Search Documents

By Thomas J. Peters

This report is part of the U.S. Bureau of Mines Idaho Land Assesment Program to study the mineral resources of priority roadless areas in Idaho. The results of these mineral inventories provide minerals information needed to make wise decisions regarding future land management practices, and to ensure a dependable supply of minerals at a reasonable cost. The 16,300-acre Lionhead area, studied in 1991, lies along the Montana border north of Henrys lake, 10 mi west of West Yellowstone, Montana. The study area includes much of the rugged Henrys Lake Mountains, and is largely covered with conifer forest. Several peaks are over 10,000 ft in elevation. The Lionhead area has been proposed for Wilderness. No mineral resources were identified within or near the Lionhead study area. Five prospects occur in, or within 1 mi of the area: these include 1) an intermittently used road gravel pit, 2) the Thimbleberry lateritic iron prospect, of geologic and historic interest only, 3) the Tick Heaven talc prospect, 4) the Dry Fork garnet prospect, and 5) the lynx prospect, which appears to be of historic interest only. Talc is seen only as float at the Tick Heaven prospect, but the geology is permissive of talc resources at depth. The garnet prospect, and nearby similar alluvial terrane, mainly outside the study area, appears to be the most likely setting to contain mineable resources. Examined workings include four trenches and pits in rock and one gravel pit.

Jan 1, 1992

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By T. G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a porphyry copper sulfide ore. The purpose was to determine the effects on copper leaching of additions of NaCI to a conventional sulfate leach system and to analyze the oxidant requirements and the oxidation products that resulted from leaching of the sulfide minerals in the ore. Baseline sulfate and sulfate plus 2-pct-NaCl-leach-solution experiments employing 167-kg (367-lb) and 152-kg (333-lb) charges, respectively, were conducted. The minus 25.4-cm (10-inch) ore was leached at 90° C under flooded conditions with 2.8 MPa (400 psig) of oxygen bubbling through the system. Sixty-seven pct of the copper was extracted in 1,236 days of leaching in the NaCI experiment, whereas 47 pct of the copper was extracted in 913 days of leaching in the baseline experiment. Diffusion into and out of the ore fragments controlled the rate of leaching, which precluded enhancement of the leach rate by the chloride ions. The calculated oxygen consumption was 3.17 kg/kg of copper extracted in the baseline experiment and 3.46 kg/kg of copper extracted in the experiment to determine the effect of chloride ions.

Jan 1, 1982

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The question as to whether or not the flow of water through pneumatic rock drills commonly used in this country keeps to a minimum dust disseminated into the air during drilling arose during a study of the dust-in-air conditions in Butte mines from February to July 1936 and December 1936 to June 1937 made by the Bureau of Mines in cooperation with the Anaconda Copper Mining Co., Butte, Mont, The purpose of this report is to describe the study, including some experimental work on the subject, and to give test results.ACKNOWLEDGMENTSThe help of the ventilation department of the Anaconda Copper Mining Co. in planning the study and collecting the data is gratefully acknowledged.EXPERIMENTAL CONDITIONSTests were conducted in an untimbered 6- by 8-foot crosscut in medium-hard granitic rock near the shaft station on an inactive level of one of the active Butte mines. Figure 1 shows the plan and section of the test location. Air was drawn from the shaft at the station, through the crosscut, and up through another shaft. The flow of air through the crosscut was decreased by a brattice downstream from the sampling location, so that relatively high, easily measurable dust concentrations would be obtained in the tests. Impinger samples for determing concentration of dust in the air were collected in an opening 51 inches wide, 29 inches high, and about 4o inches from the top of the rails in a wooden stopping about 16 feet downstream from the place where the test holes were drilled."

Apr 1, 1938

By J. E. Pahlman

The Bureau of Mines conducted re-search to determine the resistance of basic refractories to corrosion by ash slags that would result from the burning of coal and lignite in metallurgical operations. Basic refractories are of economic interest because they are from one-third to one-half as expensive as 90-to 99-pct-alumina refractories. Static tests were performed at 1,300° C and dynamic tests at 1,400° to 1,650° C to investigate the stability of refractory specimens in a slag environment. In alkali-containing lignite ash slags, in order of decreasing resistance, magnesite, magnesite-chrome, and chrome-magnesite refractories all had corrosion resistances equal to or better than 90-to 99-pct-alumina refractories. These basic refractories formed slag penetration layers in dynamic tests, which helped protect them from further attack. Chemically bonded basic refractories in general did not have as good a resistance to slag attack as did burned refractories of the same composition. In very acidic coal ash slag, a chrome-magnesite refractory containing 30 pct MgO plus a slag inhibitor and direct-bonded magnesite-chrome refractories with 60 pct MgO had good resistance to attack. Chrome-magnesite refractories (30 to 40 pct MgO) were moderately to severely attacked, and refractories with greater than 70 pct MgO were severely attacked by this same slag.

