Search Documents

By A. Muller

The magnesia-carbon refractories used in the ConArc process experience severe wear as a result of the varying slag composition during the blowing phase. This work determines the basicity range in which minimum as well as maximum refractory wear was experienced by the magnesia-carbon refractories during service. In order to determine an optimum slag composition, the crucible test in an induction furnace was used. The magnesia-carbon refractory bricks were cut into cylindrical crucibles to which a synthetic slag in the form of pellets was added. The basicity (B2) of the slag was varied from 0.5 to 3. Tests were done at 1 600°C for one hour. Apart from the crucible test in an induction furnace, visual inspection and SEM analysis were also done to investigate the corrosion mechanism. FACTSage® predictions about the interaction between refractories and slag were also done. These predictions were compared to the actual results attained. It was found that the extent of corrosion by slag attack decreases as the basicity increases. The most severe corrosion of the MgO-C refractories occurred at a basicity of 0.5 whereas the optimum basicity is above 2.0. SEM analysis indicated severe slag attack at the lower basicities with no visible refractory-slag interaction at higher basicities. TheFACTSage® predictions supported most of the actual findings. Keywords Magnesia-carbon, ConArc, blowing phase, slag resistance, induction furnace, crucibles.

Jan 1, 2011

By Jean Michel Marino, Jean-Pierre Slama

"The computer methods used by the French Commissariat a l'Energie Atomique, which are applicable to any type of ore deposits, are:(i) Ore reserve estimation. The data are either the core analyses or gamma leggings. To determine the spatial distribution of the ore, three different methods of interpolation are used. Two of these are based on the least-squares theory and the third one is an application of the regionalized variable theory. The interpretations of the orebody by the geologists are introduced in the computer program as often as possible.(ii) Optimal open pit design. From the spatial distribution of ore, the three-dimensional outlines of the optimal pit are determined by a geometrical algorithm which allows different slopes varying with the azimuth.Finally, the optimization of annual successive plans arc discussed."

Jan 1, 2014

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By D. F. Malan, J. C. Esterhuyse

"Mining in the Carletonville area of the Witwatersrand Basin predates 1934. Owing to the depletion of higher grade ore, the current activities focus increasingly on the extraction of lower grade secondary reefs as well as remnant extraction. Of particular interest is multi-reef remnant extraction. Numerical modelling was conducted to investigate some rock engineering aspects of remnants being understoped on a secondary reef horizon. An analysis of the stress evolution in the middling between two reef horizons indicated that a zone of high major and low minor principal stress develops between the two reefs. This indicates a high risk of violent shear failure. Some pillars were nevertheless successfully understoped in the past and a study was conducted to better understand this phenomenon. An ’extended’ energy release rate concept introduced by Napier and Malan (2014) proved to be useful for investigating this problem. It was found that bedding planes and lithology appears to play a role in the stable dissipation of energy in multi-reef remnant geometries. The study indicated that the stope convergence and the various energy components are affected by the presence, position, and properties of a bedding plane. The energy solutions are complex and sometimes counterintuitive. Care should be exercised when modelling specific cases. The modelling was nevertheless valuable as it indicated that energy dissipated on weak layers may reduce the risk of violent failure in a multi-reef mining scenario. Additional work is required to investigate if crushing on the reef plane plays a prominent role when mining these remnants. IntroductionTo extend the lives of the Witwatersrand gold mines, work is being conducted to include a larger number of remnants and pillars in the reserve base of the mines. According to Jager and Ryder (1999), a remnant is an unmined block of ground surrounded by extensive mining. Remnants are typically left because of adverse or difficult mining conditions caused by geological structures, poor ground conditions, low grade, or rockburst damage (Durrheim, 1997). In contrast, pillars are typically the result of rock engineering designs to control energy release rates (ERR) and seismicity. During the early 1900s, remnants formed by the practice of scattered mining layouts had a significant effect on seismicity. Numerous task teams were appointed during this period. As the industry expanded, the severity of rockbursting increased and the research was formalized after the 1960s. Various recommendations were made and many of these are still used as best practice today (e.g. Jager and Ryder, 1999)."

