Search Documents

By G. P. Dvoichenkova, E. A. Trofimova, M. V. Zaskevich, V. A. Chanturiya

The paper presents theoretical and practical aspects of directed adjustment of physicochemical properties (pH,Eh) and ion composition of recycle and mine water by electrochemical treatment. Treatment is run in the conditioners of diaphragm-type with production of alkaline catholyte of pH value up to 12 and acidic anolyte of pH up to 2. In process of water electrolysis the directed motion of Mg2+ and Ca2+ ions is observed from anode volume to cathode one, were they precipitate as hydroxides and carbonates; it leads to decrease of salt content in anolyte and catholyte. The anolyte has been concentrating anions, it is being saturated with oxygen, which reaches 20-35 mg/L. The results of experimental and industrial testing of electrochemical technique for mine and recycle water in flotation of diamond-containing and sulphide-scheelite, hematite, phosporite, apatite-nephelite, bauxite ores indicated the increase of recovery up to 2-1 5% and grade up to 0,5-2%, concurrent with decrease of reagent consumption from 15 to 50 %. Modules of industrial conditioners of different type capacity have been developed.

Jan 1, 1995

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995

By B. Howerton, M. M. Matlock, D. A. Atwood

In the Gold-Cyanide Process (GCP) the cyanide anions act to solubilize the gold and silver present in the ore, and mercury as well. The resulting mercury and cyanide rich effluent are serious health and environmental problems. Currently, there is no mercury treatment from the ore leach solution since there are no precipitating agents or other technologies which can be used effectively in the pH ~ 10solutions. Recently, however, we have developed a new chelate ligand that is impervious to this level of pH and it can be used to precipitate Hg from NaCN solutions. On an actual sample taken from an active gold mine the chelate selectively reduced the mercury level from 34.5 ppm to 0.008 ppm within 15 minutes. Importantly, the gold and silver levels remained unchanged throughout this process. Thus, the environmental impact of Hg released in the GCP can be drastically reduced. Moreover, with a mercury treatment technology now available it may be possible to change, or reinvent, the entire GCP process.

Jan 1, 2003

By T. Tempel

In 1994 Newmont Gold Company commissioned a 2.5 Mt/a refractory gold ore roasting plant near Carlin Nevada. Many unique characteristics of this facility required use of specialized materials of construction in the areas of dry grinding, roasting, gas cleaning, and sulfuric acid production. Process conditions and design criteria that necessitated the use of special materials include; siliceous and abrasive ore, low roasting temperatures, gas streams with high concentrations of oxygen and sulfur, and stringent environmental regulations. Materials selected for use were ceramics, corrosion resistant steels, high temperature steels, and high temperature polymers, lead, polypropylene and low flammability PVC.

Jan 1, 1997

By Ted H. Eyde

Specialty sand and bentonite are produced in the plateau province from the Bidahochi Formation near Sanders, Apache County, Arizona. It appears that deposits of both sand and bentonite formed during the Pliocene in fluvial and lacustrine environments, respectively, along the west side of the Defiance Uplift. The bentonite is an alteration product of airborne vitric ash that fell or was washed into lakes. In the Cheto district, the individual bentonite horizons, which range from less than a foot to more than 10 feet thick, are restricted to the position of the medial volcanic member. Bentonite production began at the Allentown mine in 1924 and the Chambers mine in 1926. In 1933 strip mining of the extensive deposits in the Cheto district commenced. Production increased each year to a peak of 270,000 tons in 1957. As a result of the introduction of synthetic zeolites into petroleum refining, production declined. About 40,000 tons of bentonite are currently produced from the district each year. Bentonite is shipped out of State for processing into desiccants, thickeners, and acid-activated clay products. The specialty sand was derived from Permian sandstones and deposited by streams draining the Defiance Uplift. Although stream channels are usually restricted to the upper member of the Bidahochi, stratigraphically above the bentonite horizon, a few actually cut through the bentonite. The well-sorted sand, suitable for use as a proppant in hydraulically fractured oil and gas wells, is localized in elongate lenses along the margins of the channels. These lenses range from 5 to 50 feet in thickness and often extend thousands of feet in both width and length. The sand is about 97 percent silica, has a yield of 40 percent in the minus 20 plus 40 mesh size fraction, and has a roundness of 0.6 to 0.7 on the Krumbein scale. Production of this sand began about 1961. All of the current production, which amounts to about 40,000 tons per year, is sold in the petroleum-producing area near Farmington, New Mexico.

