Search Documents

By Scott A. Shuey

Keywords: E-Waste, Pyrometallurgy Many might think addressing the issue of e-waste is a new area of study. Electronics disposal has been discussed in some circles for at least the past 25 years. The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of ?electronics.? Focusing only on the primary constituents (polymers, Cu, Al, Fe, etc.) tends to lead one to fairly simple flowsheets. Ignoring trace elements, and the various halide species generated, will lead process engineers down a development path that is sure to cause material handling issues. Researchers at Colorado School of Mines are modeling the complex chemistry that exists within the body of e-waste?comprising 39 of the known elements. An understanding of the systems thermodynamic behavior will result in the development of a more robust, long-term process for the recovery of valuable materials from the e-waste stream.

Jan 1, 2005

By Jerry D. St. Clair

A multidisciplinary team of scientists and engineers at Wont has been working to understand heavy metal contamination of DuPont process waste streams and technologies for abatement of these metals. As part of this effort, an extensive study was made of a specific waste stream of importance in DuPont's environmental commitment. This 200 gpm stream contains 5-5000 ppm of nickel plus a variety of inorganic and organic constituents. The chemical complexity of the waste rendered conventional. alkaline precipitation ineffective, and only through the simultaneous application of analytical characterization, fundamental chemical understanding, and process engineering did effective technical approaches emerge. In this instance, ion exchange, sulfide precipitation, and caustic digestion ultimately proved successful in reducing the nickel to below the 1 ppm target. The results of this study will be presented, along with key learnings about the process of solving heavy metal contamination problems.

Jan 1, 1994

By Xuemei Zheng, Aiyuan Ma, Chao Liu, Guojiang Li, Chenyu Sun, Jinhui Peng, Libo Zhang, Yongguang Luo

In this paper, the removal of fluorides and chlorides from blast furnace dusts by water vapor enhanced microwave roasting was investigated, combined with the advantages of microwave selective heating and based on a thermodynamic analysis of zinc and lead halides. According to proposed reactions in the process, detailed experiments were systematically conducted to study the effect of roasting temperature, holding time, air flow, water vapor flow rates, and stirring speed on the efficiency of the removal of F and Cl. The results show that 97.26% of F and 64.23% of Cl could be separated when the condition of the roasting temperature of 650°C, stirring speed of 80 rpm, holding time at 60 min, air flow of 350 L/h and water vapor flow rate of 8 mL/min was optimized.

Jan 1, 2016

By Henry Hu

In high pressure die casting processes, proper control of temperature die yields a high casting production rate and superior quality components, Die temperature is usually influenced by various die design and process parameters such as size and location of intemal water cooling lines, flow rates of cooling lines, and pouring temperature of molten metal. Among them, the cooling water flow rate plays a major role in controlling thermal pattern of the die_ In order to develop an effective control strategy, data of local die temperature must be collected and analyzed, In this study, a PC-based data acquisition and control system (DACS) for die temperature control has been designed, and established, The developed DACS has three input channels for temperature signals and one input channel for water flow rate signals, as well as one output channel for a water pump, and is capable of displaying data in both curve format and value format. Implementation of the DACS in a laboratory setup has also been attempted, It should be pointed out that more advanced control mechanisms can be potentially integrated into this system in future,

Jan 1, 2003

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By E. James Quinn

Solvent extraction technology using EHEHPA (2-ethylhexyl phosphonic acid, 2-ethyhexyl mono ester) is the norm for industrial separations of rare earth elements. This process has some shortcomings, including a large number of stages compared to most SX processes and high acid requirement for stripping of the heavy rare earths. In this work, we examine a number of alternative mixed solvent extraction systems: (i) Mixtures of organophosphonic and phosphinic acids such as EHEHPA/Cyanex 272 or Cyanex 572; (ii) Ionic liquid mixtures of EHEHPA with quaternary ammonium chloride (Aliquat 336); and (iii) Mixtures of carboxylic acids for yttrium/lanthanide separations. We discuss and compare the efficacy of these systems with reference to the Nd/Sm separation, which is of industrial significance. Based on the extraction chemistry and the use of modelling tools to define the counter-current solvent extraction circuit, we present a techno-economic analysis of a separation plant and discuss the impact of various solvent systems on the capital expenditure (CAPEX) and operating costs (OPEX).

The mineralogy of the platinum group metals is fairly complex, and it is therefore not surprising that the different minerals have variable responses to metallurgical processes, in particular, flotation and leaching. The PLATSOL® leach process was developed to extract simultaneously base metals, gold and platinum group metals from various materials. Extensive research has indicated that most PGM?s were amenable to the PLATSOL process, with the notable exception of cooperite PtS. Further work showed that a thermal pretreatment at 500-700ºC transformed the structure of the cooperite and similar refractory minerals (Pt,Pd)S into Pt metal and Pt-Pd alloys that responded well to the PLATSOL® process. Examples are presented of the mineralogy of PGM concentrates as produced, in the residue from the PLATSOL® leach and after thermal pretreatment.