Dec 1, 2018

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By J. D. Zhou, F. Yang, X. G. Bi

"In this investigation, the phosphorus distribution ratios in the CaF2 system and B2O3 system dephosphorization slags for high-phosphorus hot metal pretreatment were measured by an indirect method under laboratory conditions. Firstly, the phosphorus distribution ratio between liquid slag and solid iron was measured, and then the phosphorus distribution ratio between liquid slag and hot metal was calculated. Phosphorus capacity was calculated in terms of the composition and optical basicity of the slag. Dephosphorization slag was also studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. The experimental results show that the phosphorus capacity of the B2O3 slag system is much greater than that of the CaF2 system. It is demonstrated thatB2O3 can completely replace CaF2 as fluxing agent for high-phosphorus hot metal pretreatment. With CaF2 as fluxing agent, the phosphorus capacity increases with increasing CaO content in the slag, but the phosphorus distribution ratio decreases. B2O3, when used as fluxing agent, can react with high melting point phases such as 2CaO·SiO2 and 3CaO·P2O5 in the slag to form new phases with low melting points such as 11CaO·B2O3.4SiO2, 2CaO·B2O3.SiO2, and Ca9.93(P5.84B0.16O24) (B0.67O1.79), thereby acting as a fluxing agent. When the ratio of w(B2O3)/w(CaO) is 0.16, the phosphorus distribution ratio reaches its maximum value, that is, the dephosphorization ability of the slag is at its maximum. IntroductionAs international iron ore prices continue to rise, the development of China's steel industry is facing a lot of pressure. Against this background, development and utilization of domestic high-phosphorus iron ore resources is particularly important. When highphosphorus iron ore is used in ironmaking, the phosphorus content in the hot metal can reach 0.35% or more, and the hot metal must be pretreated. For hot metal with 0.08–0.10% dissolved phosphorus, the traditional hot metal dephosphorization pretreatment technologies are relatively mature. However, when using these methods to dephosphorize hot metal containing 0.35% P or more, the amount of dephosphorization slag can reach 100–150 kg per ton of hot metal. Furthermore, the traditional dephosphorization methods require the addition of large amounts of CaF2 as fluxing agent, and this results in high fluoride levels in the dephosphorization slag. The fluorine in the slag can partially dissolve in water and thereby causes high fluoride concentration in the water and soil. Once the fluoride is absorbed by humans or animals, it can result in toxic effects on the central nervous system and myocardium. In addition, fluoride can accumulate in the environment, and thereby pose a health risk to animals and humans through the food chain (Li, 2007; Liu, Wang, and Dong, 2011, Diao, 2013). The objective of this research is to replace CaF2 with B2O3 as fluxing agent while achieving the expected goals of hot metal pretreatment."

Jan 1, 2016

By N. V. Nemchinova, A. A. Kozlov, A. V. Epiforov

The gold dissolution in sulfuric acid media during industrial oxidative leaching test of sulfide gold-copper flotation concentrates has been achieved. The reason for this was using technological water containing thiocyanates and cyanides, which can dissolve gold under these conditions. The carbon in column (CIC) process for gold recovery from these solutions was proposed. However, significant amounts of copper and iron were adsorbed onto the carbon during CIC technology industrial tests. This resulted in a decrease of the gold content in the loaded carbon up to 0.5 kg/t. Further development of the technology was conducted by optimisation of gold and impurities stripping and implementation of carbon reactivation. It was shown, that the copper extraction from the loaded carbon during cyanide treatment was about 95%. The copper content in the stripped carbon after cyanide treatment was 1.76 kg/t. The gold recovery during high-pressure elution by caustic solution was 98%. The hydrochloric acidic treatment with thermal pre-treatment (reactivation) for removing iron and calcium from gold-free carbon was proposed. In this case, the iron and calcium extractions from carbon were 40-45 and 50-55% respectively. These tests showed that for carbon recycling the sequence operations of ‘cyanide treatment, gold elution, thermal pre-treatment, hydrochloric acidic treatment’ can be used. Keywords: Thiocyanate leaching, recovery of gold, carbon adsorption, gold elution, copper stripping, thermal reactivation of carbon, activated carbon, carbon-in-column

