Search Documents

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By Charles C. Dahl, Gordon C. Presley, Andrew E. Nevin, Bruce A. Kennedy

How does SME-AIME cope with profound changes in technology, markets - and most importantly - in employment patterns facing its membership today? This is the question that prompted the Society's Board of Directors to appoint a Long-Range Planning Commission (LRPC) (see ME, Feb. 1984, pp. 118 and 128). This is also the question addressed most particularly by the LRPC's Scope Committee. The Committee started its deliberations by asking such basic questions as "Who are we?" and "What is our business?" The Scope Committee then reviewed the findings and recommendations of other more specialized committees to develop and integrate their concepts of the Society's business for the next 10 years. The policy-making suggestions of the LRPC were reviewed and acted upon by the Board of Directors at its open meeting in Los Angeles on Feb. 26, 1984. At the Oct. 23-26, 1984 SME Fall Meeting in Denver, the Board will again review LRPC recommendations. In answer to the question "Who are we?" the Scope Committee proposed description, which was accepted by vote of the board of directors: . . A technical and professional organization that consists of individual members, namely those mining engineers, metallurgists, geologists, earth scientists, economists, managers, educators, and other professionals concerned with all facets of exploration, production, distribution, and using of mineral commodities. "These mineral commodities include all metals; industrial minerals, including construction materials and fertilizers; coal, oil shales, tar sands, and other mined fuels. Among the earth's mineral resources, only wellpumped oil and gas lie outside the Society's specific purview. "Traditionally, SME members work in the fields of engineering, technology, exploration and discovery, development, construction, mining, quarrying, beneficiation and processing, handling and transport, equipment manufacturing, sales and marketing, data processing, safety, land reclamation, environmental protection, taxation, administration, and management of these elements. "Members practice their professions in industry, in universities and research institutions, and in government. They may be operators, manufacturers, sales persons, contractors, consultants, analysts, researchers, educators, advisors, regulators, or members of supporting staffs. "The members of the Society are leaders in dedication to their crafts, in innovation, and in the pursuit of excellence. Among their numbers they count the most distinguished of engineers, applied scientists, and managers. "The Society is based in the United States, is active on a worldwide basis, and is open to nationals of any country. Certain qualifications must be met for attaining and maintaining membership." Purpose of the Society As to the question "What is our business?" the Scope Committee restated our purpose in light of current practice and the constitution of AIME and the bylaws of AIME and SME. The Board of Directors accepted the following proposed purpose of SME: "To further the professional development and well-being of its members by publishing and distributing technical writings, news, and information; by sponsoring meetings of members; by providing forums for discussions and for continuing education; and by fostering communication on the subjects within its purview. "The Society assists educa-

Jan 4, 1984

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By R. Maurice King

In the operation of today's large scale ore-processing mills, it is extremely important to have some way of making an objective evalu¬ation of the performance of the available flotation reagents. Attempts to do this may often result in inconclusive findings since the magnitude of the difference in the mill results for any two reagents is apt to be quite small compared to the variability introduced by the process and 'the analytical procedures used to measure them. In cases where two reagents give vastly; different mill results, evaluation becomes a simple matter and as such deserves no further attention here. A question of primary concern, however, is how a mill can go about evaluating the performance of two reagents which may, for example, give a difference of only 0.001% copper in the-tailings or of 0.2% in copper recovery. The casual observer may feel that such small differences may be of little importance, but in a mill-whose daily tonnage is between 30 and 40 thousand, these differences could mean a substantial savings. Before the presentation of an actual example of a reagent testing scheme designed for just this-purpose, perhaps a few minutes should be devoted to a review of some statistical methodology to be used later in the discussion.

Jan 1, 1964

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

By Daniel A. Payne

For many years underground mining in the Sydney Coalfield has suffered from the effects of high horizontal stresses. It is only in the last 15 years that they have come to be recognized, understood, predicted and even avoided. This paper relates experiences in three coal mines in three different seams in the Sydney Coalfield. The effect of the direction of the principal horizontal stress on the direction of drivage of gate roads, access roadways and longwalls is described. Results of a monitoring program to measure the change of magnitude and direction of the principal horizontal stress in the gate roads as a result of longwall mining are also presented as well as the effect of the direction of principal horizontal stress on the shape of sandstone/gas outburst cavities.