Jan 1, 1987

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump's height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump's radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By Harold Potter

(1) A great deal of experimentation has been carried out by the Wet Process Cement Manufacturers in connection with additives which make possible the production of a pumpable slurry at reduced moisture contents. We ourselves have made dozens of tests both at Laramie, Wyoming and Monolith, California. (2) The viscosity or pumpability of a slurry at a definite moisture content and fineness seems to depend on two basic phenomena. One is the physical structure of the raw material itself, which on fine grinding may or may not be excessively hydrophilic (water adsorptive). Usually crystaline or glassy raw materials are non- hydrophilic. The fine grained amorphous raw materials such as shales and clayey limestones very frequently are, however. (3) The second basic phenomenon affecting the hydrophilic tendencies of the raw material is the presence of certain soluble salts, especially gypsum and small amounts of alkalin carbonates or oxides. (4) Various soaps, and phosphates can be used to produce a pumpable slurry of low moisture content when using hydrophilic raw materials as well as can other proprietary materials such as certain long chain carbon compounds. Too frequently however, the price of such additives in conjunction with the amount required prohibits their use in the cement industry.

Jan 1, 1959

By Justin Kolster, Donald Benjamin, Kyle White

Expansion of the Plum Island Wastewater Treatment Plant requires interconnection of three operating pump stations using only two existing 10-ft diameter shafts for access. These two existing shafts require additional support to allow access 130 feet below grade. Interconnection requires rehabilitation of an existing tunnel, excavation of two new tunnels, and abandonment of additional existing tunnels. Construction has discovered unexpected conditions at all three connection points. The CMAR contracting method has effectively accommodated project team discussion, value engineering decisions, and allocation of risk during preconstruction and construction phase services.

Dec 1, 2022

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

Nickel demand is increasing along with the rising need for stainless steel and other alloy steel/iron. The small addition of nickel in such materials can improve impact strength, ductility and corrosion resistance. Nickel is generally obtained from nickel sulfide ores (nickel associated with sulfur) and nickel laterite ores (nickel associated with iron and magnesium silicate). Almost 60 percent of nickel is now produced from sulfide ores, despite its existence in sulfide ores being less than in laterite ores. However, the depletion of sulfide ore reserves makes the mastery of nickel laterite ore processing of important and immediate concern. Selective reduction followed by magnetic separation has been in development in lateritic nickel ore processing to overcome the issues of high energy consumption and pollution associated with conventional pyrometallurgy methods such as blast furnace and rotary kiln electric arc furnace (RKEF).

By LeEtta M. Shaffner, John R. Marks

INTRODUCTION In the last twelve years, underground stoping methods at the Homestake Gold Mine have evolved from open cut-and-fill with jacklegs, cribbed raises and electric slushers to ramp-based mechanized cut-and-fill (MCF) and vertical crater retreat (VCR) with dieselpowered loaders, trucks and drill jumbos. The evolution was swift. Unfortunately, ventilation practices have had trouble keeping pace. Stope ventilation is still too dependent on auxiliary fans and coolers. A single large MCF stope might contain up to eight headings, each of which requires significant ventilation resources when a diesel loader is present. Air is shortcircuited all too frequently through mined-out VCR panels. These factors and the recent rapid decent of the center of mining prompted a study to improve ventilation practices and to more accurately project future requirements. BACKGROUND In 1992, the underground portion of the Homestake Gold Mine produced 8336 kg of gold from 1407 ktons of ore (268,000 oz from 1,551,000 st). The ore is hosted in low to medium grade meta-sediments. Stoping took place from 420 to 2347 m below the surface (1400 to 7700-ft levels). The weighted center of mining was 1662 m deep (5450-ft level) in 1990 and is projected to be 1890 m (6200-ft) in 1993. The deepest level is 2440 m (8000-ft) where the virgin rock temperature (VRT) is 56.1°C (133F). The mine is ventilated by 504 m3/s (1,069,000 cfm) measured at mid-exhaust-circuit density. The air-conditioning system includes an 8.1 MWR (2300 ton) controlled recirculation plant, a 2.0 MWR (580 ton) chilled water plant, a 1.0 MWR (290 ton) exploration drift refrigeration plant, 28 spot-coolers totaling 3.4 MWR (960 tons) and 35 spray coolers totaling 1.5 MWR (420 tons). The mine employs 117 diesel units with a total nameplate rating of 7961 kW (10,672 hp). These units include twenty-four 1.5m3 (2-yd) loaders, twenty-six 2.7m3 (3.5-yd) loaders, fourteen 3.8m3 (5-yd) and two 7.6m3 (10-yd) trucks, and assorted utility vehicles and drill jumbos. THE STUDY In April 1991, the University of Nevada-Reno (Mackay School of Mines) and the South Dakota School of Mines and Technology cooperated with Homestake on an MCF study. Mackay instrumented a stope with thermocouples, air velocity meters and hygrometers (Duckworth, 1992). South Dakota Tech conducted a finite-elements computer analysis of a back-filled MCF stope with/without light-weight shotcrete insulation on the sidewalls and back (Chellam, 1992). Homestake conducted an empirical analysis of deep-level MCF stoping. This paper describes the Homestake study. Twenty-three of the forty MCF stopes deeper than 1800 m were surveyed at least once during the last quarter of 1992. The stopes not included were being cable-bolted or back-filled. Figure 1 shows the complexity of one of the ramp-based stoping areas included in the survey. This particular stope has six separate production headings. A baseline wallrock heat load was derived for each stope or heading from psychrometric calculations. Broken ore, waste rock fill and fissure water were noted when present and the effects included in the baseline heat load. Other heat sources often mentioned in the literature such as metabolic heat from workers, heat from explosives and small electric loads were neglected. Fan heat was considered part of the ramp & crosscut heat load and thus not included in the study. Diesel heat was addressed separately. RESULTS Survey results, plotted as the heat flux against VRT, are shown in Figure 2. The equation for the regression line is: W/m2 = 2.1236*VRT - 75.405 The 0.31 correlation coefficient is poor which implies that the results should be used cautiously. Previous experience strongly suggests that differences in productivity are most likely responsible for the scatter in data points. A rapidly advancing stope will have a