Jan 1, 2020

By R. V. Ramani, R. Stefanko

"The favorable mining conditions in the United States of America that resulted in the development of the highly productive room and pillar systems are largely disappearing. Increasing mechanization, poorer natural conditions, and greater concern for health, safety and environment gave impetus to the enactment of the Federal Coal Mine Health and Safety Act of 1969. These regulations prescribe more stringent requirements in face ventilation and mine air distribution, necessitating significant changes in existing ventilation systems. Stringent mandatory standards were applied to respirable dust control for the first time, and simultaneous control of both gas and dust has affected the face as well as primary distribution, most notably on haulage entries.The size and complexity of the present-day mining operations, and the need to evaluate various system changes in a limited time, call for scientific methods in mine planning. In this paper, the authors trace the previous applications of computers to mine ventilation planning and discuss the results of their work in applying a ventilation simulator developed at Penn State. The paper includes an analysis of current trends and suggestions for future research and development."

Jan 1, 2014

By R. S. Young

There can be very few members of the Institute who failed to appreciate this extremely interesting and informative paper by Mr Rohrmann of Highveld Steel and Vanadium Corporation. This story of vanadium in South Africa has a very wide appeal to members of our profession: it embraces both ferrous and non-ferrous metallurgy, and both hydrometallurgy and pyrometallurgy. In a comparatively short time, South Africa has become one of the the world's leading producers of vanadium.

Jan 1, 1985

By L. Thomas, A. Argyn, B. Mbao, G. Longo Banza

Since the first application of solvent extraction as part of the hydrometallurgical processing of copper, several studies have been carried out to optimize extractant formulations. In 2006, Solvay developed the ACORGA® OPT series of solvent-extraction reagents to optimize copper transfer by use of a blended formulation containing both aldoxime and ketoxime as well as selected modifiers. The incorporation of selected modifiers in these blended reagents resulted in increased copper transfer, due to the interaction between the modifier and oximes within the blend. By changing the ketoxime concentration and ratio of modifier to aldoxime, the strength of the formulation was optimized to enhance copper transfer and improve Cu:Fe selectivity. This formulation is well known in the African region under the ACORGA® OPT5540 name and provides the best performance at the conditions of agitated leach plants with pregnant leach solutions that fluctuate in Cu grade and pH. This paper discusses advantages of using ACORGA® OPT5540 in the Copperbelt

Jan 1, 2023

By F. Nakhaei, A. Noury, S. Ghodrati

To achieve maximum efficiency in any purification stage, the flotation should be continued until the concentrate grade reaches the feed grade. During sampling from rougher cells of the Iranian Sarcheshmeh copper concentrator plant 1, it was revealed that the concentrate grade of the last five cells of rougher circuit was close to feed grade. Therefore, it was suggested that the concentrate of the aforementioned cells be mixed with rougher feed. In this study, one of eight rougher circuit rows was selected and evaluated. The floatability tests were performed to compare the flotation behaviour of rougher feed and mixture of concentrate of the last five cells with rougher feed in the laboratory scale by a tree analysis process. The results showed that mixing of rougher last five cell concentrate with feed has a detrimental effect on flotation efficiency that leads to a 3% decrease in recovery. It was also observed that with grinding of this concentrate, recovery can be improved. Keywords: Efficiency, flotation, rougher, tree analysis, floatability, concentrate, mixing

Jan 1, 2020

By T. Mützea, L. Schützenmeister, G. Kacheb

High-Pressure Grinding Rolls (HPGR) are employed in cement plants worldwide. Although the technology has been mastered in the majority of applications, design-, scale-up- and operationalchallenges still exist today. In addition to modelling throughput, energy requirement and comminution success, the prediction and avoidance of malfunctions is of great importance in current research. The performance of the mill is highly influenced by the roll speed and the fineness of the feed material. Another parameter influencing the composition of mill feed is the circulating load, which is determined by the grinding circuit configuration, the target fineness and the separation efficiency of the classifier. In order to meet this circumstance and simultaneously maintain a reasonable level of material input and testing effort, a complete grinding circuit on a small technical scale was set up in the research centre of Thyssenkrupp Industrial Solutions AG. The present study varied the roll speed (0.5-2 m/s) and the proportion of fines in the feed (0-75 %) in order to investigate the influence of both parameters on the finish grinding of a Portland cement with a target fineness of 4000 cm²/g according to Blain. The experimental results are compared with model concepts and critically examined with regard to their transferability to industrial plants. Keywords: Cement grinding, grinding circuit, HPGR

