Search Documents

By Peter Riba

Up until ten years ago the industry had arrived at a relatively conventional, and consistent design of coke ovens. Through the years the designers and builders were not being heavily taxed to come up with revolutionary new designs. However, the stimulus for design change was ever present. These stimuli for change are quite important and they are the driving force which produce improvements. The most obvious stimulus to change a design is commercial. To "build a better mouse trap and the world will beat a path to your door" is the well used cliche which best befits this philosophy. As in all businesses, coke oven designs require that all of the considerations, which affect the cost or the desirability of the design, be optimized. One way to increase the desirability of the particular design, 1s to make the design in- expensive to operate. Or, put another way, to increase production for the same operating cost

Jan 1, 1980

By Michelle Lostra, Red Blanchette, Jan Babendererde, Greg Colzani

The City of Portland’s Westside CSO Project is constructing a deep tunnel system to reduce combined sewer overflows (CSO) from entering the Willamette River. Several kilometers of microtunneled pipelines connect the existing system to the new tunnel. The alignments encountered a variety of ground conditions, including fill, manmade obstructions (wood, steel piles, debris), fine-grained to dense coarse-grained materials, cobbles and boulders, all below groundwater. A slurry MTBM convertible to varying diameters, equipped with mix shield capabilities, was selected to cope with the conditions. This paper will discuss access shaft construction,

Jan 1, 2005

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

By F. C. Harvey

The Annual General Meeting of the Orange Free State Branch was held on Wednesday evening, 30th July, 1986, in the VIP Lounge of the Freegold North Region Canteen. The meeting was well attended, a total of 73 members, guests, and visitors being present. It was extremely pleasing to have such a large number of lady visitors present.

Jan 1, 1986

By S. du Plessis

Nationalization is high on the policy agenda in South Africa. This paper considers the case for nationalizing the local mining sector from an evidence-based perspective, which is derived from theoretical considerations and related to the known features of the South African mining sector and economy. A strong case against nationalization emerges, which can be summarized as follows. The mining sector is competitive and therefore a poor candidate for public ownership. Furthermore, the resources sector does not dominate the South African economy nor does it create the risk of a decrease in the competitiveness of the industrial sector via the unintended adverse impact of an appreciating real exchange rate due to a commodity boom (Dutch Disease). Nationalizing the mining sector will cost the government more than it receives. This is not only a bad idea in itself, but it will limit the scope for distributive policies on the national budget. The contemporary international experience demonstrates the risks of fiscal imprudence. Finally, nationalizing the resources sector will undermine support for those very market-based institutions required to achieve a higher long-run growth trajectory.

Jan 1, 2013

By Richard V. Ageton, Harry E. Tufft, E. A. Holbrook

When an underground excavation is made, the rock surrounding the sides and top of the opening is deprived of its natural support and tends to fall. Whenever caving takes place, the time and extent of the caving depend on the character and condition of the rock. In strong homogenous rock, such as solid granite, even a large chamber may stand indefinitely, whereas a soft material, such as clay or a loose material like unconsolidated sand, falls immediately if not supported. Weaknesses in the rocks induced by structural features, such as joints, :fissures, bedding and cleavage planes, and fractures produced by blasting, will cause the falling of insecure blocks or slabs unless means are provided to support these in place. In an unsupported mine opening, as a tunnel, the first slight settling or adjusting movement of the rocks (the "initial creep" or "set") is caused by the great weight of overlying material pressing down the rock masses above and around the roof and sides of the opening until they key together in roughly the form of an arch. The rock, after it has adjusted itself to this shape, becomes. selfsupporting. Timbering is necessa.ry in all mining only to support, therefore, those comparatively small blocks or pieces of rock which tend to loosen from the top and sides of the opening during or after the formation 'of the natural rock arch, and which lie between this natural rock arch and the opening. This statement, of course, has its limitations. For example; a layer of strong rock, like limestone, may act as a beam; then only the material under the limestone will need support. Timbering is not, as is commonly supposed by the layman, used to supp!ort the huge mass of rock between the back (roof) of an underground opening and the surface. It would be impossible to place enough timbers in a:ny underground opening to support such a mass. This fact is not'·perceived by all miners.

Jan 1, 1923

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By Alan Jessop

A small group has been set up at the Dominion Observatory, Ottawa, to make a survey of terrestrial heat flow throughout Canada. Terrestrial heat flow is the heat rising from the interior of the earth and escaping at the surface, and is calculated from a knowledge of under-ground temperature distribution and the thermal conductivity of rocks. A small number of diamond drill holes are being sunk for the purpose of measuring temperatures below the surface, but the program is inadequate for a thorough survey. Mines and holes drilled for other purposes are being sought by the Dominion Observatory group to supplement their own drilling program. F ROM January, 1.962, to December, 1964, geo-physicists of many nations will be cooperating in the "International Upper Mantle Project." Unlike tl1e International Geophysical Year, which was mainly concerned with the fluid layers surrounding the earth, the Upper Mantle Project is an intensive study of the solid earth. Canada, with its large land area and extensive Precambrian Shield, is an active participant in the project.

