Search Documents

By John G. Groppo, James C. Hower, Cortland F. Eble, Rick Q. Honaker, Alireza Valian, Stephen F. Greb

Coal and coal combustion byproducts are potential candidates for alternative resources of REEs (rare earth elements). The Illinois Basin is a major coal-producing district in the USA, but little work is available on speciation of REEs in the basin’s coals. In this study, a total number of 382 samples from known locations in the Illinois Basin coal beds were acquired, analyzed for their REE contents, and investigated for any spatial trends or chemical correlations. This study includes Springfield, Herrin, and Baker coal beds—the most heavily mined coals in the basin. An average coal ash from the basin contains 320 ppm REE, with Baker being the highest (407 ppm on average). However, the distribution of REEs in the coal beds was laterally and vertically heterogeneous. A number of trends were found in the REE variations. The most important trend was the relationships of the REE concentrations and fractionations with the distance from the syndepositional sandstones. The total REE concentrations were higher in the proximity of the sandstones, likely due to the increased deposition of detrital material. This increase was the most significant in Springfield coal (90%) and least in Baker (6%). Those coal samples from the Springfield and Herrin coal beds distal from the syndepositional sandstones had a heavy to light REE ratio (H/L ratio) of 0.40 on average, whereas in proximal locations, the ratio was dropped to an average of 0.30. This trend was not significant in the Baker coal bed. In general, higher mineral matter in the coals was associated with higher REEs. In coal preparation plants, refuse rocks can have up to 360 ppmREE. However, the ashes of the cleanest coals had higher REE levels. Such ashes also have a higher ratio of heavy to light REEs. The highest REE concentrations were found in the claystones and the shales associated with the coal beds. Since the naturally occurring calcite, quartz, and pyrite samples were depleted in REEs, an association of REEs with the clay minerals can be suggested.

Jul 20, 2020

By Christophe Bragard

The Los Angeles Metro Eastside Extension light rail project included a 1.5 mile underground segment, which consisted of twin 18'?10" ID tunnels, bored with two EPB-TBMs. One of the major project challenges after the completion of the bored tunnels was the excavation of six cross passages within alluvial geology below the water table and with low ground cover. Sequential excavation methods were employed and this paper details the design, ground treatment, support measures, and construction methods used to mine these cross passages beneath the congested urban streets of the City of Los Angeles.

Jan 1, 2008

By John R. Sturgul, Elizabeth Yost

The number of Native Americans presently working as mining engineers is extremely low-perhaps three in the entire US. At the New Mexico Institute of Mining and Technology, it was felt that introducing high ability students to mining engineering at the high school level would encourage more to consider mining engineering as a career. New Mexico Tech, in Socorro, NM, has initiated a continuing summer college program for Native American high school students. The program, which began in the summer of 1980, is designed to introduce participants to college life, enrich their high school curricula, and expose them to the problems and challenges of a career in mining and related engineering fields. Students From reservations throughout New Mexico with a demonstrated aptitude for science and mathematics were encouraged to apply for admission. Preference was given to high school sophomores and juniors since it is hoped that students will want to return for a second year before graduating from high school and beginning university studies. The program seeks to impress upon the students the need fir Native Americans in the fields of seience and mineral engineering.

Jan 7, 1981

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018

By J. Paraszczak

Underground metal mining involves many challenges. Economic slowdown, tough international competition and sometimes volatile metal prices put constant pressure on mine operators to increase productivity and to reduce production cost. At the same time, countries such as Canada, the United States and Australia are experiencing skilled labor shortages that might even stall development of certain mine projects. Furthermore, some stages of underground production take place in particularly hazardous environments where the safety and health of miners is at risk. Automation of some processes in underground mining is one of the promising avenues to alleviate some of these problems. Loading and haulage are among the most critical operations and areas where implementation of autonomous vehicles has been targeted. However, although health and safety issues are a primary driver to opt for automation, the latter should ensure an acceptable level of productivity and pro?tability. With this in mind, this article focuses on the factors affecting operational effectiveness of autonomous underground loading and haulage equipment and the means to maximize it.

