Search Documents

Effective strata control, utilising fully encapsulated roof bolts, is dependent on the installed quality of the reinforcement elements. One mechanism by which fully encapsulated roof bolts may become less than fully effective is by gloving (glove fingering) and un-mixing of the resin. Following some small roof failures containing gloved bolts, investigations have been undertaken in some New Zealand coal mines to determine the extent of, and mechanisms involved in, the gloving of fully encapsulated roof bolts for a range of roof types and installation methods. Gloving, in this context, refers to the resin cartridge partially or completely enveloping a length of the bolt, typically with unmixed resin filler and catalyst/hardener remaining within the cartridge. Results have shown that gloving and un-mixing is a systematic and widespread phenomena, occurring across a range of resin and/or bolt manufacturers, and across a variety of roof types. Gloving was found in bolts installed using: hand held pneumatic and continuous miner mounted hydraulic methods, under run of mine (ROM) conditions by mine workers, and under controlled "best practice" conditions. The roofs bolts investigated are all 1800mm (6ft) long, and have shown that, on average, 485mm (-19") of the bolt length is gloved and/or unmixed. This equates to a 27 percent reduction in effective bolt length. The effected length of bolt is sufficient to impact on the load transfer/reinforcement capabilities of the bolt system, and hence impacts on the design assumptions and subsequent stability assessments. Furthermore, there is a direct relationship between the mechanism for the gloving of bolts and an increased occurrence of resin loss and reduction in encapsulations length in soft (less than 10 MPa) and/or highly fractured rock. Investigations have concentrated on developing an understanding of the mechanisms involved. This has been undertaken using both field installations and recovered bolts, as well as test bench trials. The mechanisms involved have been confirmed as being: the development of a pressure front as the bolt encounters the resin and is spun up the hole, which, in turn, leads to over-pressurisation and radial expansion of the resin cartridge, resulting in an increase in diameter of the plastic resin cartridge, which allows the bolt to be spun up into the cartridge without making sufficient contact to shred the cartridge or the hardener tube, resulting in an unmixed portion of resin.

Jan 1, 2003

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By Andrew Hyett

Over the last 30 years, a transition away from end-anchored bolts to fully grouted rock bolt systems has occurred in many underground mines. It seems geomechanically intuitive that the success of such bolts, which interfere with rock movements around underground excavations through a variety of complex interactions, is precisely why they remain challenging to instrument and monitor. Whereas measuring the load profile for an end-anchored mechanical bolt is trivial, for a fully grouted system, the load may vary dramatically due to discrete rock movement at cracks and joints. Despite the challenges, measuring the strain (i.e., load) along fully grouted rock bolts remains very appealing, and a lot of valuable research has been conducted using foil resistance strain gauges, particularly in US coal mines (Signer and Jones, 1990). Despite good intentions, more widespread adoption of this instrumentation remains unlikely for the following reasons: (i) The technology is expensive, partly because Intrinsically Safe (IS) requirements limit the number of suppliers and solutions. (ii) The technology is perceived as challenging to successfully implement except by those who are skilled in the art. (iii) The reliability of the technology is questionable in harsh environments. (iv) The technology relies on discrete pairs of strain gauges that may not capture the complete strain distribution along the bolt. No existing alternative technology can offer a solution to all of these limitations. However, in this paper, we introduce results from a new Distributed Optical Sensing technology that promises significant potential. Since the technology is capable of distributed sensing, our results suggest that this new technology can, for the first time, reveal the detailed strain profile along fully grouted rock bolts.

Jan 1, 2013

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015

By Bruce W. King, David A. Newman

"Underground mines have always been an integral part of the limestone industry. However, beginning in the 1990s, the number of underground limestone mines has increased for many reasons including• Stripping ratios at surface quarries have become uneconomic.• Existing surface quarries have reached the mineral boundaries, and the remaining stone reserves are underground.• Surface access to the entirety of the limestone reserve is limited by development or infrastructure.• The once-rural setting of the surface quarry is now surrounded by subdivisions and development. An underground mine is less intrusive and takes the mining operation out of the public eye.• For larger markets, an underground mine enables year-round production without the sequence of overburden stripping in the winter to expose mineable stone for summer production. This is common at many surface quarries.Multiple-level operations are a natural extension of the decision to mine underground. Most limestone reserves, for example, the Tyrone-Oregon-Camp Nelson, Hermitage-CartersLebanon- Ridley, and Salem Limestones, are sufficiently thick to accommodate multiple levels. Multiple-level mines should be planned by considering each level separately and then integrating the individual levels into a larger mine plan. Failure to plan all the levels of a multiple-level mine in concert can result in ground control (back, pillar, floor, and inter-level sill pillar) problems attributable to stress transfer and interaction between the levels or the necessity to leave a thicker sill pillar between adjacent levels.Multiple-level mine planning begins with geology. Once the upper level back horizon is identified, the geology, rock strength, and physical properties in each level are used to• identify the optimal back horizon• quantify whether back support is required and, if so, the type, spacing, and length of the back support• determine the pillar centers• determine the total mining height, including floor shots"

