Search Documents

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By Glen Frank, David R. Chapman

Determining the number of boulders and cobbles that will be encountered in the tunnel envelope is one of the most difficult problems confronting the geotechnical engineer in the design of tunnels in glacial terrain. This issue is very important to the contractor, both in determining what methods will be used to construct the facilities and the advance rate that can be achieved for the chosen construction methods. The cost of constructing tunnels by pressurized face tunneling techniques is very sensitive to accurate characterization of the very coarse fraction (large cobble and boulder sized clasts), and no standard method is current available for characterizing boulders and cobbles. Careful use of large diameter borings and the sampling and analytical techniques outlined in this paper can provide a means to answer this difficult question. By performing large diameter borings and carefully recording and sampling the cobbles and boulders encountered, an estimate for the amount of these materials present in the formations sampled can be provided. Using this method allows the designer to communicate the expected geologic conditions to the prospective bidders in a manner that is both definitive and defensible. This paper describes the method as it was used in conjunction with the design of a large diameter sewer tunnel in the Columbus, Ohio area.

Jan 1, 2005

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By Justine Ealy, Daniel Yang, Christina Foster

Maintaining stable high walls can be a challenging task. Complex geological and structural features, alteration zones, rock mass properties, and hydrogeological conditions must be well understood to design a safe mining environment. Economic considerations must also be taken into account as the mine operator must provide ore deliveries and protect reserves. However, even when good engineering practices are followed, and proper blasting and mining techniques are implemented, slope movements may still occur. When these slope instabilities are minor, the mine is often able to continue operations with minimal impacts on safety or production. When these occurrences are excessive and coupled with high rates of movement, a robust monitoring system is crucial to continuing mining activities while protecting personnel. This paper summarizes the approach an open pit mine in Nevada took as excessive and rapid high-wall movement was experienced in an integral area. Creative mining approaches, combined with slope monitoring radar technology, were utilized to maintain safe and successful mining activities despite active movement that exceeded an average velocity of 30 inches per day.

Feb 1, 2024

By Fabio Mielli

Encompassing between 20 and 40 percent of the typical mining operational costs, energy in mining operations is a growing concern for the industry. However, this concern is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. Managing energy efficiency is becoming a keystone of successful companies. The suggested energy strategy in mining and mineral processing operations must follow a well-structured approach to include the following: ? Understanding where energy is being used and why. ? Recommending and implementing energy conservation measures. ? Driving visibility to targets and results. ? Leveraging the energy spent across the enterprise. ? Developing a robust energy and sustainability strategy. Additionally, it must ensure that all decisions support the financial and operational integrity of the business.

Jan 1, 2012

By D. T. Iseley, David Bennett, Christopher Norris

The microtunneling test program is one of three main elements of the research project, "Trenchless Construction: Evaluation of Methods and Materials to Install and Rehabilitate Underground Utilities." The other elements of this project include an evaluation and demonstration of horizontal directional drilling technology and pipeline rehabilitation systems. The research is a Corps and Industry cost-shared project funded under the Construction Productivity Advancement Research (CPAR) program. The laboratory partner is the U.S. Army Engineer Waterways Experiment Station (WES), Geotechnical Laboratory. The industry partner is the Louisiana Tech University's Trenchless Technology Center. Industry participants are contributing over half the total cost of this research. The overall objective of the CPAR program is to improve productivity in the U.S. construction industry, thereby enhancing the competitiveness of the U.S. industry in domestic and overseas markets. The Corps and other federal and state agencies will benefit by realizing reduced costs, enhanced safety and better products and services as the products of this research program are developed, tested, and pushed into the market place. The microtunneling demonstrations and evaluations were performed during September and October 1992 at a specially constructed test facility built at WES in Vicksburg, MS. The test facility is 104 m (340-ft) long, 5 m (16-ft) wide, and 4 m (13-ft) deep. It was constructed, ironically, by first excavating a trench into which 6 different types of soils were placed and compacted in approximately 18.3 m (60-ft) long sections. The soil profiles include a lean silty clay (loess), a dry sand, highly plastic buckshot clay, wet sand, clay gravel and silt. The interfaces between soil profiles were sloped to simulate mixed face conditions as the machines exit one zone and enter another, and provided challenges to ground control and alignment and grade control during these transitions. Moisture and density tests were performed on all materials in each lift to assure uniformity. Horizontal inclinometers and 3 levels of settlement plates were installed at key locations in the test bed. The settlement plates and rods and the horizontal inclinometers, together with surface survey points, provided data to evaluate settlement and heave along the test section. Penetration resistance was measured in each section of the completed test bed. Strain gages were installed in 8 of the 0.6 m (24 in.) diam. Hobas pipe sections to measure strains in the pipe as it was being jacked into place. Steering jack loads, jacking thrust loads, and cutterhead torque were also measured during the drives. The results of these tests will be used together with other information to develop guidelines for conducting feasibility studies and selecting proper methods compatible with anticipated conditions.

