Search Documents

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By S. C. Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by U.S. Department of Energy, designed to demonstrate the safe containment for disposal of radioactive waste. A mine (repository) is currently being developed 2150 feet below the surface, in a thick salt bed which will serve as the disposal medium. Provision of a proper ventilation system at the WIPP Project is a major priority of those responsible for its design, management, and operations. As an ongoing effort towards this goal, it was decided to simulate the mine's ventilation system using Dravo's MINEVENT computer program. Specifically, the work included the development of the following simulation models: 1. Simulation of the current ventilation system 2. Simulation of the designed ventilation system for the following modes: o Mine Construction mode/shift o Waste storage mode/shift o Fire or exhaust filtration mode These computer models are useful in solving complex ventilation problems likely to be encountered in an R&D project, like WIPP. They are particularly helpful for the development of contingency plans to incorporate during emergency situations, such as fires, fan stop- pages, radiation leaks, etc. Also, they can be utilized when considering expanding certain underground areas to ensure the availability of adequate ventilation.

Jan 1, 1986

By Daniel Lakovic

"Mining operations can create a negative environmental impact, especially when considering the tailings that are produced through the processing of ores. Tailings are finely grained residues that form sludges. The tailings are deposited into giant basins, or sludge ponds, where they create a burden on the environmentby limiting the use of processed water.Tailings are one of the most important environmental liabilities for mining operations because of their large proportion in relation to the ore mined — generally 90 to 98 percent. To get to the valuable minerals, mining companies must move large amounts of rock. The rock is ground and then treated, usually with the addition of chemical solutions and large amounts of water. The lower the concentration of the valuable resources, the greater the proportion of accumulated excavated material sludge.Sustainable tailings management requires responsible handling, making it one of the mining industry’s greatest challenges. The proper technology should include consistent control of the environmental risks and impacts, as well as a proper relationship with the communities that surround the mining operations.The tailings, which can remain partly contaminated with chemicals, are pumped into the large sludge basins, which are secured by earthworks. During the mining operations, the basins must be stable enough to withstand the pressure of the stored excavated material. The storage option is still used, but it has failed on occasion. And when it does, it increases the risks to the environment and binds the unused process water. The more complex the availability of fresh water required for industrial use and for human consumption and their economic activities — for example, farming and agriculture — the more complex the conflicts that have the potential to shut down mining operations. With modern separation technology solutions, it’s possible to process the sludge and recover the processed water. However, the responsible use of the water is critical. Therefore, mining companies must rely on technologies that allow for proper reclamation of the water, whether re-using in their own processes or treating it to return it to the environment."

Dec 1, 2018

By Jan L. Reichelderfer, Thomas L. Richardson

Completion of the H-3 Highway Tunnel Project was a critical element in opening this award winning project. The exploratory tunnel was completed as a maintenance tunnel and included difficult shafts extending into the main tunnel cross passages. The project also involved a major addition to the traffic operations center including a deep excavation in close proximity to the tunnel portal structures. The projects also included various completions and improvements to the main tunnels, such as paving, drainage, maintenance, and a variety of critical life-safety issues, such as radio systems, telephones, etc. The highway opened in December 1997.

Jan 1, 2001

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

By Ronald E. Heuer

A 1995 RETC paper of similar title presented a method for estimating rock tunnel water inflow based on semi-empirical correlations with borehole water pressure tests. Since that time the author has found the method to be very useful, and it has been used by others in the industry. This current paper is an update which is intended to: A. More clearly explain assumptions and limitations of the method. B. Describe some case history examples. C. Respond to questions which have been raised; and extend the method to other considerations including distribution of inflow along the tunnel, panning requirements, interpretation of tunnel probe hole water inflow, and estimation of potential effectiveness of pre-excavation grouting to reduce water inflow.

Jan 1, 2005

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By C. G. Clifton

The Oatman District produced approximately 2.2 x 10 6 ounces of gold and 0.8 x 10 ounces of silver between 1897 and 1942. A total of 3.8 x 10 tons of ore averaging 0.58 O/T gold and 0.17 O/T silver was extracted from eight major orebodies and a number of lesser deposits. Oatman lies at the center of a trachyte-latite-rhyolite volcanic complex which contains at least one resurgent caldera. The orebodies are typical epithermal quartz-calcite + adularia lode deposits which are very deficient in sulfur. Ore deposition has occurred within dilatant zones on faults which radiate from a common point within-the complex. Fischer-Watt Mining approached the Oatman District with an integrated exploration program utilizing four basic procedures to define the characteristics of past productive areas the results of which were applied to unexplored portions of the vein system. These procedures, listed in their order of usefulness, in defining known and prospective mineralized zones are: vein contouring, detailed alteration mapping, fluid inclusion temperature determinations, and geochemical sampling.

Jan 1, 1980

By M. William Lallman

Potash production from natural brines of the Bonneville Salt Flats has a comparatively long history dating back to the start of World War I. However, it vas sot until the late 1930's that a successful commercial potash operation was achieved by a firm known as Bonneville Ltd. While improvements in operating techniques, pond design and equipment have been incorporated as they became available it should he understood that the basic technology developed in the late 30's and early 1940's by Bonneville Ltd, for potash production has not been changed significantly. The purpose of this paper is to present a brief review of the history, geology and hydrology of the Bonneville Potash operations and discuss the cur¬rent methods employed for brine collection, solar evaporation and the recovery of potash and other brine chemicals. A detailed study of the hydrogeology of the Bonneville Salt Flats wan made by L. J. Turk,1 Ph.D. thesis for Stanford University in 1969, under the auspices, of Kaiser Chemicals the Industrial Chemicals Division of Kaiser Aluminum & Chemical Corporation. Turk's thesis furnished much of the information presented in this paper.

Jan 1, 1976

By E. M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger miners have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1987

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By W. J. Douglas

The mine manager in today's environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Part III reviewed the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona. Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and a P80 of 6 to 7 µm), pressure leaching at 160ºC with 1,380 kPa (200 psig) oxygen overpressure, DEW to produce LME Grade A cathode, recycling some of the lean electrolyte to the pressure leaching step, and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an acid-autogenous process for pressure leaching. This paper (Part IV) discusses the development and design of a full-scale commercial application for the Morenci operation in Arizona.

Jan 1, 2007

By William H. Mount

Since the late 19405, St. Joe has operated rubber-tired, trackless mining equipment underground in its Southeast Missouri Lead Belt operations. At first, the trackless equipment was operated in conjunction with rail haulage equipment in the room-and-pillar operations, but was to later replace rail haulage completely. The first pieces of equipment to travel on pneumatic rubber tires were short-haul shuttle cars of 12-ton capacity hauling rock from the heading to the mainline railroad. Early-model drill jumbos were the next pieces of production equipment to be carried on rubber, along with mobile slusher ramps. Mobile diesel equipment, in the form of conventional rear-dump trucks, made its appearance underground in the early 1950s, introducing the era of relatively high-speed mobile equipment as compared to the electrically powered shuttle cars. Haulage distances for rubber-tired vehicles were no longer dictated by trolley lines and trailing cables and tires were subjected to increasingly severe applications. St. Joe's first completely trackless mine, the Hayden Creek Mine, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and for the first time, an articulated diesel truck consisting of the tractor unit of a conventional earthmoving scraper and a rear-dump rock wagon. Those machines rolled on the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an In- creasing portion of the underground haulage today.

Jan 1, 1975

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995