Jan 1, 1982

Legislation and Government Programs.-On February 4, 1977, the Occupational Safety and Health Administration (OSHA) issued its final environmental impact statement on the occupational use of inorganic arsenic.2 The statement examined the ramifications of the original proposed standard published in the Draft Environmental Impact Statement (DEIS).3 The DEIS proposed to limit the exposure of employees to no more than 4 micrograms of arsenic per cubic meter of air as determined on an 8-hour-time-weighted average basis; or a ceiling limit of 10 micrograms of arsenic per cubic meter of air based on a 15 minute sampling period. The purpose of the proposed regulation is to reduce the risk of smelter workers developing lung and skin cancer as a result of exposure. A comprehensive study compiled by the Committee on Medical and Biologic Effects of Environmental Pollutants concluded that "there is strong epidemiologic evidence that inorganic arsenic is a skin and lung carcinogen in man."' In April 1977, the Environmental Protection Agency (EPA) served notice to ASARCO Incorporated that its Tacoma copper smelter and associated arsenic-producing facilities were in violation of State laws which limit sulfur dioxide and particulate matter emissions. This notice followed the Washington State Pollution Control Hearing Board overturning a prior ruling by the Puget Sound Air Pollution Control Agency (PSAPCA) which had permitted a 5-year variance from the State of Washington air quality standards. In December 1977, ASARCO appealed in court the decision of the Hearing Board.

Jan 1, 1980

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

By Douglas Pollock, John Organiscak

Water spray characteristics, including droplet size and velocity, airborne dust capture potential, and induced airflow quantity for various spray nozzle designs were evaluated to provide basic information for improving spray applications. Water droplet size and velocity characteristics were initially measured by a Phase Doppler Particle Analyzer (PDPA) for hollow cone, full cone, flat fan, and air atomized spray nozzles at similar operating parameters. Airflow inducement and dust capture experiments were also conducted under the same operating parameters to examine any salient features of the spray nozzle type, droplet characteristics, induced airflow, and airborne dust capture. Test results indicate that there are trade offs between airflow inducement and dust capture efficiency. A spray nozzle with a wider discharge angle was observed to induce more airflow, but at reduced dust capture efficiencies. Increasing spray nozzle fluid pressure(s) generally reduced water droplet sizes with concurrent increases in droplet velocity, airflow inducement, and airborne dust capture. Placing a three-sided barrier around the spray nozzles normally reduced spray air induction and increased dust capture efficiency. A direct relationship between airborne dust capture efficiency and spray input power normalized per unit of airflow induced was ob- served. This information can be utilized to improve the performance of water sprays for reducing airborne dust levels.

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

By Basil Dimitriades

The association of automotive fuel composition with exhaust reactivity was studied in an experimental program that involved testing with different automotive engines and with gasolines of varied composition. Results showed clearly the exhaust reactivity to increase with increasing levels of polyalkylbenzenes in the fuel. No other systematic patterns of high significance were detected in the association of exhaust reactivity with several broadly defined groups of fuel components. For the purposes of this study, had it been possible, fuel composition should have been defined and expressed in terms of component groups such that the potential for exhaust reactivity would be the same within each group and different from group to group. Classification of fuel components in terms of the paraffins-olefins-aromatics groups does not meet the latter requirements. For appropriate classification of fuel components more information is needed on the combustion .of hydrocarbons in the multicylinder internal combustion engine. Statistical analysis of the mass emissions data showed significant car and fuel effects on hydrocarbon, carbon monoxide, nitric oxide, total aldehydes, and formaldehyde emission levels and on total photochemical reactivity. Car-fuel interactions were not significant at the 90-pct level. Correlations were found between mass emission parameters and fuel composition.

Jan 1, 1973

By George S. Koch

In preparing diamond-drill core samples for assay at the Homestake mine, Lead, S. Dak., 5-foot intervals of core are processed through three stages, crushing, grinding, and pulverizing, and portions of the core material are discarded after splitting at each stage of preparation. Then two 1-assay-ton fractions are taken from the pulverized material and assayed. This report investigates alternative methods of sample preparation. The consequences of crushing, grinding, and pulverizing all rather than part of the core are appraised through the statistical analysis of assay results from 118 5-foot intervals of core. Evidently, a substantial improvement in precision at small additional expense is obtained by grinding most or all of the core before splitting. Pulverizing all of the core would be desirable only if doing-so would cost less than assaying five random splits from each interval. Graphs and tables detail appropriate procedures to obtain specified precisions. The experimental design and methods can be applied to similar problems in preparing core and other geological samples.

