Search Documents

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987

By J. L. Porter

This paper takes a personal look, through the author?s own experiences, at the implementation of innovations in the narrow-seam, hard-rock mining environment of South Africa?s mining industry over the past 40 years. A number of examples are used to illustrate some of the successes and failures over this period. More importantly, the examples are used to illustrate that the bulk of the investment for these projects should have been applied in a manner that could have achieved more sustainable results. The use of the word ?technology? in this context is also examined, as it is the author?s contention that only measuring the performance of machinery fails to encapsulate the potential of the entire system describing the scope of the innovation being implemented. These experiences and observations are projected onto the current backdrop of upheaval in the relationship between key industry stakeholders and the sustainability challenges facing areas of the mining sector in the South African economy. The paper concludes with some opinions on where attention can be focused in order to develop new thinking that can be applied for the safe and economic extraction of the nation?s mineral wealth.

Jan 1, 2014

By Alastair S. Macfarlane

The Mineral Resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the Resource, and add measurable value to the Company. The concept of Mineral Resource Management has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of Mineral Resource Management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of Economic Value Added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2007

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By W. C. Joughin

A risk evaluation model has been developed that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment, which is described in Part I (Joughin et al., 2011b). Part II presents the validation of the risk evaluation model. Underground mapping of joints and rockfalls was carried out to provide data for field calibration of the model. This survey was limited to small rockfalls, due to the relatively short period of mapping. Therefore the model was also correlated with rockfall and rockfall injury data collected by mine personnel. The analyses showed that the model provides a reasonable estimate of the expected frequency and size of rockfalls and the frequency of rockfall injuries, but further work is required to enhance the model. Three case studies are presented, which show the benefits of improved support systems from both economic and safety perspectives. This work has demonstrated that the risk evaluation model and the software developed are immediately useful, but further work is required to develop and improve the tools.

Jan 1, 2012

By R. McGregor

You wouldn't start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players can't produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International Power's Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power Hazelwood's (IPRH) experience are: ? that the clear set of project principles and guiding values ensured delivery of a robust plan; ? a robust plan can withstand significant change; and ? value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By N. C. Gay

The quantitative evaluation of the performance of fill materials placed in gold mine stopes is achieved by (i) measurement of the in-situ load- displacement, or stress-strain, characteristics of the materials; (ii) an objective comparison between the observed fill performance and that predicted from suitable computer modelling techniques; and (iii) objectively comparing conditions in backfilled and conventional stopes. Considerable problems have been experienced with the development of sufficiently robust instrumentation which can be installed within filled pad- docks and give reliable information over a long period of time. However, at most mines where backfill performance is being monitored, it has been possible to correlate stress measurements within the filled paddocks with strain measurements adjacent to the paddocks. The resultant stress-strain curves agree relatively well with those determined in the laboratory. Measurements in the hangingwall strata of filled and unfilled stopes indicate that the placement of fill does reduce the amount of inelastic convergence due to bed separation. Moreover, in some stopes, the rate of convergence with respect to face advance does reduce to that of the theoretical elastic convergence. Quantification of changes in the conditions at the stope face due to placement of fill has proved difficult. Observations indicate that, provided the fill is placed close to the face (- 5 m), and adequate temporary face support is used, conditions in filled panels are superior. In addition, in filled panels the damage caused by a rockburst in the stope and, particularly, in gullies is generally much less than would be expected in an unfilled stope. To quantify these improvements, parameters such as stope height, face advance and the frequency of falls of ground are being monitored.

Jan 1, 1988

By Timo Niitti, Sami Grönstrand

n today's marketplace with high metals prices, many operations are faced with the challenge of improving recovery and at the same time maximizing availability. New operations under feasibility studies have the same requirements, with the additional need for ever higher capacities. Economies of scale have proved a vital competitive advantage in the game of ore dressing. Flotation is the most widely used method for extracting valuable minerals from ore - despite its mature age of 100 years. Customer demand has driven the development to increasing cell sizes, and in most cases, this has brought the advantages of both lower capital expenditure and lower operational and maintenance cost. The challenge of scale up, however, is to meet the metallurgical performance requirements in the larger volumes. The paper outlines recent trends and developments in flotation technology, and presents new solutions designed to address the needs for increased capacities as well as improved performance. Whether the goal is to improve existing operations or to scale up new equipment, computer aided tools are playing a key role in shortening the development cycle and reducing costly trial-and-error tests in full scale. Using the new tools and validation thereof will be outlined, as well as the development principles behind the new solutions. Plant results and experiences with the new developments are presented and discussed in several cases around the world.

