Search Documents

By M. A. Barron, D. Y. Medina, R. T. Hernandez, I. Hilerio

"Chromium Nitride (CrN) thin fihns were deposited on steel AISI 316 substrates with reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a d.c. source. At the second coating was applied a negative substrate bias voltage. X ray diffraction, quantitative energy dispersive and scanning electron microscope, were employed to characterize their phases, chemical composition and microstructure. Additionally microhardness was evaluated using a microhardness tester. The results show that the phase formation of CrN thin films in the first case (with temperature) is better. Both coatings presented homogeneous surface. Their compositions shows differences though that gases flow are same. In attention to their hardness, presents an increment if it's compared with hardness substrate.Nomenclature.P Ar =Argon gas pressure during coating.PN2 = Nitrogen gas pressure during coating.Ts = Substrate temperature during coating.T f = Coating melting temperature. (CrN = 1050°C).E=Potential difference.t =Coating time.P=Target power (Cr) in magnetron sputtering de.HV = Vickers hardness.F = Applied charge.d= Average length of longitude of the two diagonals (mm)Introduction.Wear causes losses in materials surface, generating that components of mechanical systems suffer irreversible changes in their properties, causing a faulty operation of the system. It is important to control their effects, measuring and interpreting their causes clearly."

Jan 1, 2013

By I. Iwasaki

Flotation characteristics of pyrrhotite by itself and in complex sulfide ores are reviewed with respect to the effects of oxidation, grinding media and other electroactive minerals.

Jan 1, 1988

By Robert T. Oxnard

"EXECUTIVE SUMMARYThe history of Refractory Recycling indicates there was little recycling until the 1950s. Energy incentives were the primary reason for the beginnings of a recycling effort by the refractory brick manufacturers. Quality benefits quickly became evident and fewer rejects were the result. Today, economic factors including higher valued raw materials and increased competition are the driving forces of refractory recycling.There are some success stories in refractory recycling but we have a long way to go. Few incentives, quality concerns, relatively cheap energy, comparatively lax government regulations, inexpensive landfills and inexpensive substitutes make recycling a difficult choice for many companies. Marketing advantages such as ISO 14000, eliminating multiple audits and reduced liability exposure can tip the scales toward recycling viability. Increasingly, the ideological philosophy of a company, a desire to minimize environmental impact and develop favorable public and other interested party perceptions can drive recycling and waste minimization efforts.Recycled materials can be more trouble ""up front"" and harder to ""manage"" due to their suspect quality. However, due to their nearly inexhaustible supply and the fact that once developed, they constantly contribute to the bottom line, they are certain to be the materials of the future. Waste refractory materials will likely see the same bright future as the steel scrap yards and slag piles of yesterday. In hindsight, we will realize that now was the perfect time to prepare and plan for the bright future of refractory recycling."

Jan 1, 2000

By Jing Zhang, Chenguang Bai, Fusheng Pan

"The microstructure and hot deformation behaviour of an Er-modified Mg-Zn-Ai alloy were evaluated. The results showed that the addition of rare-earth Er changed the morphology of the quasi-continuous grain boundary networked eutectic compound to globular particles. Moreover, a self-strengthening effect was identified for the alloy, which determined its deformation behavior. After hot extrusion, the yield strength and elongation to failure of the Mg-Zn-AI-Re alloy at 200°C were increased by 105% and 120%, respectively, due to an emerged dynamic precipitation strengthening mechanism.IntroductionMagnesium alloys are attracting increasing attention for applications in automobile, electronic devices and hand tools for weight reduction and higher fuel efficiency, because of their lightweight and a high specific strength. However, application of Mg is still very limited. The largest applications are still those non load-bearing castings used at room temperature, such as box case, housing, and covering. One of the main reasons is the inadequate absolute strength both at room temperature and elevated temperatures (> 100°C) of the commercially used AZ, AM series alloys, due to the incoherent interface between the secondary phase y-Mg17AI12 and Mg matrix, as well as the low thermal-stability of the y phase [1]. Besides, the heat-resistant magnesium alloys which contain rare earth (Re) as the main alloying element are very expensive. The other reason is their poor deformability. The key solution is therefore to develop low-cost heat -resistant wrought alloys."

