Search Documents

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By John Rajala

The Otjikoto Gold Mine in the Republic of Namibia is located approximately 300 kilometers north of the capital city of Windhoek. The project features surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and recovery of gold. Initial mill design capacity was 2.5 million tonne per annum but then expanded after 9 months of operation to 3.1 million tonne per annum. The technical steps to establish the Otjikoto mill design from process selection in the due diligence stage, through flowsheet development in the feasibility study followed by detailed engineering design are reviewed in this paper along with mill performance during start-up and in 2019.

Oct 30, 2020

By A. J. Teske

Sustainable Development is a very broad initiative in the mining industry, with major components running over the entire life of the mine. It likely commences with pre-exploration permitting and continues to post-mining final closure and possible land reuse. Most major mining corporations embrace the sustainability initiative, either out of a sense of social responsibility or out of necessity in order to continue doing business. But many may view the overall initiative as an added ?cost of doing business.? In many elements of sustainability, there clearly can be added cost ? some as simple as complying with self-imposed sustainability reporting. Fortunately, one major element of sustainable development can clearly be shown to reduce costs ? energy resource management. This paper will describe how the mining industry sustainable development effort differs from other industries, but can benefit from their experience in energy resource management. The mining industry can utilize proven methods from other industries to further their energy management efforts. In addition, many of the resources developed and employed to promote better energy resource management in non-mining industrial settings will be listed.

Jan 1, 2010

By A. Singh

"Considering the dominant role of fertilizers in global phosphate production, it is evident that with the ever increasing development in agriculture there will be a growing demand for phosphate beneficiation. With the rapid depletion of high quality reserves, investigations into more complex and lower grade ore bodies are required. The Minerals Processing Division at Mintek has been involved in process development and flowsheet design projects on phosphate resources since 2003. This paper will discuss the processes that Mintek has explored and employed to upgrade various phosphate ore bodies (>30% Phosphorous Pentoxide (P2O5)) in preparation for end user application. These are aimed at an improved understanding of ores in terms of their varying mineralogy and the development of appropriate process routes to meet product specification. OVERVIEW OF MINTEK Mintek is a state owned science council that undertakes R&D, consulting and sells products and services into the minerals beneficiation industry. Mintek has been in existence for 83 years with a current permanent staff complement of 750 of which 300 are professionals with a tertiary education. Being a non-profit organisation, the majority of funding comes from state grant and earmarked funding. All research is needs-driven exploring innovation through technology and process optimisation trends. Owing to a solid base of expertise, extensive laboratory and pilot facilities, and a historical database of knowledge, Mintek is well positioned and equipped to execute projects on a scoping, feasibility, prefeasibility and bankable level. USES OF PHOSPHATE Phosphate is the component in fertilizer essential for root and stem development in plants as well as rejuvenation of harshly depleted soil for which there is no agricultural substitute. Phosphate rock is essential for global food security with 87% used in the production of fertilizers. In agriculture as fertilizer, phosphate is one of the three primary plant nutrients in addition to nitrogen and potassium. In former times, it was simply crushed and used as is, but the crude form is now only used in organic farming. Normally it is chemically treated to make Single superphosphate (SSP), Triple superphosphate (TSP), or Mono-ammonium phosphates (MAP) and Di-ammonium phosphates (DAP), which has a higher concentration of phosphate and is more soluble, thus more suitable for plant absorption."

Jan 1, 2018

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof (XP) enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4) air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway (TR). Researchers at the National Institute for Occupational Safety and Health (NIOSH) measured TR pressures of lithiumiron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 294 bar (4260 psia) of pressure during a TR, far exceeding minimum pressure containment specifications for conventional XP enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce TR pressures to levels below that expected for CH4-air ignitions. Measured TR temperatures were below the minimum autoignition temperature of CH4-air.