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.IntroductionThe U.S. approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communication with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT).IoT is the network of physical objects, or “things,” embedded with electronics, sensors and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator and/or other connected devices (Atzori, Iera and Morabito, 2010; Gubbi et al. 2013). It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: the Internet and things. The first word pushes toward a network-oriented vision, while the second tends to put the focus on generic objects. The traditional Internet can be viewed as an internet of computers, so things connected to the Internet are computers only. IoT extends the internet by allowing other generic things that are commonly found in daily life, such as refrigerators and cars, to be interconnected through the Internet, thus creating a bridge between the virtual world and the physical world"

Jan 12, 2017

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By Tad S. Golosinski, R. Larry Grayson

Online education is not new. During the last decade, it has reached the stage where many universities offer a variety of courses, degrees and programs without any associated residency requirements. The most successful of the online universities, University of Phoenix, offers hundreds of accredited programs for close to 100,000 students throughout the world (www.phoenix.edu). Online education is considered to be a valid equivalent to traditional, classroom-based education. It is best suited to the needs of mature students with full-time jobs and a desire to deepen their knowledge. While most of the e-business has experienced severe setbacks during the last two years, e-education shows no signs of slowing down. On the contrary, the number of students and institutions offering online education keeps growing. The value of e-education associated expenditures was expected to reach $300 billion in 2001 (Sanoff,2001), making it a serious and mature industry.

Jan 1, 2002

By G. Bierie

The conveying of bulk materials is prone to problems. These problems can reduce the capacity and efficiency of the plant, and even threaten the health and safety of the workforce. This presentation will look at new conveyor technologies systems, and how, used separately or in combination, they can improve material handling.

Jan 1, 2007

By Cheng Xie, Zhihu Li, Xiaoming Sun, Linsen He, Jiaxu Ding, Jinkun Yang, Yong Zhang, Zhenmin Qi

To solve the problem of large deformation of deep soft rock roadway, taking the soft rock roadway of no. 1 coal mine in New Shanghai as an engineering example, the deformation mechanism of surrounding rock of deep soft rock roadway is analyzed by combining theoretical analysis, numerical simulation and field test, and the control countermeasures centering on deep and shallow dense drilling are put forward. Through theoretical derivation, based on the masonry beam theory, surrounding rock structure S-R stability principle and composite beam principle, the length, angle, and spacing of deep and shallow dense drilling are determined. Through numerical simulation, the deformation evolution process of soft rock roadway surrounding rock after dense drilling pressure relief is reproduced, and the influence of drilling parameters (drilling spacing, dip angle) on pressure relief effect is analyzed and compared. The field application test and monitoring verify that the deformation control measures of deep and shallow dense drilling broken roof surrounding rock have a good effect of large deformation control of soft rock roadway, and provide a new support means for the safety and stability control of soft rock roadway.

Mar 2, 2024

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By Yuting Xue, Brijes Mishra

The relaxation test on sandstone specimens showed typical behavior in pre-failure region and stepwise behavior in the postfailure region. Overall, more significant stress relaxation occurred within the failed specimens than the intact ones. Numerical simulations were conducted with pre-defined failure plane and with Voronoi tessellation to visualize the relaxation behavior. The model with pre-defined failure plane showed the key role of failure plane and asperity in simulating the step-wise post-failure relaxation behavior. The inhomogeneous stress distribution within failed specimen and the viscous deformation of intact rocks induced high stress concentration at the asperities. The observed step-wise relaxation initiated from the failure of asperity. Furthermore, the simulations with Voronoi tessellation showed time-dependent fracture development during relaxation in post-failure region. The presence of fractures completely changed the stress distribution. Stress concentration occurred at the front area of fractures and at the interacting areas between fractures. During relaxation, fractures still developed with time and the sudden significant increase in the “damage” coincided with the acceleration of stress relaxation leading to step-wise relaxation. Finally, the results showed the possibility of using residual strength as the long-term strength of failed rock.

Jun 25, 2020

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By M. Albrecht

In the mining industry and particularly in the processing plants, we use some large and unusual equipment. Understanding what it is and what it does is important to good operations, but how do you teach a new employee. When I started out in this field, the information on the processing equipment was easy to come by. Equipment manufacturers readily supplied it; their salesmen, often engineers themselves, knew how important the availability of this information was. Old engineers used their notebooks to train the new engineers. Over time this has changed. Equipment manufacturers have changed hands or gone out of business, and often the older engineers are gone. As a start in reversing this, this presentation will be an introduction to sizing, selecting, and operation of some of this equipment, in particular gravity separating equipment. Major portions of this have been excerpted from A Mining Engineers Notebook: Mineral processing (2).

Feb 23, 2014

By A. A. Bilgin

The prevention of acid mine drainage (AMD) in situ is more attractive than down-gradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied to an abandoned coal mine pool in Pennsylvania. The pool had a pH of 3.0 to 3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by the enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2007