Jan 1, 2012

By Alice Barreto Bevitori, Frederico Muylaert Margem, Renan Sopeletto Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The ramie fiber is one of the strongest lignocellulosic fibers with applications ranging from simple items such as fabrics and ropes to engineering composites for automobile parts and building panels. Characterization of the ramie fiber has recently been conducted for physical and mechanical properties. In principle, thinner ramie fiber could be comparatively stronger and consequently more effective as a composite reinforcement. In this work an attempt to correlate the ramie fiber elastic modulus obtained in tensile test with its corresponding diameter, precisely measured by means of a profile projector, was carried out. Tensile results analyzed by the Weibul1 statistic showed a significant increase in elastic modulus with decreasing the diameter of ramie fiber. Scanning electron microscopy observation of the fracture of selected ruptured fiber revealed possible mechanisms that could justify the elastic modulus/diameter inverse dependence.IntroductionEngineering applications of natural fibers obtained from cellulose-rich plants, also known as lignocellulosic fibers, are currently being the focus of attention. In fact, they are considered an enviromnental1y correct alternative to substitute synthetic fibers such as the glass fiber, associated with an intensive intake of energy during production, as reinforcement of polymer composites [1-4]. In recent years there has been a growing tendency towards the use of lignocellulosic fiber composites in several industrial sectors from civil constructions to car making. In particular, the automotive industry is expanding the number of both interior and exterior components made of natural fiber composites [5]."

Jan 1, 2012

By Ana Bohé

Nowadays, Gas-solid processes are widely used in the industry. The chloration and carbochlorination of metallic compounds are some of this kind of non catalitic heterogeneous reactions. In particular those related with extractive metallurgy of refractory elements (Zr, Ti, Nb, Ta, RE, etc). The development of materials to be used in reactors at elevated temperatures and with high corrosion performance, enhance the application of this kind of processes. Although they are currently carried out in the production of many comodities, the mechanism of most of them are yet not well understood. The present work is a deep discussion on the most important aspects to take into account for determining the mechanism of gas- solid reaction, and those criteria fulfil in this analysis were applied to chlorination and carbochlorination examples. The microstructural characteristic of solids, the mass and heat transfer phenomenon, the adsorption and desorption of gaseous species on active surface, surface diffusion processes and chemical elementary steps, which are the mainly contributions to the mechanism of these reactions were analysed. Furthermore, the effect of them on the reactivity of solids and the control step of the reactions were determined. The application of catalitic mathematical models to this kind of reaction and the modification for the better interpretation of experimental results is also undertaken. The most appropriate experimental procedures for following these reactions and the microstructural characterization techniques needed to be use in each case, there limits and applicability are also indicated.

Jan 1, 2006

By L. E. Murr

Preliminary studies of bacterial attachment to MoSp (molybdenite) have indicated a low correlation between dislocation density in the (0001) basal plane and the density of attached microbes. In the present investigation, poly- crystalline thin sections of CuFeSp (chalcopyrite) have been ion-etched or carefully comminuted to electron transparency and observed in the transmission electron microscope. The thinned test sections were then immersed in a culture solution in which bacterial attachment occurred. The attached bacteria were biologically stained in a uranyl acetate solution and the entire thin CuFeSp sections or tiny particles containing thin, electron transparent edges with bacteria attached were observed in the transmission electron microscope, allowing the coincidence of bacteria and their density to be directly observed in relation to lattice dislocations and crystallographic orientations of the exposed surfaces. This technique has the advantage of exposing crystallographic orientations where dislocation lines intersect the free mineral surface, and the emergence sites of dislocations could in principle be directly investigated as a possible preferential attachment site for bacteria. Bacteria morphologies were also extensively observed in the scanning electron microscope. The implications of the results are that although a strong correlation between dislocation density and distribution and bacterial attachment, density, and distribution has not been established, systematic multiplication of dislocation densities in crystalline mineral particles to be leached could enhance leaching rates by increasing the reaction rates as well as the density of attached bacteria at crystalline, metal-rich phases. Techniques for dislocation production in mineral and ore bodies and the particular implications in chalcopyrite leaching are discussed in relation to in-situ leaching where comminution is attained by explosives and the generation of strong shock waves in an ore body. The present study demonstrates the use of microanalytical and microscopic techniques in the investigation of fundamental microstructural phenomena in hydrometallurgical processes.