Jan 1, 1993

By Hans G. Kok

At this time in the history of engineering and construction, cost indexes give weekly evidence of the sharply rising costs of labor and materials. Paralleling the rise in construction costs are the costs of plant maintenance. Automation of the modern industrial plant has permitted a substantial reduction in the total number of employees required for plant operation. Of this reduced total, however, up to one-half of the employees may be engaged in plant maintenance. Management's decision to risk investment capital for a pro- posed plant or improvement is increasingly dependent upon the engineer's ingenuity in designing plant systems and structures which will require a minimum of materials and labor for manufacture, installation, and operation and which will be maintenance-free to a maximum degree. This paper concerns itself with the structural elements of bulk material handling systems in which the foregoing factors influenced the design to a considerable extent.

Jan 1, 1969

By Rick Frechette, Greg Nelson

"The 2018 Elko Roundtable was held at the Red Lion in Elko, NV on March 15, 2018. The gracious host was once again Knight Piésold. Attendance was robust with representatives from more than 14 mining properties across Nevada representing nine corporations. Total attendance was at its highest in almost a decade. A high level of interest was also gauged by the number of companies with multiple attendees.The topic of water in mining was clearly a factor in creating the large show of interest. In terms of industry trends that are tracked annually, this topic had been absent from the list for more than 10 years (Deloitte, 2018) but was squarely planted there this year. And deservedly so. Three attending companies are signatories of the International Council on Mining and Metals (ICMM) which espouses a firm stance on water stewardship (ICMM, 2017).How’s the water?It is reported that water scarcity affects more than 40 percent of the world’s population (Deloitte, 2018). Consumption of water in the United States, based on the last detailed census, entails only 1.5 percent usage by the mining industry. The largest users are reportedly thermoelectric power and irrigation, combining for more than 75 percent of the U.S. consumption. During the prior census period, water usage at mines was up dramatically (USGS, 2014).Mine water source usage is primarily a mix of ground water and saline or fresh surface water resources. Over the previous period, saline sources experienced the greatest percentage in growth as a mine water source, nearly doubling in use. Nevada ranks second as a state nationally in mine water consumption. California is the leader, and Nevada is immediately followed by Utah and Alaska (USGS, 2014).Water rights in Nevada and the ongoing litigation at the state level, particularly over the Humboldt River basin, have elevated the concern over the supply of water and have raised the interest regarding the topic of water across the mining industry as well as within other industries.The Elko Roundtable meeting began with a safety share and introductions, and included each attendee mentioned a water problem or solution that he or she would like to discuss during the day. An interesting list of subtopics was developed from this round robin and yielded the following most common themes:• Mine pit dewatering during operation and pit wall stability.• Draindown from tailings dams and heap leach pads and dealing with this at closure.• Post closure pit lakes, pit lake water quality and associated water rights."

Dec 1, 2018

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the U.S. mining workforce who are potentially exposed to RCS [1,2] as various ore bodies are drilled, blasted, hauled by truck, crushed, screened/sized and transported to their destinations. To examine a method for assessing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on 80 miners across seven unique mining sites. The data were then collated and partitioned using a thresholding scheme to determine exposures that were in excess of 10 times the mean exposure for that worker. Focusing on these short-duration, high-magnitude exposures can provide insight into implementing controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20 percent or more by reducing exposures that occur during just 10 minutes of work per eight-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By Duk-Won Park

A new gage for monitoring fractures in underground openings was successfully developed utilizing the reflection photo-elastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so that remedial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by the use of rubber backing. Crack growth as little as 0.003 inch up to as much as 0.1 inch width were detected in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in the laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1982