Nov 6, 2020

By Yanan Zhang, Hongwei Deng, Feng Gao, Bo Ke

Recently, liquid carbon dioxide (L-CO2) blasting technology has attracted attention due to its good fracturing effect and safety performance, especially in coal seam permeability improvement. This paper analyzes the blasting effect of L-CO2 based on experiments and studies the fracturing mechanism from the perspective of stress wave action via theoretical analysis and peridynamic simulations. The results indicate that L-CO2 blasting achieves a good fracturing effect without forming a crush zone, and the loading rate and strength of the stress wave are key factors.

Jan 19, 2022

By A. A. Terchick

It has been reported in the literature that there is a substantial economic incentive for removing sulfur from coal. Therefore, U. s. Steel initiated an investigation to determine the feasibility of lowering the sulfur content of its Pittsburgh-seam coal. Preliminary crushing and washability studies on a representa-tive sample indicated that substantial sulfur reductions could be attained. Figure 1 shows the effect of the top size of a given coal sample on the sulfur content of the float-l.45 specific-gravity fraction of coal. At a top size of 3 inches, the raw-coal sulfur content of 2.32 percent was reduced to 1.64 percent. Crushing to a top size of 20 mesh reduced the raw-coal sulfur to 1.25 percent. Below a top size of one inch, the sulfur content decreased rapidly as top size was decreased. Figure 2 shows the effect of specific gravity of separation on pyritic sulfur. Normally this coal has an organic-sulfur content of approximately 1 percent. As expected, pyritic sulfur was reduced as the separating gravity was lowered for all the various size fractions shown. The rate of decrease in pyritic sulfur was gradual above 1.45 specific gravity, but great below 1.45. Greater sulfur reductions were attained on the coarser sizes with decreasing

Jan 1, 1971

By W. G. Pariseau

A study of coal pillar strength at the Beehive Mine in central Utah was done in the 1970s. This study was a cooperative effort by the University of Utah, RE/SPEC, Inc., and the American Coal Company and was funded by the U.S. Bureau of Mines. Mine measurements of closure at 117 points and pillar stress using 119 vibrating wire stress gauges were made during retreat mining in this room-and-pillar operation. Laboratory testing for the strength and modulus of 372 coal cylinders up 0.3 m (1 ft) in diameter and 0.6 m (2 ft) in length was also done. Two-dimensional finite element model analyses complemented the study. However, the real world of mining is three-dimensional and in consideration of the significant advances in computing power since the time of the original study, a revisit of the data seemed warranted. In this regard, a novel finite element method was used that allows for the whole-mine analysis of tabular excavations on the kilometer scale and yet enables details to be obtained at pillar walls on the meter scale. The effects of material properties variability in situ and of joints can also be taken into account. Results that compare computed two- and three-dimensional seam-level closures with mine measurements show noticeable differences; three-dimensional results are reasonable, while two-dimensional results overestimate closure by nearly a factor of two.

Jan 1, 2014

Newmont has been producing gold from the Carlin Trend for over 45 years. Naturally the focus, scale and complexity of the operations have changed considerably over this time. Newmont discovered and developed the Carlin Main ore body which is located about 32 km (20 miles) north of Carlin Nevada. The property was developed as a one mine one gold mill treatment plant operation which produced about 6,200 kg (200,000 Troy ounces) of dorè gold bars per year. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a dorè bar for sale.