Jan 1, 1993

By Martin F. Grier

The Mt Todd Gold Project is located 300km to the south of Darwin in the Northern Territory of Australia. The identified resource comprises 46 million tonnes at 1. 65g/t using a 1. 0g/t cut-off ( 50 million short tonnes at 0.05oz/st). The resource is open to the north and at depth. Mineralisation comprises easterly dipping sheeted quartz/sulphide veins, typically 10 to 20 millimetres in thickness, hosted by hornsfelled greywackes. The majority of the ore body is primary ore with only 10% classified as oxide ore. Early testwork showed that the ore was not suitable for heap leaching, giving only 50% recovery at a -3mm crush size. Acceptable recoveries were obtained at a P80 of 75 micron. However, the ore is extremely hard.

Jan 1, 1992

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By Ali Jaberi Zamharir, Abolfazl Shoghian‐Alanaghi, Hossein Aghajani, Arvin Taghizadeh Tabrizi

In this study, the leaching rate of molybdenite concentrate was evaluated in sulfuric medium, and the influence of the diverse oxidants including hydrogen peroxide, manganese oxide, copper sulfate on the leaching rate was studied. Also, the effect of the addition of the ethylene glycol to the hydrogen peroxide was studied and results showed that with the addition of ethylene glycol, the leaching rate is increased 55% from 41% up to 80.3%. The optimum condition is achieved as 0.7 M of H2SO4, 4.4 M of H2O2, and 3.5 M of EG at 30 °C within 4 h of leaching time and 500 rpm. Also, inserting the oxygen with the pressure of 6 bar to the leaching autoclave, the leaching rate is increased more up to 86.4%. Finally, the leaching process was studied kinetically and the determined mode of controlling factor was specified based on the activation energy which equals 46.252 kJ/mole indicating the chemical reaction mode.

Jun 5, 2022

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By A. K. Dikshit, H. R. Murty, S. K. Gupta

This paper deals with the development of environment performance indicators (EPIs) for the steel industry. Environmental performance has become one of the key measures of business success. Emergence of continuing pressure from customers, employees, government and NGOs for environmental performance evaluation (EPE) of industries has led to evolve a framework for the development of sector specific environmental performance indicators. EPIs can be used by steel industry for assessing the continual improvement in environmental perfromance, selecting various eco-friendly options, benchmarking, environmental reporting, technology assessment and dissemination, evaluating environmental impacts and building EPIs based environmental management systems. The objective of this paper is to develop EPIs for steel industry and provide framework for development of environmental performance indicators based environmental management system and its integration with the overall management system. An indepth discussion has been presented concerning identification of EPIs, eavaluation of significance of EPIs, their prioritization and its integration with Environmental Management Systems. A new methodology has been proposed for implementing EPIs based environmental management systems . The material presented is derived in part from PhD studies of Rajesh Kumar Singh.

Jan 1, 2005

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972