Jan 1, 2006

By T. Nagano

Mitsubishi Metal Corporation started the development work of a new process for continuous production of copper in 1961. After a series of experimental and semi-commercial operations, the first commercial plant of the Mitsubishi Continuous Copper Smelting and Converting Process was put into operation in March, 1974. The new plant, which has a design capacity of 4,000 metric ton copper per month, was built within the premises of Naoshima Smelter, replacing the old No.1 reverberatory smelter there. The SO2-rich exhaust gas from this new plant is blended with the off-gas of the No.2 reverberatory furnace for production of sulfuric acid and the overall emission of sulfur at Naoshima has been greatly reduced. The operation of the continuous plant has been satisfactory and several advantageous features of the Mitsubishi Process have been proven on a commercial scale. This paper first gives a brief description of the history of the development work and the characteristic features of the process. The paper then describes the new commercial plant and operating data obtained so far.

Jan 1, 1976

By C. Ek

In bismuth metallurgy, low-copper high-sodium mattes are by-produced. Different charges containing mixtures- of crude mattes, oxidized matte, and/or copper sulfide concentrate and/or copper silicate ore have been smelted to give a rich matte and a disposable slag, then converted to obtain blister copper with high recovery and a rich slag to be recycled.

Jan 1, 1983

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920's with in situ operations in the underground mine and small dumps up to the 1950's. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased' to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999

By Toshiki Kabutomori

In fuel cell powered automobiles, hydrogen is required to be stored in materials that have a hydrogen storage density of over 4 mass%; further, these materials should be capable of supplying hydrogen by using the waste heat from a fuel cell, which is at a temperature of 373 K, in order to match the mileage of gasoline-powered vehicles. A Ti-Cr-V alloy, which exhibits a BCC structure and forms a solid solution, is a promising candidate for onboard hydrogen storage materials. Although it has a large hydrogen storage capacity of over 3.9 mass%, the rechargeable hydrogen capacity is limited to approximately 2.6 mass%. In this study, the effects of fine pulverization of the alloy on PCT (hydrogen pressure-composition-isotherm) characteristics were investigated in order to improve the rechargeable hydrogen storage capacity of the alloy. From the PCT measurements of the finely pulverized samples of the alloy, a plateau in the absorption curve was observed to begin at a hydrogen concentration of 0.5 mass%; further, a rechargeable hydrogen storage capacity of 3.3 mass% was obtained. This was greater than that obtained from the sample that was not finely pulverized, i.e., 2.5 mass%. However, the plateau width in the desorption curve was 2.5 mass%, which was the same as that observed for the sample that was not finely pulverized. The increase in the rechargeable hydrogen capacity during absorption is attributed to the precipitation of the -hydride phase (MH~2) directly from the metal phase (phase). The precipitation of the phase (MH~0.5), which should be formed in low hydrogen concentrations, is suppressed as a result of a possible reduction in the internal defects such as dislocations, vacancies, and grain boundaries by fine pulverization and annealing of the alloy.

Jan 1, 2006

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By R. G. Reddy

The oxidation kinetics of A13Ti intermetallics have been studied at the temperature range of 850°C to 100O0C in pure dry oxygen. The oxygen diffusion rates were investigated using TGA method. Parabolic rate constants were calculated. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction. A continuous A120, scales with a little TiO2(rutile) were formed on the intermetallic surface. The A13Ti intermetallic exhibited excellent oxidation resistance among the Ti-Al base intermetallics.

Jan 1, 1997

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By Sylvain Gouttebroze, Mohammed M'Hamdi

In a previous work, a small scale Bridgman furnace has been used to study silicon bi-grain crystallization at different cooling rate. This work expands the analysis by studying the mechanical interaction between the crucible and ingot during the solidification and cooling. The thermal model is based on a 2D-axisymetric heat-transfer model. The flux histories are then transferred to the ingot-crucible 3D-model. Anisotropic Elastic and Crystal Plasticity model are used to model the silicon deformation. Four different assumptions are applied to model the mechanical contact crucible-ingot and three grain misorientations are considered. The results show the strong impact of the alumina crucible contraction on the stresses and deformations in the silicon ingot.

Jan 1, 2015

By S. N. Lekakh

Phosphorous segregated at grain boundaries during solidification and heat treatment dramatically decreases low temperature toughness of precipitation hardened Fe-Mn-Al-C austenitic steel. A thermodynamic analysis was performed to evaluate the possibility of decreasing P and subsequent segregation by Ca- and Ce-additives in the melt. It was shown that the predicted probability of forming a P containing compounds depends on melt composition and treatment sequence. Experimental heats were performed and several micro- and macro-structural effects of Ca- and Ce-additives were recognized by using an automated inclusion analysis technique.

Jan 1, 2010

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005