Jan 1, 1972

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By Howard E. Parkinson

A brief description is given of various Bureau of Mines research activities that have begun since July 1974 and are not being reported on by others at the Third West Virginia University (WVU) Conference on Coal Mine Electrotechnology. An essential feature of the various projects is that they are pragmatic. The projects are applied research and are carried out both by the Bureau in-house research group and by other research groups through contract research. Projects have been directed toward wired-type communications with a special effort to modify the wired systems so as to be more effectively used. The projects are in three groups: Pager phone systems, trolley line phone systems, and guided-wire wireless communications. Also, a brief sketch is given of research that is essential for further developments in mine communications. From the early results of these various projects, the Bureau has good reason to project that there will be improved performance of existing communication systems and that communications will be extended to other individuals working in areas that are excluded from present mine communication systems.

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By Thomas P. Holden, Todd M. Ruff

Problem: An average of three workers a year are killed in surface mining operations when a piece of haulage equipment collides with another smaller vehicle or a worker on foot. Another three workers are killed each year when haulage equipment backs over the edge of a dump point or stockpile. Devices to monitor the blind areas of mining equipment are needed to provide a warning to operators when a vehicle, person, or change in terrain is near the equipment. Method: A proximity warning system (PWS) based on the global positioning system (GPS) and peer-to-peer communication has been developed to prevent collisions between mining equipment, small vehicles, and stationary structures. Results: A final system was demonstrated using one off-highway haul truck, three smaller vehicles, and various stationary structures at a surface mining operation. The system successfully displayed the location of nearby vehicles and stationary structures and provided visual and audible warnings to the equipment operator when they were within a preset distance. Summary: Many surface mining operations already use GPS technology on their mobile equipment for tracking and dispatch. Our tests have shown that it is feasible to add proximity warning to these existing systems as a safety feature. Larger scale and long-term tests are needed to prove the technology adequately. Impact on Industry: A PWSs that incorporates a combination of technologies could significantly reduce accidents that involve collisions or driving over an edge at surface mining operations.

By F. L. Wideman

SPURRED by demands of a buoyant economy for mineral products, output from mines in the United States established a new record. Removal of waste material, necessary for the extraction of economic minerals, kept pace with mine production. Earth moving by these two activities exceeded 3 billion tons, an increase of 5 percent over that of 1963. Crude materials from which metal or nonmetal products were derived accounted for 75 percent of the total. The remainder, mostly worthless, was classified as waste. Changes in the minerals industry result from many causes. Technological trends and labor productivity are among several significant and interrelated indexes that assist in the analysis of the changes. Therefore, a. study of productivity is helpful in measuring technological growth in mining. Concepts of productivity tend to vary with the purpose for which the term is used; frequently, productivity is expressed in terms of units of output per unit of labor, such as tons of ore per man-hour or man-shift. Comparisons of levels of productivity for a group of products are usually made using composites of output. Data for all metal and nonmetal mines except gold, silver, mercury, platinum metals group, and sand and grave were used to compile the composite for determining productivity for 1960-64. Copper ore, iron ore, and phosphate rock are mined mainly by surface methods, but characteristics of the deposits and differences in processing the crude material affect production of the commodities. Therefore, productivity data for these selected segments of the minerals industry reflect the influence of physical conditions on the exploitation of them.

Jan 1, 1965

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By J. Whyatt

A package of bench design programs is being publicly released by the National Institute for Occupational Safety and Health (NIOSH). These programs are designed to provide a probabilistic estimate of the likelihood that various widths of catch bench will be retained. Program modules address the mechanisms of plane, plane step path, and wedge failure. Results are drawn from statistical and geostatistical descriptions of fracture characteristics and other input parameters, and reported as the statistical chance that a given width of catch bench will survive, that is, that a catch bench will remain wide enough to catch rolling and sliding material and prevent such material from posing hazards to miners operating below. The capabilities and application of this software are demonstrated through a case example. Comparing bench width estimates obtained using geologic data with actual widths is a key step in verifying that a program is appropriate for particular site conditions and that proper statistical descriptions of fracture parameters for that site have been developed. Such verification efforts improve confidence, and hence usefulness, of this method for designing future slope benches. Development and release of these programs appears particularly timely given recent progress in photoanalysis methods, which promise to greatly reduce the cost of collecting fracture data.

Jan 1, 2004