Search Documents

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By William R. Opie

Considerable effort by extractive metallurgical research organizations has been devoted recently to developing pollution-free processes for treating copper sulfide concentrates. A number of hydrometallurgical processes are in various stages of development and have been subjected to economic evaluation. Although the hydrometallurgical approaches eliminate SO2 emission problems, they create objectionable effluents and residues, make precious metals recovery complex, and are not very efficient for treating chalcopyrite. Furthermore, they are consumers of considerably more energy than pyrometallurgical processes which produce blister copper that can be electrorefined to commercial grade cathodes. This paper discusses a pyrometallurgical process under development by AMAX Base Metals Research & Development, Inc. (1) The original objectives set for the process development were: 1. Sulfur control of at least 95% with elimination of fugitive emissions. 2. Copper and precious metal recoveries as good as or better than conventional processes. 3. Low capital cost. 4. Competitive operating costs 5. Use of known proven technology where applicable.

Jan 1, 1976

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By J. K. Brimacombe, I. V. Samarasekera, B. G. Thomas

"Mathematical models have been developed for the processing of static cast steel ingots and are app1ied to investigate the mechanisms for the formation of panel cracks. Panel cracking is an intermittent but persistent defect that causes affected steel ingots to be scrapped. A two-dimensional, finite-element, heat-transfer model was formulated and employed to calculate the temperature distribution in both large and small steel ingots during the various processing stages from initial casting to the start of rolling, including solidification, cooling in the mold and in air, reheating in the soaking pit, and subsequent air cooling. The stress state in the ingot arising from the calculated temperature variations was then determined. This involved the development of a transient, elasto-visco-plastic, finite element, thermal stress model, including the effects of phase transformation volume changes and kinetics creep, and temperature-dependent, mechanical properties. The results of the mathematical model predictions of temperature and stress were then used to determine the mechanisms and to suggest solutions for two different types of panel crack formation. Mid-face panel cracks apparently form during air cooling when the mid-face surface temperature is between the Arl and 500~C. Off-corner panel cracks appear to initiate internally during the early stages of reheating but do not propagate to the surface until much later. IntroductionPanel crack formation in static-cast steel ingots is a defect that has been plaguing the steel industry for several decades. Although the problem is intermittent, it is also serious since affected ingots must be scrapped. Panel cracks are manifested as two distinct types of cracking problems. ""Mid-face"" panel cracks are found exclusively in small, 2 to 6 ton, medium carbon steel (0.3 to 0.7% C) ingots and usually exhibit a single, continuous, longitudinal crack down the center of one of the ingot faces as shown in Fig. l (l). ""Off-corner"" panel cracks often form roughly oval, discontinuous crack patterns on the wide faces of large, 20 to 30 ton ingots as seen in Fig. 2 (2). They affect only low carbon steels (0. l to 0.2% C) with high manganese content. Both defects affect only aluminum-treated steels and are caused by a combination of intermediate temperature ductility loss involving aluminum-nitride precipitation and thermal stress generation. The ductility problem has received a good deal of attention which was the subject of a recent review (3). The present study was undertaken to investigate the thermal stress aspects of the problem through the development of mathematical models of heat transfer and stress generation in static-cast steel ingots. The ultimate objective was to elucidate the mechanisms of formation for both types of panel crack and to evaluate possible solutions to the problem."

Jan 1, 1986

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By Dhanesh Chandra

Long term stability studies were conducted on four variants of LaNi5; 10,000 hydriding/dehydriding cycles were used to evaluate their suitability for a metal hydride cooling system. Thermodynamic and structural studies were conducted to determine changes in these materials during cycling test period. The hydrogen sorption properties of LaNi5.2, and Lao 9Gd0.1Ni5 and LaNi4.75In0.27 were seriously degraded during the tests but the LaNi4.8Sn0.22 hydride was virtually unaffected. Hydride isotherms were measured at the beginning and at intervals through out the test period to observe the nature and extent of damage degradation in the sorption properties. X-ray diffraction studies of the alloys (LaNi5.2, LaO.9Gd0.1Ni5 LaNi4 8Sn0.22) and their respective hydride, before and after test, provided insight with regards to the observed changes in the hydride properties. Electron microscopic studies were also conducted to evaluate the changes in particle sizes.

