Search Documents

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By Bowen Li, Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"Magnetic iron sulfide ore particles heat rapidly by microwave (MW) irradiation generating plasma during oxidation of surfaces. The high temperatures produced by the exothermic event decompose local portions of samples forming a differentiated flux of partially melted silicate (si-mt) with entrained metal-sulfide (sul-mt) droplets. The si-mt forms crystals of olivine (01) in Ca-rich pyroxene (Cpx) melt that resorbs a portion of iron sulfide (Po). The immiscible sul-mt droplets of (Fe,Ni,Cu)1-xS contain magnetic subsolidus Ni-pyrrhotite (Ni-Po) with Cr-bearing ferrospinel (Mag). Sub-micron sized flecks of Au are found on the surface of a sul-mt droplet with scanning electron microscope (SEM).IntroductionSulfide ore deposits supply the world's mineral resource in the production of non-ferrous metals. Particularly, Cu-Ni deposits are chemically enriched in metals from high sulfur saturation during magmatic formation that creates the proper geochemical environment for metals enrichment [1, 2]. The sulfur and oxygen fugacity control redox conditions of a differentiated silicate/sulfur magmatic melt with the concentration of iron playing a dominate role in the chemical partitioning of metals in sulfide liquid [3, 4]. The initial magnetic crystallization of (Fe,Ni)i-xS monosulfide solution (mss) from metal-sulfide liquid has an exclusive effect on the fractionation of mineral assemblages (zoning) [5].Phase equilibria of sulfide melt (sul-mt) components are related by a miscibility gap with mss forming Ni-rich pyrrhotite (Ni-Po) followed by the crystallization of (Fe,Cu)1-xS intermediate sulfide solution (iss) [6]. Precious metals form stable chacogenides and are retained in solution until the final liquid solidifies. The redistribution of metals now occurs by subsolidus cooling of mss and iss that exsolve low-temperature Fe-Cu-Ni bearing mineral assemblages [7]. The proper interpretation of ore genesis increases processing capabilities by isolating chemically enriched zones during extraction and should be used to aid in sustainable mine site development [8-11]."

Jan 1, 2013

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By R. D. Osmanson

A series of batch roasting tests was performed on minus 1/2 inch gold bearing refractory samples from the Gold Acres deposit, and 67 select particles were polished and the sulfide alterations were examined microscopically. The suite of specimens represents two hour batch roast treatments at 600°C, 700°C, 725°C, 750°c, 800°C, and 900°C. Auriferous pyrites were found to alter sequencially to pyrrhotite, magnetite and finally to hematite. It was found that the decrease in cyanidation extraction with high temperature roasting is likely due to the increas ing stability of magnetite and more crystalline hematite, and the decrease in porosity with these phases which occlude the gold. Gold has been noted to occur very early in the mineralizing sequence, with gold being found in quartz and in clay/carbonate rock matrix. No gold was found in the two pyrite phases, but numerous gold grains were found in pyrrhotite after pyrite and in subsequent iron oxides. Gold mineralization had apparently ended by the time base metals were introduced into the deposit.

Jan 1, 1987

By James Douglas

A century ago the AIME meeting of 1899 was held at the Palace Hotel in San Francisco California in September. For his presidential address, James Douglas presented this paper which is reprinted in full with the kind permission of the AIME. It presents an interesting comparison relating to events and circumstances in the metallurgical industries at the close of last century. Being on the eve of a new century ourselves, the Editors of this volume of the COPPER 99-COBRE 99 Proceedings considered this paper would be of general interest, hence it is included here. Douglas believed in effective interchange of technical experiences and ideas. He considered the extreme secrecy surrounding the copper works at Swansea, Wales, the world center of copper only years before the time his paper was delivered, as one key reason for its decline, (and eventual closure of all copper plants there). In his paper, the pace of developments in various sectors such as transportation (railroads, the dominant means of I transportation at the time), the iron and steel and copper industries were examined, in much the same way as one might do but on the high technology of today. James Douglas was born in Quebec City, Quebec, Canada and spent his early life there. Forced to move to the United States for family and financial reasons, he went on to become a pioneer in the new Arizona copper industry, and with luck and good judgement with his interest in the new mining properties he also became very wealthy. Douglas was an accomplished mining and metallurgical engineer. He was the first President of Phelps Dodge and helped transform the small trading company of Anson Phelps and William Dodge into a mining giant.

Jan 1, 1999

By R. Angulo

Carbon nanotubes (CNTs) have recently emerged as materials with outstanding properties. This has promoted their consideration as reinforcements for other material systems, such as ceramics. However, one of the fundamental problems with producing CNT-reinforced ceramics is the effective dispersion of CNTs during processing. This has been successfully carried out recently using organic solvents. This paper is a preliminery investigation into the rheological behavior of aqueous CNT-alumina slips, with the objective of moving towards a more environmentally friendly aqueous tape casting process for the production of CNT-ceramic composites.

Jan 1, 2008

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk's present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By Shengli Wu, Juan Zhu, Wei Huang, Xinliang Liu, Kaiping Du, Kaifa Zhang

Based on the furnace burden of high content of Al2O3, the process of softening and melting and the characteristic of primary slag were studied with the increase of MgO content in the sinter and adding some MgO into the pellet. The results showed that the content of MgO in the primary slag increased with the increase of MgO in the sinter and pellet. Meanwhile, the permeability of the furnace burden was improved because of low viscosity of high MgO primary slag. Compared with the increase of MgO content in the sinter, the increase of MgO content in the pellet can improved the softening and melting characteristic of the comprehensive furnace burden more effectively. More Mg-bearing pellet should be chosen in the comprehensive furnace burden for the purpose of improvement the fluidity of primary slag and the permeability of the furnace burden in the burden of high Al2O3 content.

