Search Documents

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By J. Roger Loebenstein

ASARCO Incorporated, the only domestic arsenic producer, terminated copper-smelting operations and the associated recovery of byproduct arsenic trioxide at Tacoma, W A. in 1985. It still shipped small quantities of trioxide from its remaining stocks in 1987. Imports for consumption of arsenic trioxide were slightly higher than in 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1989

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

Provide reasonably priced, reliable fire protection for loading shovels. Approach An automatic fire, sensing and suppression system using both dry chemical and Halon 1301 was developed. It is more rugged than similar industrial-type fire protection systems. How It Works Temperature sensors detect heat from a fire, and trigger the system. These sensors are located inside the machinery house and under the house and shovel frame where it rotates around the crawler chassis ring gear. An alarm is sounded, and extinguishing agents are released either in the machinery house or in the ring gear area. The system can also be triggered by a manual control. If the fire Is detected in the machinery house, all power is shut down to the motor-generator sets, ventilation fan, and all electrical controls. Doors are automatically closed. After a delay to allow time for the ventilation fan to stop, Halon 1301, a gaseous fire extinguishing agent, is released inside the machinery house until it reaches a concentration of about 7 percent. This concentration is sufficient to extinguish a fire, but isn't toxic to personnel

Jan 1, 1980

Reduce longwall equipment transfer time between panels by utilizing a predriven recovery room, and thus eliminate the premove preparation associated with most equipment recovery methods. Background and Approach The recovery point for a retreating longwall is a predetermined position near the end of the panel where mining is terminated and equipment is disassembled and removed. However, to prepare for equipment removal at the recovery point, bolting and wire meshing arc required before the recovery point is reached. Usually, preparations for equipment recovery begin about 35 ft from the recovery point, significantly impeding the normal rate of advance of the longwall and, consequently, production. Recently, BethEnergy Mines, Inc., and the Bureau of Mines cooperated to evaluate the applicability of utilizing predriven recovery rooms to improve longwall equipment recovery. A predriven recovery room is an entry driven parallel to the longwall face at the end of the panel, having standard dimensions (for that particular mine) and supported with bolts, wire mesh, and supplemental support. The preparation of this entry is completed before it experiences mining-induced effects from the approaching longwall face. This enables the face to continue to mine at its normal rate of advance until the panel is completed. The supplemental support is required to control the loads imposed by the front abutment and is the most vital component of the recovery room.

Jan 1, 1989

By Kenneth M. Earl

The purpose of this investigation was to obtain subsurface information on the John Burdette barite-fluorite deposit, Garrard County, Ky. The deposit was intersected in each of five inclined diamond-drill hales aggregating 1,163 feet. All holes were drilled from the hanging wall of the deposit; the inclinations varied from minus 41° to minus 75°. Disseminated metallic sulfides were noted in the drill cores from holes 1, 2, 4, and 5. The deepest drilling was hole 5, which intersected the deposit at approximately 490 feet down dip. Visual inspection of the cores did not indicate mineralization of economic importance; therefore, no chemical analyses were conducted. Condensed logs of diamond-drill cores are included in this report. All drill cores were shipped to the Bureau of Mines core library in Minneapolis, Minn., for future reference,

Jan 1, 1959

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

By Rudolf Kudlich

"SUMMARYThe Ringelmann Smoke Chart fulfills an important need in smoke abatement work and certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous information circular, by Rudolf Kudlich, now are a necessary complement to the chart. More detail regarding the use of the chart is included than was given in the earlier manuscript.INTRODUCTIONThe Ringelmann Smoke Chart, giving shades of gray by which the density of columns of smoke rising from stacks may be compared, was developed by a Professor Ringelmann of Paris. Maximilian Ringelmann, born in 1861, was professor of agricultural engineering at l'Institute National Agronomique and Director de la Station d'Essais de Machines in Paris in 1888, and held those positions for many years thereafter.The chart apparently was introduced into the United States by William Kent in an article published in ""Engineering News"" of November 11, 1897, with a comment that he had learned of it in a private communication from a Bryan Donkin of London. It was said to have come into somewhat extensive use in Europe by that time. Kent proposed in 1899 that it be accepted as the standard measure of smoke density in the standard code for power-plant testing that was being formulated by the American Society of Mechanical Engineers.The Ringelmann Chart was used by the engineers of the Technologic Branch of the Federal Geological Survey (which later formed the nucleus of the present Bureau of Mines) in their studies of smokeless combustion beginning at St. Louis in 1904, and by 1910 had been recognized officially in the smoke ordinance for Boston passed by the Massachusetts Legislature."