Jan 1, 2007

By B. B. Mamba, J Ndalamo

The existence of an impressive reserve of oxidized cobalt-copper bearing ores in the African copper belt area lead the GECAMINES (DRC) to develop specific and adapted mineral processing routes (Mulaba-Bafubiandi, 2001). During the conventional diluted sulphuric acid leaching of oxidized cobalt-copper bearing ores commonly referred to as ?heterogenite?, more than 10% cobalt dissolution yield increase was observed in a plant situation (Mwema et al., 2002) when SO2(g) was flushed into the acidified cobalt leaching solution. The present paper attempts to elucidate mechanisms involved which lead to the increase of total cobalt as SO2 is flushed during the leaching of oxidized cobalt bearing minerals. The kinetics of cobalt dissolution as SO2 is flushed into the acidic solution as well as a full characterization, using UV-Visible spectroscopy, of Co2+ and Co3+ species present in the collected leachate are presented while possible effects of the presence of Cu and Fe on the leachability of cobalt bearing minerals present in the oxidised ore will be discussed. In the view of speeding up the leaching process, the mixed cobalt-copper oxidised ores were microwaves pre-processed. Preliminary results were also discussed.

Jan 1, 2007

By C. Kirmanli

The purpose of this paper is to develop an expert system for hydraulic excavator and truck selection in surface mining. Hydraulic excavators and trucks are finding increasing applications in mining operations. Hydraulic excavators are extensively used especially when bringing electricity to rural areas is difficult and for small-scale mining. This paper describes an expert system, which selects the optimum hydraulic excavator truck configuration such that unit production cost is minimized and technical constraints such as geological, geotechnical and mining constraints are satisfied. The system has four modules: user interface, rules and an methods, databases and output module. The expert system in this study is developed within KappaPC shell. It supports object-orientated technology for the MS Windows environment. The software provides a very useful tool to practitioners, saving time and cost. Equipment selection is a recurring and expensive problem of mine planning and often involves interdisciplinary experts from different fields. It is very difficult and expensive to bring together all these experts. The capabilities of the expert system developed are illustrated in the paper. The software overcomes the difficulties of selecting the proper equipment for surface mining operations, which is very important, and results in substantial savings. Equipment databases for hydraulic excavators with 15-59 yd3 capacities and trucks with 35-360 tons are constructed and these databases are used to select the proper configuration. A case study is carried out for Soma Surface Coal mines in Turkey. Keywords: surface mining, expert systems, equipment selection, hydraulic excavators, diggability

Jan 1, 2009

By J. L. Louw

The utilization of centralized blasting systems is progressively becoming a feature of the South African mining industry, owing to increased pressure from the Department of Mineral Resources (DMR) to ensure safer blasting conditions. The purpose of a centralized blasting system (CBS) is to ensure reduced blasting-related incidents and to improve the underground working environment for the mine?s employees. The brief from Samancor Western Chrome Mines (WCM) pertaining to this study was to explore?at a conceptual level?all variables pertaining to the implementation of the CBS. Studies have indicated that Sasol?s SafeBlast? was preferred due to low overall risks and user-friendliness. Empirical observations, however, indicated that attention should be given to the current shaft-clearing procedure and to the installation of additional transformers. This is required to co-ordinate the power supply from 2 level to 10 level with the required supply of the network slave station. A cost analysis indicated that an electronically initiated CBS will result in a R24 cost increase per panel, which relates to a mere 1% cost increase per panel. This cost, in addition to the R1.1 million capital cost, proved to be negligible in comparison to the possible direct and indirect costs incurred by the mine in the event of a blasting-related incident. It was found that Samancor should conduct further studies incorporating the necessary requirements to ensure a successful transition, while considering all stakeholders on the mine. This study proved that the transition to a CBS would ensure safe and efficient blasting at Samancor?s Mooinooi Mine.

Jan 1, 2012

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By K. Tobór-Osadnik, M. Wyganowska, A. Manowska

"The behaviour of employees is an essential issue in the field of occupational health and safety. Safe behaviour is to a large extent determined by, apart from motivation and preventive actions, an employee’s attitude towards hazard. Thus, attention should be given to defining employees’ attitudes, and following that, to the possibility of correcting and shaping these attitudes in relation to hazard and obeying occupational health and safety regulations. The authors have focused on the analysis of employee attitudes to health and safety regulations in Polish coal mining companies, taking into consideration earlier research on the behaviour of selected employees. The paper presents the methods used to identify Z-type (passive) behaviour. Next, this behaviour is analysed to identify differences between a Z-type employee (enslaved) and other employees. To conclude, the paper presents a list of possible motivational tools that may be used to encourage occupational health and safety in Z-type employees. IntroductionThe technical state of equipment and conditions in the workplace greatly influence occupational safety. However, the deciding factor influencing the rate of accidents in the workplace is the frequency with which employees practise risky behaviour. Factors such as the social conditioning of conduct and motivation for organizing safe work conditions have been included in the notion of creating a positive culture of work safety. This notion has been approved as one of the main goals in management (Studenski, 1996).Safe behaviour is to a large extent, apart from motivation and preventive actions, determined by an employee’s attitude towards hazard. All actions undertaken in the field of occupational health and safety, including training, motivational systems, or imitation of behaviour resulting from a high culture of occupational safety in a given work environment, will not bring about the desire effects if workers have an inappropriate attitude towards occupational health and safety regulations."

Jan 1, 2017