Jan 1, 1976

By David Langberg

Recovery of dissolved copper from discard slags is a critical consideration affecting the economics of copper smelting. Slag cleaning is frequently carried out in electric furnaces, however reduction by injection of natural gas in a holding furnace may offer a lower cost alternative in some circumstances. As the residence time of the injected gas is short, the factors controlling the rate of reduction need to be clarified in order to optimise the design of the slag cleaning furnace. A series of medium scale (200 kg) reduction tests to investigate the rate of reduction of copper-containing slags by injection of natural gas-nitrogen mixtures between 1150-1250C was carried out by CSIRO Minerals. The composition of the gas in the top-space of the reactor was found to be significantly more reducing than the slag, indicating that thermodynamic equilibrium was not established between the slag and the gas in the bubble plume. An apparent first order rate law was observed between the rate of oxygen elimination from the bath and the magnetite concentration of the bath. The dissolved copper concentration was closely correlated with the oxygen potential of the slag, suggesting a partial equilibrium between the dissolved components of the slag. The utilisation efficiency of the natural gas decreased as the natural gas flow rate was increased. The results of the tests tend to indicate that the rate is controlled by a mixed reaction kinetics/ mass transport mechanism. The work was supported by Xstrata Copper ? Mt Isa Mines.

Jan 1, 2006

By Jian Wang, Hongyang Cao, Binxiu Wu, Junhong Li, Jimin Wang

"The enrichment and separation of scattered metal indium component in the pressure leaching solution with sulfuric acid from vacuum furnace germanium slag were studied by iron substitute and P204 extraction, which is supplied by shaoguan smelter. The experimental results show that the extracting power of P204 for indium from pressure leach solution is powerful. The optimal technological condition were the ratio of P204 and sulphonating serosene 3:7, phase ratio 1:3, solution pH 1.2, and extracting 5 minute. The enrichment indium solution of 21.7 g/L In at 95.2% recovery ratio was obtained by three-stage counter flow extraction and four- stage counter flow stripping.IntroductionScattered metals, such as Indium and germanium, were inriched as intermediate product or by-product during the metallurgy process of other non-ferrous metals, such as lead, zinc, copper and tin. For example, the indium and germanium were inriched in vacuum furnace germanium slag, which is the by-product of zinc vacuum distillation operation from hard zinc. It is difficult to recovery the indium from the vacuum furnace germanium slag, because the indium content is low, and the chemical composition and phase compositon were complex.Recovery indium from bearing indium zinc slag was researched extensively, such as pressure acid leaching, high temperature evaporation, solvent extraction method[l-7], acid leaching method has the advantages of high leaching rate, which can be separated hydrochloric acid, sulfuric acid and silicon fluoride acid systems. Solvent extraction method has the advantages of low production cost, fast reaction speed, high enrichment ratio, and simple operation."

