Search Documents

By Fulvio V. Fonseca

The Trombetas bauxite deposits were discovered by ALLAN, as from the original work of the geologists Drs. E. E. GREIG and 3.A. STAARGAARD on the axis of the Amazon river, between Manaus and Santarem - (see fig. 1). With research licences obtained in 1965 by the SANTA RITA BAUXITA - a subsidiary of ALAN a group of Brazilian geologists, under the supervision of IGOR MOUSASTICOUSHVILLY, begins researches on the areas of Parintins, Juruti and Mathias with unsatisfactory results. In 1966, photographs obtained from the US Air Force and the Brazilian Oil Company PETROBRAS -, covering an Amazon region between Parintins, Santarem and north of Trombetas river, permitted the identification of a great number of plateaux between the Nhamunda and the Trombetas rivers. Based on this information, a research group has worked intensively from 1966 to 1967 allowing the discovery of the trihydrated bauxite in a quite large area. After five years of intense work and analysis of approximately 56.000 samples, near 500 million of tonnes of bauxite are evaluated on the several plateaux of the, area, thus insuring the commercial exploration of these deposits. Such discovery places Brazil among the detainers of the main bauxite stocks of the world and as a potential exporter.

Jan 1, 1980

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

By Nicola Beltrandi, Andrea Pigorini, Holad Mohamed Dahir, Ezio Pedone

"Genoa is a very distinctive city located between mountains and the sea and infrastructural upgrading works often have to deal with the intersection of existing infrastructures. This is the case for the new railway tunnel construction between the stations of Brignole and Principe which under-cross two existing double-track tunnels in operation. The latter have been constructed with masonry bricks and the vertical distance between old and new tunnels is approximately 1m. Due to rock characteristics and the urban environment, stability and vibrations control are the main issues. Consolidation work with the fore-poling method and a specific sequence of excavation, primary lining and final lining support have been designed to assure stability and settlement control. A hard rock road-header has been used to assure vibration control. Finally, a real time monitoring has been implemented. The article presents monitoring and back-analysis results of the under-crossing of the existing tunnels. GENERAL LAYOUT OF WORKS The Genoa railway junction constitutes an integral part of the Ventimiglia-Genoa-Novara-Milan railway line route and it is included amongst the railway systems of the Tyrrhenian-Northern European multi-modal corridor (corridor of the two seas or corridor VII Genoa-Rotterdam). The main aims of the project concern the upgrading of the existing lines and the separation of the long-distance passenger and freight traffic flows from those of a regional and metropolitan type. The project includes: •,Completion of the connection with the port of Genoa Voltri and the Italy-France coastal route. •,Interconnection with the future Terzo Valico dei Giovi mountain pass route towards Milan. •,Upgrading of the Genoa Voltri – Genoa Brignole main line to four/six tracks. Rearrangement of the systems at the Genoa Voltri, Genoa Sampierdarena and Genoa Brignole Stations, reorganisation of the services in the Genoa Terralba area and interchangeability with the metropolitan system complete the design activities. The contract which includes civil and technology works is divided into four construction lots (ref. Figure 1):"

Jan 1, 2016

By Olav Moklebust

The R-N Process is an outgrowth of the development by the National Lead Company's Norwegian subsidiary Titania A/S, of a process for producing metallic iron and a high titanium content co-product from ilmenite. Development of the process for the treatment of iron ores was continued as a joint project of the Republic Steel Corporation and the National Lead Company in 1953. More recently in July, 1957, the R-N Corporation was created by these two companies to undertake the commercial promotion of the results of this joint project. This paper has been prepared with the permission and encouragement of these three companies. The R-N process has as its objective the making of metallic iron from iron ores or iron ore concentrates. The general principles of the process have already been disclosed in technical papers and patents. In general the process comprises the following steps: 1. Iron oxide in crushed natural iron ores or iron ore concentrates is reduced to about 95% metallic iron, without fusion in a rotary kiln in the presence of solid carbonaceous fuel,*such as, coke or char, limestone and combustible gases. 2. The kiln discharge, consisting of metallized ore, coke, lime and coke ashes, is cooled. The excess coke is regenerated and recycled to the kiln feed.

Jan 1, 1959

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By C. D. Keith

Erie Mining Company, a pioneer in the iron ore pelletizing industry, has continued to develop methods and equipment to improve cost and quality. Under the management of Pickands Mather & Co., this property, owned by Bethlehem Steel Corporation, Youngstown Sheet and Tube Company, Steel Company of Canada, Ltd., and Interlake, Inc., has initiated a number of operating improvements for the taconite industry. One of the most noteworthy of these, which is applicable to the entire mineral industry, is the principle of fine screening with rappers (FSR). Erie's original efforts in the field of fine screening, which date back to 1961, were described in the April 1967 issue of the MINING ENGINEERING magazine. In that same month, Erie placed into operation a full scale PSR and regrind plant addition, capable of processing 10.3 million long tons of iron ore concentrates, produced by conventional taconite grinding, classification, and magnetic separation methods. Since this first successful commercial operation of the PSR principle et Erie, it has been applied in eight other iron ore beneficiation plants end is being tested by other U.S. and foreign companies. In addition to the use of PSR units at Erie Mining Company, Pickands Mather has applied PSR to other of its managed properties end to projects under development. This paper covers these applications as well as a now application at Erie Mining Company.

Jan 1, 1971

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010

By M. Kane, O&apos

BHP Iron Ore initiated research programs in January of 1995 to develop long term plans for decommissioning of the waste rock material at their Mt. Whaleback operation. More than 2 billion tonnes of waste rock were deposited during the past 30 years. Ultimately, the operators will deposit a total of approximately 5 billion tonnes in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semi-arid climate adjacent to Newman, Western Australia, approximately 1200km north-northeast of Perth, Western Australia. The primary research program includes the development of technology for the long term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion, and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. A laboratory program and the soil-atmosphere modelling completed to design the horizontal field test plots are described. The construction of the horizontal surface field test plots are discussed together with the field instruments installed to monitor performance. The key components of the instrumentation program are the design and installation of large scale field lysimeters to measure the unsaturated flow of moisture into the waste rock from the base of the cover layer. The cover system is designed to maximize infiltration during wet periods for subsequent evapo-transpiration while minimizing surface runoff. The result is a near zero net infiltration to the underlying waste material. A key feature of the design is the use of pit run waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long term performance.

Jan 1, 1998

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By Ramkrishna Agarwal

A low grade iron ore is mined underground at Grace Mine using the panel caving method. Most of the development work is located in footwall. The runways for LHD equipments are heavily supported with steel sets on five foot centers. The sets are embedded in two to three feet of concrete. The initial cost of support is one of the largest single costs of production. During the process of ore-win¬ning, supports frequently fail, necessitating expensive repair. There is no systematic pattern to the failure of supports. A rock mechanics program was launched to isolate causes and their relative contributions to the failure of supports. The preliminary results are presented. A typical portion of a runway is instrumented to monitor rock mass movements around the runway and the corresponding response of supports as various mining activities are carried out in the neighborhood. We believe that such a program is a prerequisite to any remedial measure to alleviate pressure problem at Grace Mine.

Jan 1, 1973

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By Remo Grandori, Fabrizio Antonini, Giorgio Dolcini

The paper describes the anticipated and the encountered geology, the TBM selection concepts and the machine special features, the tunnel sections, the achieved advance rates and the geological problems, the machine behaviour and the main setbacks caused by ground conditions the Authors also discuss the scopes for possible improvements to double telescopic shield machines, with special reference to their application under extreme geological conditions such as those that were met in the course of Los Rosales Tunnel excavation.

Jan 1, 1991

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001