Search Documents

By M. Lange

The postulation that primary platinum group metal (PGM) matte will chemically react with magnesia-chrome bricks when temperatures exceed 1500°C was tested. Magnesia-chrome brick samples were heated in contact with matte at 1300°C to 1750°C for 30 minutes, after which the refractory samples were analysed using reflected light microscopy and scanning electron microscopy. The samples were all completely penetrated by matte. As the temperature increased the matte also penetrated the fused aggregate grains and disintegrated them. The chromium concentration of the matte inside the refractory samples was found to be slightly higher than that of the bulk matte. At temperatures of 1500°C and higher, MgO, FeO, and magnesium-rich silicate crystals could be identified in the matte directly adjacent to the refractorymatte interface. Phase relations clearly indicated that chemical reactions take place between primary PGM matte and the magnesiachrome refractory material at temperatures above 1500°C, but that these reactions are more complex than expected from FactSAGE® calculations.

Jan 1, 2014

By J. Yianatos, P. Vallejos

In the last decades, the exponential increase in the cells’ volume resulted in significant advantages such as investment costs, footprint and energy savings. However, in larger size cells, despite the increased diameter/height ratio, new constraints arose related to the need for decreasing the larger froth transport distances to enhance the froth recovery. Thus, the use of froth crowders and internal launders became compulsory to maintain the froth transport distances but decreasing the ratio between gas and collected mineral flowrates. Consequently, the bubble load will increase until reaching a critical bubble surface coverage. In this paper, the concentrate carrying capacity (tph/m2) is described in terms of the bubble surface coverage (bubble loading) at the pulp-froth interface and the froth recovery (froth transport) and is evaluated as a function of the cells’ volume and operating variables. A sensitivity analysis, based on industrial operating and design conditions, such as superficial gas rate, particles size, froth crosssectional area and cells’ volume, was developed for evaluating the metallurgical performance of cells from 100 to 630 m3. Results show that limiting carrying capacity can arise for the whole range of cells’ volume, depending on critical operating conditions, particularly in first rougher cells and cleaning stages of industrial flotation circuits. The increase in cells’ volume consistently increases the bubble loading (bubble surface coverage) under all conditions, approaching the limiting conditions more rapidly in the case of cells without internal launders. Otherwise, the limiting condition was achieved when the particle size DPS decreased from 50 to 20 (μm) and for superficial gas rates significantly less or larger than 1 (cm/s). The use of internal launders allows for increasing the range of the operating conditions needed to reach a certain carrying capacity. Keywords: Bubble carrying capacity, flotation cells, bubble surface coverage, cells’ volume

Jan 1, 2020

By J. J. Cilliers, I. K. Craig, J. D. le Roux, K. Hadler

An analysis of the state-observability characteristics of a dynamic tank-to-tank model of a flotation bank indicates that the concentrate-flow rate of each tank can be estimated from accurate measurements of the pulp height in each tank and the final tailings flow-rate exiting the final tank. Therefore, there is an opportunity to construct an observer (model-based soft-sensor) which can estimate the concentrate flow-rate of tanks in a flotation bank. The concentrate flow-rate, i.e. mass pull, is generally measured by means of froth image analysers on industrial plants. A model-based soft-sensor will not only provide a means to validate froth image analyser results, but could potentially substitute them as they are less expensive to implement and maintain. Keywords: Concentrate flow-rate, estimation, flotation, modelling, observability, soft-sensor

Jan 1, 2020

By A. Marek

The safe and optimal installation of roof support remains one of the biggest challenges in underground mining today. Traditional hand-held, roofbolt installation in conventional mining has been replaced, in a lot of mining operations, by mechanized equipment. This was a first step to moving the operators out of the unsafe working environment and a start on the trend toward a changed support regime in mechanized mining. However, the challenge of handling of the drill steel itself, as well as inserting resin cartridges and bolts, remains a major hazard and the cause of many lost-time injuries. The paper describes and discusses developments in this area, of mechanized bolting and on-board automation, presenting solutions to known problems, achievements to date, and future developments. The solutions presented will identify with addressing customer needs while touching on possibilities for further technology changes, keeping focus on the safety aspect for operators and the need to bring the operators even further away from the unsafe working environment. The-state-of-the-art technology in mechanized bolting equipment is presented and a brief outlook on the past, current, and future developments is given.

Jan 1, 2012

By S. T. L. Harrison, A. Kotsiopoulos, J. R. Amaral Filho, J. L. Broadhurst

The land disposal of voluminous fine-grained tailings from the processing of mined ore bodies poses a long-term risk to the surrounding environment and local communities, while also representing a loss of valuable natural resources; including water, land and mined minerals. To date, the development and practical implementation of alternative approaches and technologies for removing risk and reducing the burden associated with these wastes, particularly in South Africa, remains limited, and value recovery is largely limited to the extraction of precious metals. To this end, researchers at the University of Cape Town have developed a programmatic multi-phased approach to explore and develop opportunities for the valorisation of large-volume mine wastes, based on the innovation value chain. This paper outlines this conceptual approach and presents key outcomes from its application for the specific case of sulfide-bearing coal processing wastes from South African collieries. Through the application of a combination of qualitative and quantitative tools and methodologies, a number of potentially viable opportunities and processing routes for value recovery and bulk re-purposing of these wastes have been identified and tested on a laboratory scale. Studies have, however, also shown that there are several technical and non-technical factors currently constraining commercial application of these opportunities. Overcoming these constraints will require a commitment to innovative waste management approaches and effective multi-sectoral collaboration. Keywords: Coal processing wastes, physical separation, waste re-purposing and utilisation, technology transfer

Jan 1, 2020

By W. P. C. Duyvesteyn, J. R. Cutland, J. R. L. Russell

In 1970 it was decided to build a large new plant at the Chingola Division of N.C.C.M., Ltd., to treat concentrator tailings and leach residues with a low copper content by a leach-solvent extraction-electrowinning process. In order to assist in the establishment of the design parameters for the new plant, and to study the interaction of this plant with the existing leach-electrowinning plant, mathematical models, formulated as linear programs, have been developed and used extensively. The paper outlines the metallurgy of the plants and describes briefly the way in which the models have been formulated and used. The formulation involved the use of separable programming to form the products of some variables.