Jan 1, 2013

By Zheng Wei, Jian Cheni, Zhenliang Weng, Wei Liang, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"By testing the dielectric constant and the dielectric loss factor of concentrated Dahongshan, mill scale, anthracite and light-burned dolomite in different frequency and temperature, and by studying the temperature-rising characteristics of the materials in the microwave field of 2.45GHz in frequency, the research in the paper shows that to reach at 1250°C under the same condition -2KW the microwave power and 30g the mass --the time concentrated Dahongshan takes is 330s, whereas the millscale is 855s and the anthracite is 820s. About the last one, the higher the temperature is, the stronger the absorptivity is. After the temperature has rose to 400°C, the anthracite's absorptivity increases dramatically. The result of the research would serve as the foundation of the further study on making direct reduced iron by microwave heating.1. IntroductionUnder the microwave fields, materials' dissipation of dielectric bodies would generate thermal effect. Therefore, the dielectric constant and the dielectric loss factor are closely related to materials' ability of absorbing microwave energy-the larger the dielectric constant and the dielectric loss factor are, the stronger the material's ability of absorbing microwave energy is, and the better the thermal effect would be[1-2]. In order to research how to make reduced iron from iron ore fines by microwave heating deeply and systematically, the test of raw materials' dielectric constants and dielectric loss factors are of the essence. What's more, because a mineral' conductivity is influenced by its components and crystal structure[3], it is necessary to study different materials' different temperature-rising characteristics; hence such studies would provide theoretical foundation of further research."

Jan 1, 2012

By Shadia J. Ikhmayies

"Nanocrystalline CdS thin films were prepared by vacuum evaporation on glass substrates at ambient temperature. The films were characterized by recording and analyzing their transmittance, X-ray diffraction (XRD) patterns, scanning electron microscope (SEM) images and Energy dispersive X-ray (EDAX) spectra. X-ray diffractograms revealed that the material is nanocrystalline with predominant cubic crystal structure and preferential orientation along (1 1 1) plane. SEM micrographs confirmed the nanostructure of the material and showed uniform and well covered surfaces. EDAX reports revealed that the films are cadmium rich and contain oxygen. The first derivative of the absorbance was used to estimate the effective bandgap energies of the nanocrystallites and the hyperbolic band model was used to estimate their radii. The results were compared with those obtained by XRD and SEM measurements.IntroductionCdS thin films are of considerable interest as they can be used in fabrication of solar cells and other opto-electronic devices. In particular, heterojunction solar cells with a narrow band gap base and wide band gap window have been investigated in an attempt to develop efficient, stable and low-cost solar cells [1]. The CdS quantum dot embedded in a glass matrix is one of the well-known quantum dot systems and its electronic and luminescent properties have been studied extensively [2].Three-dimensional confinement of carriers within the quantum dots leads to the blue shift of the optical band-gap and to modification of many properties of semiconductor material [3]. It has been argued that in these semiconductor nanoparticles the hyperbolic band model gives a better fit to the observed quantum size effect as compared to the effective mass approximation [4]."

Jan 1, 2012

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By Padmavathy Mahadevan, Samir Chefai, Eduard Guerra

"Electrocoagulation is a technique for treating wastewater streams from metallurgical plants whereby electrodes are corroded to generate gases (most notably oxygen at the anode and hydrogen at the cathode) and solid particulates which acts as substrates for coprecipitation of impurities. The performance of electrocoagulation reactors, in terms of their efficiency for removing a particular impurity, is highly dependent on several factors, most notably: the nature of the electrodes, the spacing between electrodes, the current density, the height of the electrodes, the solution flow rate, and application of periodic current reversal. Because these variables have complex interactions, in order to ensure reliable scale-up of laboratory results, experiments should be conducted under conditions that closely match those that would be employed at an industrial scale. To that end, this article describes the design and commissioning of a versatile laboratory scale electrocoagulation reactor that allows for the control of all the aforementioned variables along with the ability to measure the instantaneous spatial distribution of current within the reactor.IntroductionArsenic is often removed from metallurgical waste streams in stirred tank reactors by coprecipitating it with ferric ions as an arsenical ferrihydrite [ 1]. Electrocoagulation is an electrolytic technology that can accomplish the same task, but has not yet been widely adopted to treat metallurgical waste streams [2]. The electrocoagulation process involves the use of an external DC power supply to drive the dissolution of a relatively non-toxic metal into the wastewater stream, usually either iron or aluminum, which then largely precipitates as oxyhydroxide phases that adsorb undesired impurities [l]. At the anode, the metal is dissolved and oxygen is often evolved, lowering the local pH and enhancing metal ion solubility."