Jan 1, 2016

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By T. J. McMahon

This Bureau of Mines study describes the development of a large-scale, three-dimensional, finite-element model of a deep-vein Coeur d?Alene District mine. The three-dimensional model was prepared from combined digitized mine maps and generated levels that may also be analyzed as independent two-dimensional models. A comparison of the stress changes and displacements was made following a simulated vein excavation in both the three-dimensional and two-dimensional models. A one-cut excavation was simulated with the two-dimensional model and a multiple-cut excavation was simulated with the three-dimensional model. The compared results from the two analyses are discussed in terms of the inherent differences between the models.

Jan 1, 1989

By Anthony Spearing

There are approximately 68 million rockbolts installed annually in underground coal mines in the USA (Tadolini and Mazzoni, 2006). The most utilized is the passive fully grouted resin rebar bolt, which constitutes almost 90% of the primary support in US underground coal mines. Resin-grouted rockbolts are a very effective and safe support, but their performance still needs to be further optimized and improved. This paper investigates their performance and suggests operating conditions to optimize the performance of resin-grouted rockbolts. In addition, this paper discusses a small-scale test that can also be used to evaluate the performance of rockbolts that is quicker, easier, and less costly than short encapsulation tests.

Jan 1, 2014

By David C. Johnson

Coal mining in Illinois has resulted in many structures being exposed to subsidence damage. Damage mitigation techniques (DMT) applied in the foundation design/construction have proven successful in minimizing damage in several test cases. To determine the practicality of these techniques, the Costs of their application are investigated. The AMT costs are compared to foundation and total house costs for various classes and sizes of houses. An economical and effective subsidence resistant foundation construction is proposed.

Jan 1, 1993

By L. Munsamy

The bulk of primary mining at the Anglo Coal's Bank Colliery was carried out by drill and blast method, in a bord and pillar layout exploiting the No. 2 Seam. Secondary extraction, top/bottom coaling, also took place using both the drill and blast (D&B) method and continuous miners (CM). Extensive mining in this seam resulted in the risk of sterilising the No. 4 Seam reserves. Therefore, multiseam design guidelines established by Salamon and Oravecz (8) were re-evaluated in light of the low safety factors and the low pillar width to mining height ratios of pillars in the No. 2 Seam. Two and three dimensional (2D & 3D) numerical modelling was carried out to quantify and verify the parameters that influence the multiseam mining. The modelling was conducted primarily in two dimensions (plane strain), with 3D models to confirm the validity of the 2D results. A panel risk assessment flow chart was developed to assess the panels with respect to pillar failure and multiseam mining. This flow chart was extended into the evaluation of risk of surface subsidence using the current rock engineering knowledge. The aim of this risk assessment tool is to assess all underground workings at Anglo Coal collieries simply and rapidly. The identification of high-risk areas would warrant further investigation and possible backfilling to reduce the risk of pillar failures ensuring that reserves in the No. 4 and 5 Seams above are intact.

Jan 1, 2004

By Stephen Tadolini

Reduction in the time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. While this concept is not without controversy and risk, the rewards can result in substantial reductions in longwall face move/set-up times and provide safer working conditions. Both of these factors can reduce mining costs and enhance profitability in a competitive market. This project was even more complex because the longwall system operates under a weak roof condition. To examine the feasibility of this concept, a 16-ft wide by 170-ft long experimental pre-driven recovery room was designed using analytical, empirical and 3-dimensional finite element modeling techniques. Based on the projected loading conditions, immediate and main roof geological and strength characteristics, a variety of roof bolt types were selected and installed in the recovery room and adjacent chutes. To supplement the intrinsic supports, high-capacity roof-to¬floor cuttable cribs were strategically placed to reduce the potential of a weighting failure before the longwall shields safely entered the room. To evaluate the behavior and final support performance, the recovery room and chutes were instrumented to monitor the physical response during various loading phases. Additionally, the cuttable cribs were instrumented to evaluate the loading and stiffness characteristics during the extraction process. This paper describes the successful design process, support methodology, monitoring results, final observations and recommendations.