Jan 1, 2015

By Do-Hyeong Kim, Tae-Jung Kim, Seung-Yeon Won, Jong-Jin Pak, Min-Kyu Paek

Liquid iron alloys containing V, Mo, and Ni can be produced by the carbothermic reduction of spent catalysts used in petrochemical industry. Thermodynamics of carbon in these alloy melts is important for refining these alloys. In the present study, the carbon solubility in Fe-V, Fe-Mo, Fe-Ni, Fe-V-Mo, Fe-V-Ni, Fe-Mo-Ni and Fe-V-Mo-Ni alloy melts of various compositions was measured at 1873 K. The temperature dependency of vanadium effect on carbon solubility in liquid iron was also measured in the temperature range from 1823K to 1923K. The additions of vanadium and molybdenum significantly increased the carbon solubility in liquid iron alloys while nickel decreased the solubility. The experimental results were thermodynamically analyzed using Lupis’ relation at constant activity to determine the first- and the second-order interaction parameters of vanadium, nickel and molybdenum on carbon at carbon saturated condition. Using thermodynamic parameters determined in the present study, the carbon solubility in Fe-V-Mo-Ni alloy melts of various composition were accurately predicted and verified experimentally at 1873 K.

Jan 1, 2014

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By Guo Chen, Xuefeng Liao, Tu Hu, Shengzhou Zhang, Hongying Xia, Jinhui Peng, Libo Zhang

Pine nut shell is as raw material for preparation of high surface area activated carbon (HSAAC) by microwave induced KOH activation. The effects of microwave power, activation duration and KOH/C mass rate (R) on the iodine adsorption capability and activated carbon yield were investigated. Additionally the surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms and SEM. The operating variables were optimized utilizing the response surface methodology and were identified microwave power 738W, activation duration 17 min, and R 4, corresponding to a yield of 46.28 % and an iodine number of 2154 mg/g. The key pore structure parameters of HSAAC such as the Brunauer–Emmett–Teller (BET) surface area and total pore volume were estimated to be 3819 m2/g and 2.09 mL/g, respectively. The findings strongly support the feasibility of microwave heating for preparation of HSAAC from spent pine nut shell by microwave induced KOH activation.

Jan 1, 2016

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Xiang Zhu

Xidagou is the largest waste water discharge channel of the Anshan Iron and Steel Complex (AISC) with average flow rate of 8000 cubic meters per hour, which is about 75% of the total effluent of the AISC. The waste water from Xidagou seriously polluted the Taizi River Basin. In order to meet the Chinese Class V Standard for Surface Water Discharge and the Standard for Recycled Industrial Water Reuse, with the aid of the World Bank, the AISC began the treatability studies in 1991. Based on the bench-scale test, the AISC carried out pilot-scale treatability studies on three different treatment processes and five different chemical coagulants for more than half a year in 1992. The study results show that the processes of primary sedimentation- chemical mixing and flocculation-secondary sedimentation-filtration can meet the requirement and that PFS and PAM are effective and economic chemical coagulants.

Jan 1, 1994

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By J. Y. Hwang

Microwave heating is an attractive alternative to conventional heating methods because heat is generated directly within the microwave absorbing materials. It has potential to be utilized for selective heating and removal of specified components from a materials mixture. This investigation was undertaken to explore the potential of selective heating and burning of binders for foundry sand reclamation. Selected raw materials and binders used in foundry operations were tested to determine their receptivity to microwave heating. Time needed to reach 600°C and/or the maximum temperature achieved for samples irradiated by microwaves for twenty minutes under 800 W microwave power are reported. The microwave heating characteristics of the selected materials are summarized and discussed. The interactions between microwaves and the raw materials used in a foundry. such as silica sand. chromite sand and bentonite (clay) binder were studied. The results showed that chromite sand coupled well with microwave energy at ambient temperature while silica sand did not. This was expected because the major component of chromite sand. iron chromite (FeCr2O4). is a good microwave absorber. while quartz, which is the major component of silica sand, is a microwave transparent material at ambient temperature. Bentonite absorbs microwaves well because it contains a hydroxyl functional group and water molecules in its structure. It was found that the structure of bentonite was changed through microwave irradiation. Microwave heating characteristics of silica sand mixed with different amounts of bentonite binders were investigated. The presence of bentonite in the mixture improved the microwave heating of silica sand significantly. and bentonite was deactivated by the microwave processing.

Jan 1, 1995

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By Jose Bengoa

Low metal prices and environmental restrictions are always a challenge for copper smelters operation and its productivity. Thus, in order to reduce production costs and control gas emissions, improvements of the Teniente Converter (CT) operation were made at 110 Smelter Plant of Southern Peru Copper Co" 110, Peru, and the main objective was to increase its capacity for smelting copper concentrates without affecting normal operation, The present work eorresponds to a recent study conducted during the normal industrial operation of the Teniente Converter in this plant and, it shows the effect of increasing air oxygen enrichment from 28 to 34% on its productivity. The results show an increasing of concentrate smelting rate from 800 to 1370 tpd and hence a notorious improving in copper production, and practically no effect on the refractory consumption. The increment of the concentrate throughput, increases also the SO2 concentration and the sulfuric acid production, showing the effort done by this operation in order to accomplish the environmental Peruvian regulation,

Jan 1, 2003