Jan 1, 2012

By Wilson Acchar, Fernando Barcelos, Luis Carlos Pereira

"Porous ceramics have been extensively investigated as structural materials for flow of fluids in many applications, such as filters for molten metals, water purification and hot gases, thermal protection systems and heat exchangers. This class of material must have two special features: high permeability and mechanical strength. However, these parameters are influenced in different ways by the processing method and the consequent cellular structure. In this work two different types of commercial ceramic filter materials are investigated. Characterization included the evaluation of the strength values as well as the permeability behavior and microstructural analyzes of the surface fracture. The results indicate that the strength values are strong dependent on the filament defects.IntroductionCeramic materials with a cellular structure have been extensively investigated as structural materials for flow of fluids applications [1-3]. Microstructural aspects such as morphology, size of the cell and the degree of interconnectedness are mainly parameters that influence the properties of these porous materials [4-6]. The most used industrial process to produce cellular ceramics for filter application is the polymeric sponge replication method. This technique consists in dipping the polymer foam into slurry containing an appropriate binder and the necessary ceramic materials, followed by a heating treatment [2,5].Mechanical properties of cellular ceramics depend basically on cell size, degree of interconnectedness and density [1,2,5,8,9]. Materials used as filters required a good strength and also permeability values. These properties are inversely proportional to each other. Higher porosity increases permeability values but decreases the strength values [1,2,5]. The objective of this work is to study the strength resistance of a commercial porous ceramic material (10, 20 and 30 ppi) based on silicon carbide."

Jan 1, 2012

By Wellington Pereira Inácio, Frederico Muylaert Margem, Artur Camposo Pereira, Sergio Neves

"Natural fibers are currently gaining attention as reinforcement of polymer composites for uses in engineering parts for automobile and building construction. In spite of environmental, economical and societal advantages, the natural lignocellulosic fibers are not as uniform in their dimension and properties as compared to synthetic. In recent works it was found that the variation in strength could be correlate to the equivalent diameters for several lignocellulosic fibers including the sisal fibers. In the present work an investigation on a possible correlation of the equivalent diameter with changes in density and elastic modulus was carried out. Precise measurements of the equivalent diameter, conducted in a profile projector, were correlated with the density and the elastic modulus by means of the Weibull statistic analysis. The results showed that an inverse correlation with the diameter also applies for both the density and the elastic modulus with a high degree of precision. SEM observation of the sisal fiber in structure and fracture aspects strongly indicate that defects and microfibril participation could be responsible for the inverse correlation.IntroductionAccording to Kalia [1], cellulose-based fibers are currently being pushed owing to their ""green"" image. Contrary to synthetic glass fiber, extensively used in our modem technology, these lignocellulosic fibers are renewable and can be incinerated at the end of the material's lifetime without adding pollution in the atmosphere moreover, the amount of CO2 released during incineration process is negligible as compared to the corresponding amount taken up by the plant throughout its lifetime. Even if an industrial processing equivalent of C02 release is added, the lignocellulosic fiber is considered neutral with respect to the emission of gases responsible for the global warming [2]."

Jan 1, 2012

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Douglas M. Matson, Rongbiao Gu, Christopher San Marchi, Anil Saigal

