Search Documents

By M. A. Trevits, G. L. Finfinger

Various methods have been developed through US Bureau of Mines research to remove gas in advance of, during, and subsequent to mining. These include drilling horizontal or cross-measure boreholes from a mine opening, and vertical boreholes stimulated for drainage in advance of mining or for gob gas drainage. Techniques and equipment now exist that allow drilling a borehole at any angle to the vertical, and even along an arc. Stimulation treatments have also been developed that provide for increased gas production capability. This paper describes the long-term production history of five select gas drainage installations. The Bureau of Mines conducted or participated in four studies. The remaining study was conducted by the Equitable Gas Co. Principles of storage, release, and migration of coal bed gases The amount of gas contained within any given area of a coalbed depends on the coal's inherent storage capacity and the physical conditions of the coalbed. The gas storage capacity of coal is primarily a function of rank. As such, it cannot be affected by the presence of drainage holes (Kim, 1977). Certain physical conditions of the coalbed can, however, be changed that will affect the release and migration of gas. By pumping water out of the coalbed through the vertical boreholes, two important changes occur - pressure is reduced and water saturation is lowered. Reducing reservoir pressure releases gas as the coalbed adjusts and equilibrates gas to the change. Increasingly large amounts of gas are released for each incremental decrease in pressure. Lowering the water saturation level raises the permeability of the coalbed to gas and allows the gas to more readily migrate to the wellbore (Kisse and Edwards, 1975). For horizontal boreholes completed near mine openings, the coalbed has already undergone a pressure or water saturation reduction phase. This condition thus allows such boreholes to be highly productive with minimal water production. Case studies of coalbed gas production Pittsburgh Coalbed - Marianna mine 58 A methane drainage study was begun in July 1978 at Bethlehem Mines Corp.'s Marianna mine 58, Marianna, PA (Fig. 1). The work was conducted in a section of the mine that was advanced 1.5 km

Jan 8, 1986

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By P. A. Plunkert

Metallurgical-grade bauxite was imported into the United States from 11 countries in 2004. The principal suppliers of this 10 Mt (11 million st) of imported ore were Jamaica (33 percent), Brazil (25 percent), Guinea(23 percent) and Guyana (11 percent). The average value of imports, cost, insurance and freight (c.i.f.) U.S. ports, was $31/t ($28/st). Calcined refractory-grade bauxite imports were 165kt (182,000 st) with an average value of $146/t ($132/st), c.i.f. U.S. ports. China supplied 70 percent; Guyana, 22

Jan 1, 2005

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977

By Gary N. Weinrich

Large surface mining projects in sparsely populated regions of the West have the potential to create disruptions in an area's social and economic character with potential effects on man that can far outweigh the physical and ecological effects on man's environment. The data and analyses involved in addressing the socioeconomic issues are additional to those traditionally associated with surface coal mining, such as those concerning land reclamation and water quality. Appropriate socioeconomic studies in conjunction with mine-planning can identify the potential problem areas in order that project measures can be taken to maximize the beneficial impacts and minimize the adverse effects of surface coal mining. The information required to conduct such socioeconomic analyses, available data sources, and the applicable analyses are described. Overall impacts of some proposed Western surface mines are summarized and potential mitigating steps discussed.

Jan 1, 1975

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By A. K. Snelgrove

At a time when water resource planning is proceeding on a continental scale, such as the proposed $100 billion North American Water and Power Alliance, which would redistribute water among three nations, including seven provinces of Canada, 35 of the United States, and three States of Mexico, the selection of a single river basin for study may seem to require an apologia. None is offered because of ( 1) the magnitude of the Indus , itself a part of the great Indo-Gangetic Plain drainage system, with Himalayan sources, upon which the thickly populated northern sub-continent of Indo-Pakistan depends for agriculture and hydroelectic power; (2) the extraordinary problems created by dismemberment of the world?s largest irrigation system through legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960; and (3) the herculean effort to contain the twin encroachments of waterlogging and salinization in a basin which faces a shortage of fresh water. The British irrigation system of barrages and canals on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences, due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage.

Jan 1, 1967

By D. W. Olson

Garnet has been used as a gemstone for centuries. However, garnet’s angular fractures, relatively high hardness and specific gravity, being chemically inert and non-toxic and free of crystalline silica, and its ability to be recycled make garnet ideal for many industrial applications. Garnet is the general name given to a group of

Jan 1, 2005

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By Larry A. Enloe

The 16-to-1 milling operation is Sunshine Mining Company&apos;s first new silver and gold producing facility. The 16-to-1 underground mine and mill are located approximately 64 km (40 miles) southwest of Tonopah, Nevada. Ore re- serves in the epithermal vein deposit are estimated at 0.91 Mt (one million st) of ore, at an average silver grade of 206 to 240 g/t (6 to 7 oz/st) and an average gold grade of 1.2 g/t (0.035 oz/st). The underground mine uses a large diameter blasthole stoping system of mining using highly mechanized rubber-tired equipment. The mill uses conventional cyanide leaching with countercurrent decantation and Merrill-Crowe precipitation. The mill start-up was in February 1982 resulting in the first pour of dore&apos; in March 1982. The mill&apos;s present annual production is approximately 31.1 t (1.0 million oz) of silver and 264 kg (8500 oz) of gold.

Jan 1, 1984

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By R. L. Virta

Four companies mined ball clay in four states during 2005. They included H.C. Spinks Clay (owned by Franklin Minerals), Kentucky-Tennessee Clay (owned by Imerys), Old Hickory Clay and Unimin. Production was estimated to be 1.32 Mt (1.45 million st) valued at $53.3 million, based on the results of a preliminary survey of the ball clay industry. Production in 2004 was 1.22 Mt (1.34 million st) valued at $54.1 million. Tennessee was the leading ball clay producer state with 61 percent of domestic production, followed by Texas, Mississippi and Kentucky.

Jan 1, 2006

By Robin J. Hickson

El Abra is one of the world’s premier copper de-posits. The project is located in northern Chile, 140 km (87 miles) inland from the Pacific coast. It has the same geologic age and structural setting as the world-class Chuquicamata copper mine located 42 km (26 miles) to the south. The current development plan for El Abra extracts798 Mt (879 million st) of high-quality oxide ore. This will require building a solvent extraction/electrowinning(SX/EW) facility that can produce 225 kt/a (248,000stpy) of cathode copper. This will make El Abra the largest SX/EW copper operation in the world, and the world’s seventh-largest copper producer.

Jan 1, 1996

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.