Search Documents

By L. J. E. Hofer

The Bureau of Mines determined rates of adsorption and desorption of methane as a function of particle size and temperature, using coals from the Pocahontas No.3 seam (lvb) from the Bishop mine of western Virginia, and the Pittsburgh seam (hvab) from the Pursglove No. 15 mine of northern West Virginia. For a given coal sample and temperature, the rate curves for adsorption and desorption are essentially the same when expressed on a fractional approach to equilibrium basis. The rates of adsorption and desorption increased eightfold as the particle size was decreased from 6-8 to 270-325 mesh per inch. The adsorption process appears to be diffusion controlled. Rate of sorption processes increased with increasing temperature; however, the amount adsorbed at equilibrium decreased.

Jan 1, 1966

By Merle Randall

Application of a new chemical spray in a mercury mine in which ore rich in native metal was causing salivation among the miners has given such favorable results that it is believed the process will be useful in other mines and perhaps in some plants where similar conditions exist. The process was originated by Merle Randall, professor of chemistry at the University of California. GENERAL PROBLEM The presence of native quicksilver in mines from which the metal is produced has long been a source of trouble and danger to the workers. Men have been sickened and some of them have been disabled by exposure to the vapors present (even in workings that were well-ventilated by ordinary standards) and to contact with dust, dirt, and moisture with which the finely divided quicksilver was mixed. Where the ore was rich and this exposure was considerable men were able to work only a few days or weeks; where the exposure was less they were weakened and subject to ailments often attributed to other causes.

Jan 1, 1942

By Keith L. Harris

Real gross national product3 (GNP) grew at a seasonally adjusted annual rate of 4.2% in the fourth quarter compared with a revised 4.3% rate in the third quarter, according to the most recent estimates released by the U.S. Department of Commerce (table 1). Expanding inventories, Government purchases of goods and services, residential fixed investment, and a narrowing of the trade deficit fueled the growth. Significantly reduced consumer demand led to the heavy inventory growth. Almost half of the buildup in inventories consisted of automobiles because consumers reduced purchases when Detroit ceased most incentive programs in late summer. Reduced consumer demand also affected imports, however, and the narrowing of the trade deficit resumed after widening in the third quarter. Nonresi- [ ] dential fixed investment also declined after a strong gain in the third quarter. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 2.9%, the same as that of 1986. However, on a fourth-quarter-to-fourth-quarter basis, the real growth reached 3.8%, the highest growth since 19M, and exceeded the Reagan Administration's estimate of 3.4%. Rising merchandise exports accounted for about one-third of the growth in GNP for all of 1987 and are expected to continue to grow as domestic manufactures benefit from the lower value of the dollar vis-a-vis other major trading country currencies. Consumer demand became a less important factor of economic growth, but employment continued to grow (table 2), and civilian unemployment declined by 0.9 percentage points (December to December) as the industrial sector geared up to increase exports. Inflation, as measured by the fixed-weighted GNP price index, remained low at 3.4%.

Jan 1, 1988

By William Eathorne

"INTRODUCTION Retsof mine, adjoining the village of Retsof, Livingston County, New York, is about 5 miles northwest of Geneseo and 55 miles (air-line distance) due east of Buffalo. It is a single-bed rock-salt mine having extensive horizontal workings as much as 2-1/2 miles long and 1 mile wide and has been in continuous operation since 1885. Retsof tine is the largest producing salt mine in North America and is reputed to be the largest active salt mine in the world.Retsof is one of three large salt mines operated by the International Salt Co., Scranton, Pa.; T. Forster Courthope is general manager of Retsof and also of the company's Detroit salt mine in Michigan and has held that position for 27 years. He is assisted by Stanley Martin, general superintendent; R. Goetz, Maintenance superintendent; and John Riordan, mine superin¬tendent. All are old-timers at Retsof and, according to Courthope, contri¬buted the ""lion's share in bringing the mine to its present standard of safety.ACKNOWLEDGEMENTThis circular was made possible by the generous cooperation of T. Forster Courthope and his assistants, Stanley Martin, R. Goetz, and John Riordan. The information and time generously given are gratefully acknowledged.GENERAL INFORMATIONThe rock salt as mined contains about 99 percent sodium chloride and requires only crushing and screening to prepare it for the market. With the exception of a large jaw crusher underground, all crushing is done in a mill building attached to the headframe of the main hoisting shaft (fig. 1).Five sizes of salt are produced, ranging from about 1/2 inch diameter down to minus seven mesh."

Sep 1, 1949

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 29,020 acres of the 43,165-acre Terry Badlands Wilderness Study Area (MT-024-684) in order to evaluate its mineral resources. Within this report, these 29,020 acres are referred to as the study area. Located in Custer and Prairie Counties, MT, the study area is about 2 miles northwest of Terry. The study area is underlain by essentially flat-lying units of the Fort Union Formation of Paleocene age with some Quaternary alluvial deposits in stream valleys. No mines or prospects were found in the study area. Bentonitic clays and lignite coal units were examined and sampled; however, no clay resources or coal reserves were identified. Estimates of coal resources will be reported by the U.S. Geological Survey in a joint U.S. Geological Survey-U.S. Bureau of Mines publication. Gravel along the Yellowstone River, a source of agate for private collectors, could also be used as sand and gravel aggregate although material on the south bank of the river is closer to population centers and road systems. Clinker found in the study area could be a source of road metal, but is not well situated in relationship to areas of use. No geothermal resources have been identified although water suitable for direct heat applications may underlie the study area. All the area is leased for oil and gas exploration.