Jan 1, 2012

By S. R. Dismukes

Mining is likely to be targeted by The United States Environmental Protection Agency (“EPA”) as one of its key enforcement targets for fiscal year 2002-2003. Identifying the mining industry as an enforcement target, coupled with an increase in enforcement activity in recent years, places each mining operation at increased risk of receiving enforcement attention. A properly developed and implemented Environmental Management System (“EMS”) tailored for your operation is invaluable in reducing the risk of incurring liability for non-compliance. At the heart of an effective EMS is an audit program that checks the company’s compliance with environmental requirements. In addition, audit privilege (in select states), voluntary self-disclosure, and the attorney-client privilege serve as very effective tools for managing those liabilities that may arise during auditing a well-developed program. Of course, these latter tools are effective only if the auditing program is properly structured and properly managed. EPA and some states also provide varying degrees of immunity for environmental violations that are voluntarily disclosed in writing by the company. However, self-disclosure laws and policies typically prescribe stringent requirements for parties seeking to take advantage of them. For example: U.S. EPA has recently extended the time period in which to provide full written self-disclosure to 21 days. However, U.S. EPA’s revised Self-Disclosure guidance also addresses when a company obtains knowledge of a violation for purposes of triggering the 21-day clock and specifically extends the knowledge requirement to include the company’s agents and consultants. This expansion increases the difficulty companies may have in clearly defining and managing when they obtained knowledge. This difficulty increases the importance of managing factual development and the strategic use of other

Jan 1, 2001

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By Wei Victor Liu, Omer Faruk Ugurlu, Chengkai Fan, Bei Jiang

Accurate prediction of truck productivity plays a pivotal role in improving the efficiency and profitability of openpit mining operations. This paper proposes a deep neural network (DNN) model to overcome the challenge of predicting truck productivity in openpit mines. The prediction model was built using eight variables and was optimized by considering different train-test split ratios, numbers of hidden layers and neurons, and activation functions. The proposed model’s performance was evaluated using various metrics and compared with other commonly used machine learning algorithms. The results showed that the proposed model outperformed traditional machine learning models by achieving higher prediction accuracy. Moreover, a single-variable sensitivity analysis showed that haul distance is the most influential variable for predicting truck productivity. This study marks a pioneering effort in employing DNN to predict truck productivity in openpit mining, signifying a notable advancement in the field.

Jul 1, 2024

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015

By Ehsan Nasiri, Keivan Pak Iman

Historically, boulders are a frequent source of problem in soft ground tunneling. It is important to attempt to make an assessment of the nature and quantity of the boulders, although in many cases, it will be impossible to do so with great accuracy. Boulders, can pose major problems for TBMs in terms of slowing down or halting the tunnel advance, cutter damage, and abrasive wear. Although proper selection of the TBM and the cutterhead can reduce the risks, ground uncertainties still cannot be eliminated. The paper reviews a case study of a 3480 mm diameter EPB-TBM in Toronto utilized for completion of 2.5 km tunnel in Glacial Till, crossing the CP railway, HWY 401, a creek, and a confined aquifer. Alignment consists of multiple horizontal curves including small radius curves (r=210 m) at shafts breakthrough. An unexpected boulder cluster lead the contractor to experience extreme damages to the screw conveyor, RFJ system and causing a crack in main motor plate which resulted in losing one of the six main motors. This paper reviews contractor’s solutions and includes discussion on specific claim resolution method used in this project that can be of great value in preparation of specification and GBR for similar projects.

Jun 13, 2021

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Rameshwar Sah, PK GHORUI, LR SINGH, SIVALINGARAJU BARISETTY, SHYAM YADAV

Fly ash is a by-product generated by the combustion of coal in thermal power plants. Its disposal is a major environmental concern for these power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, a substantial quantity remains unutilized. Bentonite is commonly used as binder in the micropelletization of process waste to attain the mechanical strength required for handling and transportation. The present paper deals with the partial replacement of bentonite with fly ash in the micropelletization process without affecting the quality of the micropellets. The mechanisms of both the binders are discussed. The bonding of particles by bentonite is a physical mechanism, while fly-ash bonding is a chemical mechanism. Silica and alumina are the major constituents present in fly ash along with lime. In the presence of water, the alumino-silicates and unhydrated lime present in fly ash undergo a pozzolanic reaction and form cementitious bonds, which hold the particles together. Use of fly ash as alternative binder for bentonite has cost benefits besides providing a better utilization option for fly ash.

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).