway D. H

Various circuits were tried at Mount Isa Mines during the period 1959 to 19G3 with the objective of improving the differential flotation of galena and sphalerite. Many benefits and disadvantages of the various circuits were revealed. An analysis' of ore characteristics and their effect on flotation was made -and resullted in the design of a proposed circuit which is currently in the process of installation.INTRODUCTIONSince 1936 when lead-zinc sulphide flotation commenced at Mount Isa, at least three types of ore have been encountered.Each ore has presented problems to flotation metallurgists.The three types of ore are,1. partially oxidized upper level sulphide ore,2. Black Star ore from the lower levels with its carbonaceous fraction, and3. Black Rock ore which is similar to 2, but more free milling.In retrospect a number of the metallurgical successes of the past were short lived. Often flowsheets or 0perating practices were designed to solve a single metallurgical problem associated with the current ore being treated. As the ore changed the problem would vanish and the method originally taken to counter the problem could become unnecessary or deleterious to the treatment of the new ore. The general lesson learnt from-the past-is-that thetreatment of Mount Isa lead-zinc ore involves a number of equally major problems...

Jan 1, 1963

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008