Jan 1, 2020

By A. V. Rasskazova

Theoretical substantiation of leaching of clustered ultra-fine gold by the electro-photo activated cyanide and chloride solutions is given in the paper; and processes of activation of leach solution by electrolysis and photo-activation are described. Comparative experiments on electro-photo activated leaching of ultra-fine gold from refractory ores by cyanide and chloride solutions were carried out. The material for research is primary ore of the Pogromnoe deposit (Russian Federation, Trans-Baikal Territory). The ore is characterised by the minimum sulfide minerals and the organic carbon content. Gold in ores of this deposit is presented as mainly ultra-fine. Gold inclusions in quartz and silica-alumina minerals (metasomatic minerals) are ultra-fine. Sulfide minerals (2.5-3%) are presented in ore generally by pyrrhotine (gold content does not exceed 10 g/t). Standard cyanide technology provides 49.5% gold recovery. Photo-electro activated air saturated NaCN provides 69.9% gold recovery. Laboratory research of chloride-hypochlorite column leaching demonstrated that the electro-photo activated method provided 78.9 % gold recovery to pregnant leach solution. Chloride-hypochlorite photo-electro activated solution can provide higher level of gold recovery with shorter process duration (10 days) in comparison with cyanide (40 days). The final decision regarding the choice of leach solution has to be done on the basis of technical and economic calculations. Keywords: Ultra-fine gold, cluster chemical reactions, active clusters, leaching, electro-photo activation of leach solution

Jan 1, 2020

By S. T. L. Harrison, M. Smart, C. J. Edward

Biooxidation, a biohydrometallurgical process, utilizes a mixed microbial consortium to mediate the dissolution of refractory gold-bearing ores to enhance gold recovery during cyanidation. Recognition of water as a critical resource has prompted improved water management strategies within mining and minerals processing. Bioremediated wastewater from the cyanidation tailings provides a potential water source to supplement the water required for the biooxidation circuit, reducing freshwater extraction. Gold biomining operations have typically been reluctant to recycle this wastewater due to the potential inhibitory effects of cyanide and thiocyanate (SCN-) on the microbial population. Historical process upsets suggest that the microorganisms are sensitive to SCN- concentrations as low as 1 mg/L. However, effective bioremediation processes resulting in effluents with low or negligible SCN- concentrations may allow gold biomining plants the opportunity to recycle available water. Microbial activity as well as alteration in community structure were monitored as a function of increasing SCN- concentration over the range of 0 mg/L to 5 mg/L to investigate the response of the biooxidation community to potential SCN- spikes resulting from upsets in the remediation process. Appropriate microbial growth and ferrous iron oxidation activity with a nominal shift in community structure were observed at SCN- concentrations up to 1 mg/L. Thiocyanate concentrations above 1 mg/L resulted in the complete inhibition of ferrous iron oxidation activity. This was attributed to Leptospirillum ferriphilum’s sensitivity to SCN-. Exposure to a SCN- concentration of 5 mg/L resulted in a lower cell concentration and a significant increase in growth lag time, and the absence of L. ferriphilum from the microbial population. At. caldus and Ap. cupricumulans were still present at 5 mg/L SCN-, although Ap. cupricumulans was unable to oxidise ferrous iron at this SCN- concentration. It was concluded that recycling bioremediated cyanidation tailings wastewater within the biooxidation circuit is feasible; however, to retain process performance, SCN- concentrations should not exceed 1 mg/L. Keywords: Biooxidation, thiocyanate, water recycling, community structure

