Search Documents

By C. B. Manula, R. L. Sanford, R. A. Rivell

Part I. DATA INPUT ALTERNATIVE 1

Jan 1, 1974

By John C. Edwards

A two-dimensional, time-dependent, mathematical model has been developed that describes fire spread along the walls of a ventilated duct. The model is based on the assumption that the leading edge of the fire zone propagating along the wall surface coincides with the isotherm for the fuel ignition temperature. The model includes gas-phase energy transport via radiation and forced convection inside the duct and solid-phase energy transport by conduction into the fuel lining. Product gases emitted from the fire zone are assumed to mix uniformly with the ventilation gas to produce an optically dense gas mixture at the combustion temperature that enters the preheat region. Numerical solutions of the model equations for a coal-lined duct (simulated coal mine entry) have been used to investigate the effects of tube radius, air velocity, combustion temperature, and optical density of the soot-laden gas upon the terminal fire spread rate.

Jan 1, 1977

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1984

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By R. B. Prater

Research by the Bureau of Mines includes efforts to devise means for maximum recovery of critical and strategic metals from primary and secondary domestic resources. As part of that effort, the Bureau developed a hydrometallurgical process to recover Co, Ni, and Cu from Missouri lead-smelter matte. The process includes leaching with H2S04 plus Mn02 as an oxidizing agent, liquor purification, selective precipitation of CuS, (Co,Ni)S, and MnC03, and crystallization of Na2S04&apos; This report is concerned primarily with liquor purification, in which As and Fe are removed from the leach liquor by pH adjustment and filtration. Two variations of the purification step are described. One variation provides liquor containing <1 mg/L As and Fe but requires two solid-liquid separations, The other is achieved with only one solid-liquid separation but leads to a lower degree of purification.

Jan 1, 1987

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Fun-Den Wang

Finite-element structural analyses were performed to determine the stress distribution and displacements around a single rectangular coal mine opening in a multilayered rock system. The effects of changes in mechanical properties of roof and coal layers, roof layer and mine opening geometry, horizontal-to-vertical load ratio, and structural geologic features on the stress distribution about the opening were studied. Variability in the stiffness and relative thickness of the immediate roof layers can produce a considerable difference in the stress distribution about the opening as compared with that of a homogeneous material. Changes in opening width and horizontal-to-vertical load ratio have different effects on the stress distribution about the opening depending on the composition of the roof layers. In general, where a stiff layer exists in the roof at the surface of the opening, the stresses are higher in the roof and ribs around the opening. Horizontal changes in facies in the roof layers produced by structural geologic features can also greatly alter the stress distribution about the opening compared with the simple layered cases.

Jan 1, 1974

By Robert H. Lambeth

The Madison RARE II study area has four prospects with identified resources. These are listed in table 1 and are described in the following text. A high potential for Sillimanite exists at the Placer Creek occurrence (fig. 1, no. 7) and potential for phosphate rack in all areas underlain by the Phosphoria Formation. Some prospects exhibit minor potential for copper, lead, zinc, silver, and gold in the southern portion and very minor potential in the northern portion. Deposits in the northern end also have low potential for rare earth, asbestiform anthophyllite, or kyanite group minerals (including sillimanite).

Jan 1, 1982

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

By Frank A. Peters

This description of process evaluation techniques used by the Bureau of Mines for studying proposed processing techniques has been prepared to provide those interested in using these studies with an understanding of the methodology. The methods used for preparing both capital and operating cost estimates are described. Each step in preparing the evaluations is described. Types of equipment costs are shown and factors used in the estimates are defined. Uses of the estimates are suggested and several examples are included. The accuracy of various types of estimates is discussed, along with an explanation of the reason for selecting the type used in the Bureau&apos;s process evaluation studies.

Jan 1, 1987

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By H. C. Howarth

The preliminary tests referred to in this report wore made at the Bureau&apos;s Experimental Mine under the general supervision of G. S. Rice chief mining engineer, to determine whether rock dust way be used to extinguish or control mine fires. DESCRIPTION OF THE DUST USED The dust used for application by hand was made from draw slate taken from the Experimental Mine. This draw slate was crushed in a hammer-type crusher fitted with 1/16 inch by 2-inch slotted screens. A sizing test of the dust showed 96.5 per cent through 20 mesh, 69.4 per cent through 48 mesh, 46.2 per cent through 100 mesh, end 33.5 per cent through 200 mesh.

Jan 1, 1927

By Bill M. Stewart

The Bureau of Mines conducted laboratory tests to determine the effects on the physical properties of coarse coal waste of adding large amounts of fine coal waste. Maximum laboratory dry density, optimum moisture content, shear strength, and permeability tests were conducted on samples that contained 18 to 60 pct minus No.4 (U.S. Standard sieve size) coal waste. For the nonslaky materials, maximum laboratory densities were highest and permeabilities lowest when the samples contained between 30 and 40 pct minus No.4. Shear strength increased rapidly when the proportion of minus No. 4 was increased from 20 to 40 pct, but then increased only slightly or leveled off when the minus No. 4 was increased to 60 pct. Optimum moisture content and permeability were the physical properties most affected by the addition of fines. Optimum moisture content increased as much as 3 pct, and permeabilities decreased up to three orders of magnitude. Slaky coal waste material had physical property reactions to the addition of fines substantially different from those of nonslaky material.

Jan 1, 1981

By E. J. Matson

The Little Castle Creek chromite deposit was examined in February and May 1941, respectively, by W. O. Vandenburg and O. H. Metzger, engineers of the Bureau of Mines. The Federal Geological Survey started a magnetometer survey of the area in November 1940 and completed its work during April and May 1941. Field work by the Bureau of Mines was conducted during May and June 1941. The purpose of the Bureau of Mines investigation was to search for a continuation of the chromite mineralization. The property at one time was the largest chromite producer in California.

Jan 1, 1949

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach&apos;s equation and Durand&apos;s equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the Bureau of Mines and bound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrow- band through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up- link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 3, 1972

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they&apos;re doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

By Deborah A. Kramer

As part of the Nation&apos;s growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By Howard E. Parkinson, John N. Murphy

Abstract-Underground mines are typically extensive labyrinths that employ many people working over an area of many square miles; exten¬sive analysis of mine-communications systems has identified specific problem areas, in particular the excessive times required to locate key personnel underground, the inadequacy of existing phone systems in terms of capacity and privacy, and the inability to communicate with men on the move with wireless communications, as is taken for granted on the surface. A review is presented of the existing systems, the prob¬lem definition, and the various approaches that have been or are being investigated to solve these problems. Manuscript received June 8, 1977; revised August 28, 1977. The authors are with the Industrial Hazards and Communications group, Pittsburgh Mining and Safety Research Center, Bureau of Mines, U.S. Department of the Interior, Pittsburgh, PA 15213.

Aug 28, 1977