Jan 1, 1964

By James McNally, Adam Stremcha, John MacGregor

With 13.7km of TBM tunneling in Atlanta’s hard gneiss well under way, drill and shoot work continues on several sites throughout the city. In order for the City of Atlanta to meet the consent decree imposed by the federal government, an aggressive construction schedule was a necessity. Construction consists of two deep, large diameter tunnels, four construction shafts, a pumping station, one overflow shaft, three large intake structures, and two connecting tunnels. Due to the multitude of blasting insensitive urban environments, a high standard of seismic and air-overpressure criteria, coupled with time restrictions, was adopted for the project. At any given time, drill and blast operations were under way at four of the seven sites requiring a certain amount of coordination between the TBM excavation, surface work, and the forces of Mother Nature. This paper addresses the challenges faced and the techniques used to safely and successfully complete the rock excavation of the West Area CSO Tunnel and Pumping Station project.

Jan 1, 2007

By Frederick W. Breaks, Andrew G. Tindle, Julie B. Selway

"Abstract - Rare-element pegmatites may host several economic commodities, such as tantalum (Taoxide minerals), tin (cassiterite), lithium (ceramic-grade spodumene and petalite), and cesium (pollucite). Key geological features that are common to pegmatites in the Superior province of Ontario and Manitoba, Canada, and in other large tantalum deposits worldwide, can be used in exploration.An exploration project for rare-element pegmatites should begin with an examination of a regional geology map. Rare-element pegmatites occur along large regional-scale faults in greenschist and amphibolite facies metamorphic terranes. They are typically hosted by mafic metavolcanic or metasedimentary rocks, and are located near peraluminous granite plutons (A/CNK > 1.0). Once a peraluminous granite pluton has been identified, then the next step is to determine if the pluton is barren or fertile. Fertile granites have elevated rare element contents, Mg/Li ratio < 10, and Nb/Ta ratio < 8. They commonly contain blocky K-feldspar and green muscovite. Key fractionation indicators can be plotted on a map of the fertile granite pluton to determine the fractionation direction: presence of tourmaline, beryl, and ferrocolumbite; Mn content in garnet; Rb content in bulk K-feldspar; and Mg/Li and Nb/Ta ratios in bulk granite samples. Pegmatite dikes with the most economic potential for Li-Cs-Ta deposits occur the greatest distance (up to 10 km) from the parent granite.Metasomatized host rocks are an indication of a nearby rare-element pegmatite. Metasomatic aureoles can be identified by their geochemistry: elevated Li, Rb, Cs, B, and F contents; and by their mineralogy: presence of tourmaline, (Rb, Cs)-enriched biotite, holmquistite, muscovite, and rarely garnet.Once a pegmatite dike has been located, the next step is to assess its potential to contain Ta mineralization. Pegmatites with the highest degree of fractionation (and thus the most economic potential for Li-Cs-Ta) contain blocky K-feldspar with >3,000 ppm Rb, K/Rb < 30, and >100 ppm Cs; and coarsegrained green muscovite with >2,000 ppm Li, >10,000 ppm Rb, >500 ppm Cs, and >65 ppm Ta. Pegmatites with Ta mineralization usually contain Li-rich minerals (e.g., spodumene, petalite, lepidolite, elbaite, amblygonite, and lithiophilite) and may contain Cs-rich minerals (e.g., pollucite, Cs-rich beryl). The ore minerals of Ta are commonly manganotantalite, manganocolumbite, wodginite, and microlite; Ta-rich cassiterite is also commonly present. Tantalum mineralization tends to occur in albitic aplite, mica-rich (lepidolite, cleavelandite ± lepidolite), and spodumene/petalite pegmatite zones."

Jan 1, 2005

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"In the present study classical induction design tools are applied to the problem of heating nonmagnetic metal billets, using 50 Hz AC. As an example of great practical industrial interest, the induction heating of aluminum billets is addressed specifically. The predicted work piece power is compared with the measured work piece power for a long and a short coil, using well established methods, such as those of Burch and Davis, introduced in 1926/28, Dwight and Bagai in 1935, Baker in 1944/57, Vaughan and Williamson in 1945, and by Tudbury in 1960. A calculation methodology based on a combination of the available tools is also introduced and discussed. The method has proven to give an error of <10% of the actual work piece power. An equation for Tudbury's work piece shortness correction factor is disclosed for the first time.IntroductionInduction heating of metal billets is a practical problem, with a geometry suitable for solution using analytical methods. This paper will examine solutions related specifically to round work pieces in round coils, although the methods presented can be extended to other regular shapes of work pieces and coils[l]. The methods can also be extended to ferromagnetic materials with slight changes[2-3]. It is assumed that the coil and work piece have a consistent diameter over their entire length and that the work piece is at least as long as the coil. Correction factors can be derived for the cases where the work piece is shorter than the coil.The study of induction heating by coils began in the late 19th century with theoreticians like Heaviside[ 4]. The work of Burch and Davis[ 5-7] in the 1920' s greatly improved the theoretical understanding of induction applied to metallurgy. Many investigators in the 1930's-1950's: Dwight and Bagai[8], Baker[l-2, 9], Vaughan and Williamson[3, 10] and others[l 1-12] added to our understanding with clearer mathematics, solutions for specific applications, semi-empirical modifications and practical design tools. Much of the accumulated knowledge is available in books, such as Tudbury's practical text or Simpson's engineering guide from 1960[13-14]. Perhaps the best description and derivation of the theoretical and semi-empirical solutions can be found in Davies[15]."

Jan 1, 2011

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980