Jan 1, 1985

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By R. F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Bureau of Mines has developed a general method for preparing solutions from a wide range of metal and mineral samples for chemical analysis. The development of the method from current knowledge of vessel material, pressure dissolution techniques, and the fluoride-boric acid reaction is given. The method uses 7 ml of a mixture of HC1-HNO3-HF acids in a ratio of 3.5:2:1.5 sealed in plastic bottles that act as pressure vessels when heated in a boiling water bath. A final volume of 100 ml is obtained by the addition of 93 ml of a 1. 5-pct H3BO3 solution to the bottles, which are reheated; precipitated fluorides as well as sample residue are dissolved by the fluoride-boric acid reaction. A copper slag and a steelmaking slag treated using this method were analyzed by atomic absorption spectroscopy yielding values for Si, Mg, Ca, AI, Fe, Mn, Na, As, Pb, Sb, and Zn very close to certified values with an average relative standard deviation of 2.13 pct. The low cost, reduction in preparation time, ease and safety of sample handling, conservation of reagents, and ability to dissolve volatile materials without loss make this method superior to traditional wet digestion techniques for many materials, and ideal for use with atomic absorption, and optical emission or X-ray emission spectroscopy.

Jan 1, 1980

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

By K. O. Bennington

Enthalpies of formation of three sodium titanates were determined by hydrofluoric acid solution calorimetry, The values obtained for formation from the elements at 298.15° K are -370.9±0.5 kcal/mole for Na2TiO3, -832.1±0.9 kcal/mole for Na2Ti307, and -1,510.9±1.7 kcal/mole for Na2Ti6013. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and from the component oxides for Na2Ti03 and Na2Ti307.

Jan 1, 1973

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By Leonard Obert

This report describes the development of a dynamic strain gage and a companion amplifier and recording camera -an apparatus designed to pick up and record the strain waves produced in rock by a nearby explosion. Also included in the report is a discussion of the relationships connecting the strain with the displacement, velocity, and acceleration for both plane and spherical waves. The proposed tests for which the strain gages were intended required making measurements in solid rock, a factor that necessitated the development of a gage that could be inserted and anchored in a small-diameter diamond-drill hole. The restriction on the diameter of the drill hole is required so that the presence of the hole in the medium will not influence the propagation of the strain wave. The gage should respond with fidelity to the frequencies present in a wave pulse generated by the nearby detonation of a small quantity of high-velocity explosive. Preliminary tests showed that this frequency range extends from 200 to 10,000 c.p.s. or greater. Also, the gage should be capable of measuring strains ranging from a few micro-inches per inch to several thousand micro-inches per inch. Other desirable design specifications included a low gage output impedance to permit the use of long cables, and a low gage cost, particularly in view of the fact that for the final design none of the gages can be recovered from the medium.

Jan 1, 1949

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By Steven M. Shope

An essential element of the Bureau of Mines electromagnetic location and communication system for trapped miners is a quantitative knowledge of the surface and above-surface electromagnetic fields created by an underground transmitter. The field solutions given in this report use approximations in which the displacement currents are negligible for low frequencies. The earth is represented by a homogeneous half-space model in which a dipole source is immersed. The vertical magnetic field equipotential contours at and above the surface are graphically mapped. The volumes of the regions bounded by these contours are directly related to the geometrical zones of signal detectability. Knowledge of the detectability zones will enable the proper search strategies to be developed for airborne detection of trapped miners.

Jan 1, 1983

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By T. J. Ballard

The Conrad Hill mine vas first opened as a gold mine about 182 and has been operated at various times since then. The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings. The work failed to reveal appreciable copper values or evidence of additional ore deposits.

Jan 1, 1948

By Hiram C. Draper

The Mining Division of the Bureau of Mines, in cooperation with the Obstacle and Demolition Branch, Engineer Research and Development Laboratories, Department of the Army, undertook some extensive tests to determine the effectiveness and limitations of using standard demolition-type shaped charges in underground Mining. The tests proved the shaped charge has no practical application in the functions of mining covered by this report. At an approximate cost of 0 per foot hole plus spall produced by the most efficient single shots with the M3 shaped charge, the cost is over 20 times that of producing a better hole with a rock drill. The concussion would prohibit its use in many mines, and the excess carbon monoxide gas liberated by the pontolite explosive would be an additional hazard when used underground.

Jan 1, 1948

By H. H. Schrenk

Much has been written and said concerning tables of permissible or maximum allowable concentrations of various toxic substances in air, but not enough attention has been given to their limitations and how to use them intelligently . There is a tendency to place too much reliance on figures , with little or no consideration of their real meaning . The repeated publication of a figure often adds significance to it far beyond that intended by the original author or publisher . How are these figures referred to as "maximum allowable concentrations " established? What is their real meaning? To answer these questions it is necessary first to define maximum allowable concentration . The usual definition is somewhat as follows : "The average concentration to which an industrial worker can be exposed for 8- hours daily for an indefinite period without injury or occupational disease . This definition is made up of the following items : ( 1 ) Average concentration, ( 2 ) 8 - hour day , ( 3 ) indefinite exposure period , and ( 4 ) lack of injury or occupational disease . There is some controversy regarding item ( 1 ) , items ( 2 ) and ( 3 ) are usually though not invariably accepted , and there is definite disagreement regarding the interpretation of item ( 4 ) . . To reach a more satisfactory interpretation of maximum allowable concentration , attention is directed to ( 1 ) the development of tables of maximum allowable concentrations , ( 2 ) criteria on which limits are based , and (3 ) methods used to obtain data on which limits are based .

May 1, 1948

By John J. Sammarco

This report (System Safety Guidance 5.1) is the sixth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various lifecycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 8, 2005