Jan 1, 2020

By M. Holuzko, Y. R. Zhang, J. Alexander

The use of dual-energy X-ray transmission (DE-XRT) technology in the mining industry has been developing rapidly in the past decade. In many projects, DE-XRT images are analysed to classify ore and waste in sulphide deposits where the sulphides and non-sulphides have distinct characteristics in density. In the current practice of DE-XRT image processing, every pixel in the image gets classified into two categories, depending on the intensity of the pixel from both low and high energy X-ray response. If the pixel’s intensity is above the threshold curve generated in the high-energy and lowenergy scatter plot, it is classified as “higher density” material, and the remaining pixels are classified as “lower density” material. This paper elaborates on an alternative approach to DE-XRT image processing for in-depth characterisation of samples from a lead-zinc sulphide deposit. The detailed characterisation is achieved by providing density distribution of individual rock using DE-XRT laboratory sorting unit (COMEX) located at the University of British Columbia. Instead of classifying the X-ray images into two different classes from one threshold curve, multiple density classes are created between two threshold curves to generate the density distribution. By manipulating the two threshold curves, we can analyse images of samples obtained at different resolutions of density distribution. If the two threshold curves become infinitely close to each other, it will create a single-threshold scenario similar to the current methods being used in the industry. This method provides the ability to change the threshold curves, hence providing more flexibility on material characterisation based on the needs of the operation. Furthermore, the DE-XRT images from individual rock specimens are compared to the test results from hand-held X-ray fluorescence (XRF) analyser as well as assays of various elements for the same set of samples. The data analysis will provide information regarding ore characteristics and also the theoretical performance of the sensor-based sorting. Keywords: Dual-energy X-ray Transmission (DE-XRT), X-ray fluorescence (XRF), ore characterisation, density distribution

Jan 1, 2020

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By A. W. Cramb

A three-day symposium on the production of clean steel organized by The South African Institute of Mining and Metallurgy, was held in September 1995 at Vanderbijlpark. It was attended by 151 delegates, who represented the whole of the steel industry in South Africa: Iscor Works, Saldanha Steel, Columbus Stainless, Highveld Steel & Vanadium, Iscor Research & Development, University of Pretoria, and Technikon Witwatersrand, as well as the users of steel products were represented. Professor Allan Cramb held the delegates attention with well-presented research and practical information. He obtained excellent interaction with the delegates by responding in depth to the questions put to him during the Symposium. In summary, he emphasized the following aspects of the elimination of defects during the processing of steel in continuously cast materials.

Jan 1, 1996

By G. T. van Rooyen

In this overview of materials engineering, the author, drawing on his long experience from his student days until the present (emeritus professorship), briefly recounts the main developments in this field: dislocation theory, fracture problems, and the development of alternative materials such as ceramics and polymers. He then takes a look at the future, in which he foresees a greater demand for materials engineers, and leading roles for universities and technikons in collaboration with industry.

Jan 1, 1996

By H. Möller, M. Tshibalanganda, C. Taute, A. du Plessis, M. Leary

Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood.

Apr 1, 2021

By H. Vuthaluru, O. Kavianipour, C. -Z. Li, N. Suresh, D. Sahu

The paper describes a CFD model developed for 76mm Dense Medium Cyclone (DMC) using Ansys Fluent Software to gain insights into the separation of particles according to their size and density. The simulation used in this paper includes the Reynolds stress model to predict the turbulence inside the cyclone body. An Eulerian-Eulerian multiphase CFD model was applied to model a number of physical aspects such as the separation of coal particles and the segregation of magnetite media solids. The experimental results generated in a laboratory scale DMC were used for the validation purpose and the predicted results of CFD have been validated for the flow splits of water, magnetite and coal. The simulation results obtained from the Eulerian-Eulerian multiphase model revealed that the prediction agreed with experimental results, and matched reasonably well in terms of the mass flow rates of water, magnetite and coal. Furthermore, the partition curve of the DMC when mapped for the separation of - 3.0+0.50 mm size also showed to be in agreement with the experimentally obtained curves. The gravity of cut (SG50), also predicted by the Eulerian-Eulerain multiphase CFD model, was found to be in the vicinity of observed experimental value of SG50. Keywords: Dense medium cyclone, Eulerian-Eulerain multi-phase modelling, computational fluid dynamics, cut gravity (SG50)

Jan 1, 2020