Jan 1, 1989

By John E. Dutrizac, Tzong T. Chen

"Laboratory experiments were undertaken to ascertain the behaviour of various ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C and in the presence of 40 or 50 g/L of hematite seed. Copper, nickel and zinc are not significantly incorporated in hematite precipitates. Although the nickel contents increase to 0.22% as the Ni concentration increases to 60 g/L, the solid solution Ni contents are low relative to the bulk Ni contents. Thus, part of the Ni may be present as tiny particles of poorly soluble NiS04.H20. Increasing germanium concentrations to 2,000 mg/L result in products containing up to 0.59% Ge. The Ge occurs either in solid solution in the hematite or is adsorbed on the nanometer-size hematite crystallites. Increasing As(V) concentrations to 10 g/L increase the AsO4 contents of the products up to 16%. However, the products consist of hematite together with As04-containing Fe(SO4)(OH) and an unknown Fe-AsO4 species. All the hematite products contain - 1% SO4 which appears to be adsorbed on the nanometer-size hematite crystallites.IntroductionDissolved iron is a common impurity in most hydrometallurgical processing circuits and, generally, the iron must be eliminated prior to the subsequent recovery of the sought after metals. Simple neutralization of iron-rich solutions yields slurries which are difficult to thicken and filter. To address these concerns, the jarosite, goethite and hematite processes have been developed, and these technologies are able to reject the dissolved iron in a readily filterable form [1]. Despite its higher cost, the hematite process offers several potential advantages. Because hematite is an iron-rich, high-density compound, its formation would reduce the mass of residue and the size of a residue storage pond. Hematite is the thermodynamically stable form of iron under ambient conditions, and this stability would facilitate the impoundment of hematite precipitates. Furthermore, hematite has some market potential for cement manufacture and even for iron making [2]. In all the commercial hematite processes, the dissolved ferric ions are first reduced to the ferrous state. Subsequently, the pH of the solution is adjusted and the solution is then oxidized. The ferric ions gradually generated during solution oxidation hydrolyze and precipitate mostly as hematite, although commercial hematite products also contain trace or minor amounts of jarosite-type compounds. However, there are potential advantages in precipitating hematite directly from ferric ion solutions, as the reduction and subsequent oxidation of the iron are not required. Although the precipitation of hematite directly from relatively concentrated ferric sulphate solutions (up to 0.5 M Fe(SO4)is) was recently demonstrated [3], the behaviour of impurity species during hematite precipitation is largely unknown. To address this issue, systematic laboratory experiments were undertaken to ascertain the behaviour of a number of ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C, and the results are presented in this paper."

Jan 1, 2012

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By M. E. Myers

An experimental program is being carried out to determine the thermodynamic characteristics of zinc solubilization in high-temperature iron and iron-carbon alloys. Two versions of an isopiestic technique are being used, with zinc at a lower temperature being equilibrated with pure iron foils or molten iron-carbon alloys at a higher one. The lower temperature sets the partial pressure of zinc vapor, and thus the activity relative to a given reference state. Initial results show Henrian behavior for dilute zinc solutions in austenite and a molten 4.6% C alloy, with unit-pressure solubilities in pure Fe that closely match the predictions of Wriedt.

Jan 1, 1992

By P. Klut, D. Groult, R. Marechalle, B. T. H. Bonnema

In the past 5 years, Compagnie Europeenne de Dezingage (CED) has developed a successful dezincing process and the St. Saulve pilot plant has evolved into a commercially successful production plant. Currently the plant meets all the required standards for scrap and zinc quality, output capacity, availability, and meets the prescribed environmental emissions standards. The initial process problems relating to zinc recovery, uncontrollable explosions and sodium hydroxide aerosol emissions have all been solved. Presntly, the yearly production of dezinced scrap is around 50.000 tonnes/year; this capacity is enough to supply the local market. This capacity can be increased easily to 65.000 tonnes/year or more. The market for dezinced material is growing due to the increased consumption of galvanized material on one hand and on the other hand the higher demand for high quality scrap. The proven technology of CED is currently patented worldwide, but CED is inviting licensees to implement the dezincing technology in other parts of the world.

Jan 1, 2000

By Jonkion M. Font

As a comprehensive contribution to the understanding of oxygen-blowing of matte smelting, the copper and nickel solubilities between the FeOx SiO2-MgO slag with saturated SiO2 and the Cu2S-Ni3S2 FeS matte with the NCu/(NcU+NNi) of 1, 0.75, 0.5, 0.25 and 0, in a MgO crucible were investigated at 1573 K under controlled partial pressures of SO2 at 0.1, 0.5 and 1 atm. The partial pressures of SO2, S2 and O2 were controlled by using an Ar-SO2-S2 gas mixture after passing through a sulfur reservoir. It was clarified that, at a given matte grade, the solubility of copper in the slag was independent of pso2 while that of nickel increased with increasing pso2. This notable difference was considered to be ascribable to the chemical formulas of the mono-metallic sulfides in which one copper atom combines with ½ sulfur atom while one nickel atom combines with 2/3 sulfur atom. It was also clarified that, at a given iron content in the matte, the pot and ps2 were independent of the matte species. This was ascribable to aFeS in the matte, which was independent of the matte composition, Ncu/(Ncu+NNi), at a given iron content in the matte.

Jan 1, 1999

By K. Soldenhoff

The Bulong deposit, situated near Kalgoorlie in Western Australia and owned by Resolute Limited, is a lateritic deposit containing on average 1.1% nickel and 0.09% cobalt. A process has been developed and tested at the mini-plant scale for direct solvent extraction and separation of Co and Ni from solutions derived by acid pressure leaching of Bulong ore. In this paper, two solvent extraction processes are described. The first process uses Cyanex 272 to extract cobalt and reject nickel to the raffinate. The second process uses Versatic 10 to extract and purify nickel. The loaded strip nickel solution is suitable for electrowinning. Results of both batch laboratory tests and continuous mini-plant trials are presented. The selectivity of the solvents with respect to the major impurities such as Mn, Mg, Ca, and Zn is also discussed.

Jan 1, 1998

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016

By G. A. Irons, G. S. Hanumanth

A three-dimensional mathematical model for the electric furnace of Cominco's Kivcet process was developed to compute the electric field intensity, power dissipation, temperature and velocity distributions in the furnace. A number of simulations of the electric furnace operation were carried out for various electrode immersion depths and electrode currents. The results showed that the current penetrated the bullion layer, generating high current densities in a layer approximately 0.3 m thick located in the slag/bullion interface region. An increase in the electrode immersion depth increased the furnace power as well as slag temperatures, and generated more vigorous bubble stirring and thermal homogeneity in the slag. For a given applied current, the computed power was in reasonable accord with the measured power input. The calculated temperatures were in rough agreement with the tapping temperatures of slag and bullion.

Jan 1, 2000