Jan 1, 2014

By J. H. E. Perry, V. H. Wiik

"The ore deposits of the Zambian Copperbelt occur in sedimentary strata that have been subjected to relatively mild, flexure-type folding. Unrolling serves to reconstruct the original depositional geometry of the folded sedimentary strata and is in common usage on the Copperbelt both for geological analysis of drill hole data and in routine ore reserve estimation.A computerized method of unrolling was introduced at Roan Consolidated Mines in 1969 based on a standard contouring program. A contour map of the geological structure is drawn from a regular grid of elevations, interpolated from the original, irregularly-spaced intersections. Unrolling is performed across this grid, perpendicular to one or two axes specified by the geologist. Each intersection is unrolled independently, and the new co-ordinates are subsequently processed to produce unrolled maps.The technique has been used successfully at RCM over the last two years in both the estimation of ore reserves and exploration planning."

Jan 1, 2014

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

By X. M. Prevost

A computer system to store, retrieve and process coal borehole and analytical data together with other geological, geographical or topographical information is described. As a result of the large volume and variety of data stored since its inception in 1979, as well as the basic versatility of the system, the National Coal Data Base has been performing a number of new tasks for which it was not originally designed. As considerable sets of data are used on almost every project, the use of statistical application programs has become an important processing tool.

Jan 1, 1987

By K. Bryan, O&apos

A 10-year program to integrate crushing and screening models into daily flowsheet design practice has proven successful. A Circuit Analysis Program (CAP) is used worldwide to design and evaluate new and existing crushing flowsheets. To gain user acceptance of CAP and maximize effectiveness, model development, simulation flexibility, ease of use, and developing international access are key issues. These issues have been resolved effectively resulting in flowsheet simulations to assist in justifying increased capital investment. CAP is presently utilized in Canada, United States, and South Africa with intentions to expand to Europe and Asia.

Jan 1, 1987

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By Bosman

Medium suspensions play an integral part in the successful application of dense medium separation for both static and dynamic separators. Although models exist to predict particle movement as a function of medium density and viscosity, these models have been derived on the assumption of Newtonian rheology. Viscosity measurements of medium suspensions have shown that they are non-Newtonian, with a yield stress, and as such cannot be used in the existing models. As a result, medium selection remains an art based upon practical experience and indirect measurements of viscosity such as stability and cyclone differentials.

Jan 1, 2014

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By J. M. Czaplicki

The problems connected with deep mine hoisting and the increasing complexity of this process can be analysed through the application of such mathematical tools as stochastic modelling to study the effectiveness, reliability or safety of hoist methods. To relate these theoretical investigations to real practice, knowledge about components, their stochastic nature and stochastic order of appearance is necessary. This paper presents results obtained during the ten-year (1976-85) period of research undertaken in the Polish mining industry by the Mining Mechanisation Institute of the Silesian Technical University, Gliwice, Poland.

Jan 1, 1987

By B. J. Ralph, I. J. Corrans, B. Harris

In the first section, a brief background to the practical and theoretical aspects of bacterial leaching is presented. Descriptions are given of present and potential methods for exploiting bacterial leaching in metal-winning. In the second section, the results of recent research are presented. The aim of this work was to obtain a greater understanding of the mechanism of bacterial leaching of sulphide minerals. Bacteria were observed to catalyse leaching reactions by oxidising ferrous ions to ferric ions, by removing protective films at the mineral surface and by depolarising cathodic areas.

By A. G. Royle

The reasons for constructing a model of an orebody for which both the parent population and the sampling distribution are known are discussed and details of the model are given. A brief summary of Matheron's theory of regionalized variables is included, with particular reference to his kriging estimators and their variances. Using the model, a comparison is then made between these kriging estimators and other commonly-used estimators. These are compared to find the one with the minimum variance, and an analysis is included to investigate whether any of the estimators is biased. Also included is a comparison between theoretical and experimental variances for some of the estimators.

Jan 1, 2014

By D. J. Adams, R. G. Gürtunca

This paper describes the results obtained from a rock-engineering monitoring programme carried out at West Driefontein gold mine, where dewatered and classified tailings have been used as backfils for local and regional support. The in situ behaviour of these backfils and the surounding rockmass were determined, and it was found that the backfil used on this mine has provided significant regional support. The underground observations also showed less rockburst damage in backfiled panels than in unfiled panels, provided the backfil had been placed properly in the stopes.

Jan 1, 1991

By G. B. Lundstrom

SYNOPSIS For some time, Vaal Reefs South has operated blindhole borers successfully as an integral part of the mining cycle of operations. To date, over 13 000 m of mechanized boxholing has been completed, and from time to time impressive performances have been achieved. The paper describes the machines, the modus operandi, and the structure of the boring organization at the Mine, with some of the results recorded. The Mine recently took delivery of two new machines with interesting design features. The introduction and early experiences with these two machines are also described.

Jan 1, 1985

By V. Matou?vek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007