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

Coalbed methane development is an important way to effectively realize a source of clean energy and reduce emissions of carbon dioxide and other gases. However, due to the low permeability of coal seams, the development of coalbed methane in China has encountered substantial barriers. Protective layer mining can efficiently minimize in situ stress and increase coal seam permeability, thus improving gas drainage and avoiding gas disasters. This study analyzed the characteristics of gas migration and the change in permeability during the in situ stress releasing process through experiments and numerical simulation to study the gas drainage effect of a coal mine in an unloaded coal seam under specific geological conditions. First, a stress–strain-seepage coupled test of coal was carried out, and the evolution features of coal permeability during stress loading and unloading processes were investigated. Second, experimental results were used to develop a mathematical model of coal seepage under mining unloading conditions. Finally, a numerical model was developed based on the real geological conditions of the Wulan coal mine to explore the characteristics of in situ stress release and permeability evolution, as well as the gas drainage process in an unloaded coal seam. By combining protective layer mining and gas drainage technology, the risk of gas outburst is significantly reduced.

Oct 1, 2022

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By Donald L. Gaughenbaugh

Under the terms of the 1970 amendments to the Clean Air Act, the EPA established national ambient air quality standards for a number of pollutants. Sulfur dioxide (SO2) was one of these pollutants. These ambient air quality standards have had perhaps their biggest impact on the power utilities. In an effort to meet the air quality standards set forth by the EPA, utilities using high sulfur fuels have been forced to install flue gas desulfurization (FGD) systems. The majority of FGD systems in operation today are nonregenerable systems, that is the by-product of the system is disposed of, usually into settling ponds. Limestone slurry is the most common reagent used to remove SO from the flue gases. The calcium carbonate (limestone) slurry interacts with the flue gas, absorbing the SO2 and forming a by-product of calcium sulfate/sulfite which is disposed of.

Jan 1, 1986

By Steven J. Van Kauwenbergh, Talaat A. B. Lawendy

Batch laboratory-scale beneficiation tests were conducted on four high-iron phosphate samples. These samples included sedimentary ores (Tilemsi Valley, Mali and Tahoua, Niger), a sample from an igneous phosphate deposit (Matongo, Burundi), and a fine-grained phosphatic iron ore processing residue from Chile. The Matongo phosphate deposit occurs as a thick (up to 80 m) residual blanket of P205-enriched soil over solid parent rock (carbonatite and associated rock types). Although the Matongo deposit is an igneous deposit, ore from the deposit can be subjected to beneficiation treatments commonly used to treat sedimentary rocks. The beneficiation flowsheets designed to process these diverse ore types involve attrition scrubbing, size classification, and flotation. At the best flotation conditions tested, phosphate concentrates assaying 32.0%-39.0% P205 and 1.0%-1.5% Fe2O3, were obtained at 64.2%-82.2% overall P2O5 recoveries from run-of-mine (ROM) ores containing 9.2%-28.6% P205 and 5.9%-16.1% F,20,. A cleaner phosphate concentrate assaying 33.1% P205, 1.8% A1203, and 3.3% Fe2O3 at 53.4% overall P205 recovery was obtained from the phosphatic iron ore residue that originally contained 4.5% P205, 8.0% A1203, and 17.6% Fe2O3.

Jan 1, 1993

By Paul Basinski

The Northern Reese River Valley is in west-central Lander County approximately 31 miles north of Austin, Nevada in the north-central Basin and Range Province (Figure 1). Authigenic zeolites, which were previously undescribed in the literature, are voluminous in this small sedimentary basin. Uranium mineralization is also abundant in this study area. Until now, what we believe to be cause and effect have not been put together. X-ray diffraction, differential thermal analysis, and scanning electron microscopy reveal clinoptilolite, erionite, analcime, and minor chabazite to be present (Figures 2, 3). Assays show uranium to be present in thicknesses up to 0.7 meters at amounts up to 0.10% eU308. The sediments in the Northern Reese River Valley belong to the Mio-Pliocene Humboldt Formation equivalents. This formation consists largely of tuffacious lacustrine and fluviatile sedimentary rocks. Mudstone is the dominant lithology and intercalated thin zeolite strata (usually less than 0.6 meter thick) are present. Zeolites in the Northern Reese River Valley were diagenetically derived from rhyolitic glass deposited in a shallow, saline-alkaline lake under arid to semi-arid conditions. Clinoptilolite from the study area was K-Ar dated at approximately 4.7 + 0.5 million years which corresponds to Middle Pliocene age (Krueger and Basinski, in press). This age is further substantiated by Middle Pliocene mammalian fauna collected in the vicinity by Deffeyes (1).

Jan 1, 1979