"Hydrogen embrittles most structural metals, although the form and magnitude of embrittlement depends on the source of the hydrogen as well as the stress in the metal. Hydrogen fuel cell systems typically store gaseous hydrogen fuel at high-pressure, which provides both a source of hydrogen and high stresses in the containment materials. Understanding and measuring the effects of hydrogen on the mechanical properties of common structural metals, especially fatigue properties, is important for safe, long-term operation of such systems. This work explores the use of thermography to efficiently and quantitatively evaluate hydrogen-assisted fatigue of type 304 austenitic stainless steel. In particular, thermographic analysis was used with rotating-beam fatigue testing and shown to provide repeatable results which are in general independent of test cycle frequency while reducing test times by several orders of magnitude. The effects of hydrogen were studied by thermally precharging fatigue test specimens in gaseous hydrogen prior to thermography-assisted fatigue testing and then compared to testing of non-charged specimens. Hydrogen-precharging increased the strength of this type 304 austenitic stainless steel and increased the fatigue life by a factor of about 50-100.IntroductionThe world is facing a severe energy and environmental challenge: how to provide competitive and clean energy for its citizens in light of an escalating global energy demand and concerns over energy supply security, climate change and local air pollution. As a carbon-free energy carrier, hydrogen provides a promising vector for storing and distributing renewable energy. Hydrogen is an important industrial gas that is used extensively in many industries. However, with growing demand for clean energy, hydrogen fuel cell systems are being developed for use in consumer products, such as fuel cell vehicles, which changes the landscape for safe design of high-pressure gaseous hydrogen systems."

Jan 1, 2012

By Donghai Li, Cheng Pan, Xuyang Liu, Xuewei Lv, Chenguang Bai

"Fine chromite ore is the common raw material to produce ferrochrome alloy through the submerged electric furnace process. The electric resistivity of fine chromite ore plays an important role in the operation efficiency because it determines the current distribution. The effect of particle size and the contact area of the particles on electric resistivity for several of chromite were investigated at room temperature, and the relationship between the electric resistivity of mixed particles and the volume fraction of lump ore to fine ore was also studied. The results shown that the electric resistivity increases with the increase of particle size, and the electric resistivity of mixture decreases with the increase of volume ratio of fine ore.IntroductionChromium is one of the most important alloying elements in manufacturing of stainless steel that used at high temperature and corrosive environment applications [I, 2]. As the raw materials to be charged into the steel, ferrochromium alloys and charge chromium are produced directly by smelting of chromite ore with the reducing agent in submerged electric arc furnace (SAF). During the process, the oxides of chromium and iron were reduced by carbon and meanwhile the electrical energy were consumed [3,4]. The ideal industrial process is to achieve high recovery level of Cr and Fe with minimal power consumption. In SAF process, the electric resistivity of charge stock has significant effect on the current distribution, which determines the heat distribution, molten bath structure and chemical reactions in the furnace. High resistance of the charge is desired to reduce the current distribution through the charge stock, thus the electrodes may insert into the charge stock with proper depth to form a high temperature arc heat source, and proper smelting can be realized[5]."

Jan 1, 2012

By W. Y. Kim, K. H. Song, K. Nakata

"The present study was carried out to evaluate the mechanical properties of friction stir welded Inconel 600/SS 400 lap joints. In this process, friction stir welding (FSW) was performed at a tool rotation speed of 200 rpm and welding speed of 100 mm1min, and argon gas was utilized to prevent surface oxidation during the welding. Application of FSW notably decreases the grain size of Inconel 600 alloy from 20 µm in the base material to 8 ~ in the stir zone. However, the grain size of SS 400 in the weld zone was slightly coarsened, when compared to the base material. Also, the hooking in the advancing side and the intermetal1ic compounds (M7C3) in the weld interface between Incone1 600 and SS 400 were well formed. These intermetallic compounds and hooking were effective to increase in mechanical properties such as tensile and peel strengths.IntroductionFriction stir welding (FSW), applicable welding process at solid state, has several advantages in defect suppression such as blow hole, segregation and cracking which mainly occurs in fusion welding [1, 2]. Notable grain refinement in the stir zone due to FSW can expect the outstanding increase in mechanical properties of the welds. In constructing the chemical and power plants, Ni base superal10ys have been used in many parts, moreover, fusion welding as construct method, such as gas tungsten arc welding, electron beam welding and laser welding, has been mainly used [3-5]. However, fusion welding has a limit in an increase in chemical and mechanical properties in the welds. Lately, Ni base superalloys to which FSW applied have been reported with notable enhancement in mechanical properties, which resulted from refined grains in the welds [6-10]. These researches showed the possibility in applying the FSW, directly."

Jan 1, 2012