Jan 1, 2002

By George B. Quaye

Conventionally, roadways in South African collieries are 6 to 7 m wide. This dimension is chosen so as to allow maneuvrability of appropriate mine machinery and equipment, to meet production requirements and to ensure roof stability. Over the last two decades, a great deal of research effort has been expended to understand the behaviour of roadways in different strata within this width range. The results have improved the understanding of the strata behaviour to such an extent that 6 m wide roadways are developed with a high degree of confidence. With the advancement of technology and the quest to mine at a lower cost, some mines in South Africa have started considering the benefits of other types of mine machinery that will require much wider roadways to ensure optimum productivity. The roadways required will have to be about 10 - 14 m wide. The challenge confronting these coal mining companies is the potential instability that might be associated with such wide roadways. This dilemma is aggravated by the fact that, apart from theory, nothing is known about the expected behaviour of such wide roadways. This led to experimentation at a selected site in a South African coal mine where 10 m and 14 m wide roadways were developed and monitored. This paper highlights the experimental procedure adopted, discusses the results obtained, compares the prediction of elastic theory to reality and set the precedence towards understanding the behaviour of wider roadways in South Africa.

Jan 1, 2001

By Nengxiong Xu

The WTZ coal mine is located adjacent to an auxiliary dam in P. R. China. The mining-induced ground movements are calculated using a 3-D numerical procedure based on the finite difference method (FDM) to judge whether the extraction of the coal seam will have a negative impact on the dam. First, the values of the rock mass mechanical parameters in the numerical model are estimated using the available literature that relates intact rock and discontinuity properties to rock mass parameters. Then, based on available surface subsidence monitoring data for an area in WTZ mine, the main mechanical parameters of coal and rock masses are calibrated by a back analysis procedure that combines an experimental design technique with numerical simulations. Then the reliability of these rock mass parameters is verified. Finally, according to the planned mining sequence, predictions of mining induced surface subsidence are computed in steps, and the boundary of the ground movement area of each step is determined. The nearest distance from the boundary of the surface movement area to the edge of the dam foundation was found to be about 1347 m. The maximum surface subsidence within the mining area turned out to be 2.7 m, and the maximum settlement point was found to be close to west-south corner of A2 mined area. These findings led to the conclusion that the coal seam mining would not cause dam damage.

Jan 1, 2013

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By Guorui Feng, Min Zhang, Yi Luo, Jian Yang, Yujiang Zhang, Junwen Bai

"Safe mining of coal seam sandwiched between abandoned upper and lower room-and-pillared mines (ULPM) ·is increasingly becoming the focus of attention in recent years, which is closely related to the damage intensity of the upper and lower interburdens. The #7 seam with ULPM in Baijiazhuang coal mine was selected for this research. According to the mining and geological conditions, the vertical stress and plastic zone distributions were determined first by numerical simulation. Then, a theoretical model based on the elasti-plasticity theory was developed. The stress distribution and failure zone created in the interburden by mining the upper and lower seams were determined. Finally the feasibility of mining #7 seam between the abandoned upper and a lower seam was evaluated. The results show that: (1) the distributions of abutment pressure and plastic zone coincide, both of which can be used to evaluate the failure zone in ULPM. The failure zone penetrates the whole upper interburden, while only parts of the lower interburden fail. (2) the theoretical failure zone coincides with the maximum distribution zone of abutment pressure and plastic zone obtained by numerical simulation: the failure zone height in the lower interburden is less than its thickness, while that in the upper interburden is larger than its thickness. (3) the #7 seam is located in the failure zone created by the upper seam room-and-pillar mining, which leads to well-development fractures and blocky fragments in the roof, thereby it is unstabled. (4) when mining the #7 seam in the interburden, the key is to control the roof strata and proper support measures should be taken timely to ensure safe mining.INTRODUCTIONMany coal mines in China mine the thick, superior and easily mineable resources preferentially, while the thin, inferior and difficult-to-mine resources were abandoned (Chappells and Trentrnann, 2015; Zhenfu, 2012; Xu, et al., 2015; Guorui, 2009). As the results of deficient geological data and shortage of investment capital, the residual coal resources distributes in many mining areas in China.In recent years, many residual coal seams sandwiched between the abandoned upper and lower room-and-pillar mines (ULPM) were explored in Shanxi Province, especially in the mining area of Datang, Xishan and Luan (Figure.1). The reserves of residual coal seams in ULPM are considerable, increasingly becomes the focus of attention among scholars and engineers."

Jan 1, 2016