Jan 1, 1998

By Barbara J. Arnold

Combat Infantrymen’s Badge and Bronze Star Medal. Following his discharge from the Army, he re-entered SDSM&T in 1946 and earned a B.S. degree in Metallurgical Engineering in 1948. He then received an M.S. from Montana Tech (MT), worked several years in industry and then as an Assistant Professor at the University of Washington (Seattle). He joined his Montana Tech colleague, Douglas W. Fuerstenau, at The Massachusetts Institute of Technology (MIT), receiving his doctorate in 1957. While at MIT, he married Clare M. Donaghue of Dorchester, Massachusetts, in 1955

Jan 3, 2022

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By Bruce Hebblewhite

This paper focuses on the recent achievements and practices developed through the Minerals Tertiary Education Council (MTEC) initiative of the Minerals Council of Australia (MCA), in conjunction with the three partner universities involved in mining engineering education – University of New South Wales (UNSW), West Australian School of Mines, Curtin University (WASM), and University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and development of a number of flexible, distance-based delivery programs. The paper will then move on to future initiatives. Importantly, the exciting challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering – Mining Education Australia (MEA). This will provide a common 3rd and 4th year program to all three universities from 2007, involving innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process. Such an initiative is not without its challenges, and has a long way to go, before becoming a reality. However, it offers greater attractiveness and marketing potential to prospective students, as well as economic efficiencies, whilst delivering a better quality, and hopefully greater quantity of graduates to industry. It can also form a launching platform for a much greater level of international collaboration, through a proposed International Mining Education Network (IMEN) which is currently being floated amongst a number of international educators.

Jan 1, 2005

By Julián M. Ortiz, Antoine Caté, Oy Leuangthong, Ilkay S. Cevik

Mineral resource classification relies on the expert assessment of a qualified person (QP) to determine which blocks of a 3D mineral resource model are classified as measured, indicated, or inferred. The decision is often based on a combination of quantitative parameters related to the estimation process and qualitative decisions based on previous experience or preconceptions not captured in the numerical model. As such, the procedure is subject to inconsistency, that is, blocks with similar qualities may end up in different categories, mainly due to the subjective nature of the approach. In this paper, we present a methodology to assist the qualified person in this task by clustering blocks with similar parameters and then classifying them into categories in a consistent and automatic manner that only requires the specification of a few hyper-parameters. The result is a consistent classification into resource categories comparable to the result of a classification done by a qualified person but fully consistent and generated in a short time frame. The procedure begins with repeatedly sub-sampling the block model to determine a distance matrix using an unsupervised random forest approach and then clustering the blocks using the associated distance matrix. Then, all the blocks in the model are classified using a supervised random forest approach, which gives a probability of belonging to each class. The initial class can be determined from the class probabilities. Support vector classification with a radial basis function kernel is utilized to smooth the boundaries between classes and define the final classification. An approach to tune the hyper-parameters of smoothing is provided. The methodology is demonstrated with two examples from two gold deposits. Results are comparable to the classification done by the project qualified person using conventional methods.

Aug 17, 2021

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By T. B. Acton

There are two types of ore transportation systems in use at Newmont's Magma Copper Co. San Manuel mine in Arizona-rail-mounted, box-type rotary cars and the newer rail-mounted, bottom-dumping ASEA cars. Though the cost per car for the ASEA units greatly exceeds the cost per rotary car, the advantages of the ASEA units, including much faster dump times, have made the ASEA system a successful alternative at the San Manuel mine. The rotary system of ore transportation has been in use at San Manuel since production began in 1956. The system employs 7.9-m3 box-type cars to transport ore by rail to shaft pocket areas. A rotating dumping mechanism turns three cars at a time upside down to empty them, and returns them to an upright position. Trains of 15 cars each are dumped in about six minutes. Each 15-car train is pulled by an 18-t rated trolley locomotive. There are about 400 rotary cars in service at San Manuel and the system is used for the majority of ore haulage. This well-proven rotary method was instrumental in achieving the December 1977 world record of 272 Mt hoisted from an underground copper mine. Magma Copper Co. began using ASEA cars in late 1977. Designed by ASEA of Sweden, the cars are built for San Manuel by Kasper-Hall Manufacturing Co. in Tucson. The cars basic design feature is a hinged floor that opens at the side as the car is pulled through the dump. As it passes over the dump, a fifth wheel attached to the hinged floor (opposite the hinges) travels along a rail in the dump. This rail dips down into the pocket and then returns to track level. As the fifth wheel travels along the rail, the car floor opens, the car dumps, and the floor is then returned to track level. As the car is dumping, the body remains suspended over the pocket by wheel rollers attached to each side of the dump. Trains of 10 cars each are emptied in about 45-50 seconds. Each ASEA train is pulled by an 18-t rated trolley locomotive, adapted at San Manuel to allow it to pass through the ASEA dump. At minimal cost, "wings" are welded to each side of the locomotive. These wings suspend the locomotive over the pocket as the train passes through the dump. Advantages of the ASEA System Major design characteristics of the ASEA and rotary systems are shown in the accompanying table. The comparison points out some of the following advantages demonstrated by the ASEA system. • Faster dumping-An ASEA train dumps in 50 seconds, while a rotary train takes at least six minutes. There is no stopping or starting when dumping an ASEA train. The train enters the dump area, dumps, and leaves in one continuous motion-in contrast to rotary trains which must stop and start five times to dump. With the rotary system, three cars are spotted in the dump mechanism by remote control. When the cars are in place, the train operator activates the dump, the cars are turned over, and then returned to an upright position. This process is repeated until all 15 cars in the train are emptied.

Jan 4, 1980