Apr 1, 1955

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

Improve the health and safety of underground mine workers by finding ways of keeping them away from unsupported areas of the mine. Background Roof falls have been the leading cause of fatal accidents in the underground coal mining industry. During 1985-89, 92 coal miners were killed by falls of roof and rib, with more than 4,000 miners injured. According to accident investigation reports from the Mine Safety and Health Administration, 47% of the victims of these fatal roof fall accidents were in the area of unsupported roof al the time they were killed. There is an urgent need to find out why miners go under unsupported roof and to devise strategies for preventing this unsafe behavior. Approach To discover what can be done to prevent miners from going under unsupported roof, confidential interviews were conducted with 297 miners who work in the face crews of 6 different coal mines. The interview topics included company policies and actions regarding going under unsupported roof, how foremen react to people who go under unsupported roof, circumstances likely to cause some people to go under unsupported roof and how to prevent these situations, and observations concerning those who go under unsupported root.

Jan 1, 1991

By Kenneth O. Bennington

This investigation is part of the Bureau of Mines research effort directed at advancing mineral technology and minimizing energy requirements for extractive metallurgy. The emplacement of the primary minerals petalite (LiAlSi4010) and spodumene (LiAlSi206) in the lithium pegmatites is examined on the basis of their Gibbs energies of formation determined from lithium metastltcate and oxides, using a series of proposed reactions. The reaction between spodumene, quartz, and petalite (LiAlSi206 + 25i02 [=] LiAlSi4010) apparently does not take place in nature but may be proved experimentally.

Jan 1, 1982

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

By Rollien R. Wells

THERE are two recognized methods of recording the state of the metallurgical art. One involves delineation of individual advances reported in the literature. This approach is used effectively in the excellent annual reviews published by some of the leading technical journals and in the technology sections of the individual commodity chapters in this volume. In an effort to more clearly indicate the current trend of metallurgical research and development, the authors of this chapter chose the method of discussing generally selected items of interest brought to their attention during 1959. Since technology cannot be confined by dates on a calendar, most of the items mentioned have been in the process of development for several years. No attempt was made to identify the sources of information used here. Material was drawn from many sources : Nonconfidential correspondence and conversations with authorities of the metallurgical fraternity, papers delivered at technical meetings, and articles noted in the technical press, including particularly Engineering and Mining Journal, Metal Progress, Journal of Metals, Mining Engineering, Industrial and Engineering Chemistry, Chemical Engineering, Chemical and Engineering News, Chemical Week, Materials in Design Engineering, Review of Metal Literature, the Canadian Mining and Metallurgical Bulletin, the Mining Journal (British), and the Journal of the Institute of Metals (British).

Jan 1, 1960

By Clarence O. Babcock

ROCK BEHAVIOR has proved of national interest in a variety of fields. The behavior of rock consequent to a nuclear blast was used to detect such blasts, as criteria for the design of underground military defense installations that would resist nuclear blasts, and for judging the feasibility for peaceful uses of nuclear explosives. An obvious peaceful application of nuclear explosives would be for large-scale rock excavation, and plans were presented during the year to improve the present Panama Canal or create a new canal by this method. These plans were based largely on earlier crater tests that demonstrated rock behavior when subjected to a buried nuclear blast. A knowledge of rock behavior under impact was used to evaluate the materials of the moon by means of the geometric configurations visible in the close-up pictures of the moon surface taken by the U.S. rocket Ranger 7. The composition of the moon must be considered in devising methods for taking samples of the surface layers or in designing underground shelters as bases for future explorations of the moon.

Jan 1, 1965

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By H. H. Dewing

The Bureau of Mines conducted a laboratory-scale investigation of a technique that produces zinc sulfate and elemental sulfur from sphalerite concentrates by reaction with sulfuric acid at 175° to 200° C and ambient pressure. The objective of the investigation was to develop a hydrometallurgical method of producing zinc from sulfide concentrates that does not generate sulfur dioxide pollutants. Reaction with 80-to 85-pct sulfuric acid produced 4 moles of sulfur for every 3 moles of sphalerite reacted, with minimal production of sulfur gases under optimum conditions. More than 98 pct of the zinc was recovered as zinc sulfate after 3 hours at 175° C. The reaction mixture was leached with simulated spent zinc electrolyte containing 13-pct sulfuric acid to recover zinc sulfate from the insoluble, high-sulfur residue. Neutral zinc sulfate, which is required for electrolysis, was separated from the sulfuric acid solution by crystallization as ZnS04?7H20 at -10° C. Up to 80 pct of the water in the recycled electrolysis solution was removed by the crystallization process; evaporation was used to further concentrate the sulfuric acid for reuse in leaching sphalerite. Advantages of the proposed method over conven-tional roasting and leaching include virtual elimination of sulfur dioxide, production of a solid sulfur byproduct, and higher zinc recoveries due to elimination of zinc ferrite losses.

Jan 1, 1978

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992