Search Documents

By J. A. McAllister

In the course of a study of domestic Manganese resources, 2-ton representative samples of ore were taken by Bureau of Mines' engineers from the Payday claim, Weber County, and the Newcomb-claims, Rich County, Utah. The Payday No. 1 deposit is situated 13 miles northeast of Huntsville, Weber County, Utah. The manganese ore is a. replacement deposit in limestone and consists of manganese oxides imbedded 'in clay and also as the cementing agent consolidating small pebbles and pieces of quartz and limestone.

Jan 1, 1949

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By L. B. Pankratz

High-temperature heat-content values of gallium and scandium sesquioxides were measured over the temperature range from 298° to 1,800° K. The results fill gaps in the thermodynamic information for these compounds; no previous similar data existed. The heat-content values were combined with heats and entropies of formation to obtain free energies of formation of gallium and scandium sesquioxides to 2,000° K. The thermodynamic stabilities of the sesquioxides of aluminum, gallium, scandim, and yttrium were compared.

Jan 1, 1963

By Leonard Obert

A triaxial procedure is described for measuring the modulus of elasticity and Possion's ratio of stress relief cores , that is , the concentric hole cores obtained by the overcoring technique . The elastic constant determinations can be made at stress levels comparable with those encountered in underground mining . The results from tests on an aluminum alloy calibration specimen and four rock specimens are included .

Jan 1, 1964

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By McHenry Mosier

The Anson Bette manganese mine, with two prominent manganese-bearing outcrops in schist, has attracted considerable attention for its variety of manganese minerals and its possibilities as a potential source of manganese. Little mining was done prior to 1925, when the present owner acquired the property, and operations since that date have been intermittent. Mine workings are open cuts with a maximum depth of 35 feet. The two outcropping ore deposits are irregular, pipelike bodies about 500 feet apart. As nothing was known of the grade or extent of mineralization in depth, four holes totaling 1,072.5 feet of bore Were diamond-drilled by the Bureau of Mines in the summer of 1943, with the results shown in figures 3 to 6. In.1945 a geophysical survey was run to map the magnetic anomalies in the manganese-bearing belt as a means of determining the locations of manganese deposits. Positive correlation of magnetite and manganese ore was not obtained.

Jan 1, 1949

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By J. R. Ruark

This report presents results of mining operations and of research and development work done during stage I of the gas combustion retorting research program conducted by the Colorado School of Mines Research Foundation and six major oil companies at the Bureau of Mines Anvil Points Oil Shale Facilities. A brief description of the gas combustion process is given and the experimental program is discussed. Included in this discussion are (1) air-gas distributor development, (2) results of gas and shale distribution studies, and (3) effects of other process variable studies. The report concludes with a statistical evaluation of experimental results. Two appendixes present a chronological account of the experimental work and tabulations of data for all retorting runs conducted during stage I.

Jan 1, 1969

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following questions are frequently asked by coal users: (a) Will the coal lose any, of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when coal is stored? DISCUSSION (a) Loss of Heating Value Studies by the Bureau of Mines show that the loss of heating value of coal in storage commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh gas, and Sheridan (Wyo.) coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating Value of Coal During Storage, by H. C. Porter and F. K. Ovitz (p. 8):

Jan 1, 1943

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By R. B. Schluter

The objective of this Bureau of Mines investigation was to determine the effects of adding manganese compounds and ores to iron ore pellets. Manganese dioxide, carbonate, sulfate and chloride, plus six manganiferous ores from the Minnesota Cuyuna Range were tested as additives to increase the manganese content of iron ore pellets. One to 5 percent manganese, as a compound or ore, was added to five magnetite concentrates and one hematite concentrate. These concentrates were ballad, indurated (1,300° C), and tested for reducibility. Manganese sulfate and chloride were unsatisfactory additives causing cracking and degradation of the pellets during reduction. Manganese dioxide, carbonate, and the ores were satisfactory additives. The additives increased pellet compression strengths with a corresponding loss of reducibility, as compared to the pellets without manganese additions. The changes in compression strengths and reducibility were caused by the formation of Jacobite spinel and slag within the pellets. However, when the induration temperature was lowered from 1,300° to 1,200° C the reducibility and compression strengths were comparable to the pellets without manganese additions indurated at 1,300° C.

Jan 1, 1974

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By D. L. Sawyer

Aqueous C12-02 leaching procedures developed by the Bureau of Mines to produce zinc chloride from zinc sulfide bulk concentrates were effective in extracting 99 pct of the zinc and 97 pet of the silver contained in samples of massive seafloor sulfides from the southern Juan de Fuca Ridge. Zinc sulfide (sphalerite and wurtzite) mineralization comprised 55 and 88 pct of two specimens provided by the U.S. Geological Survey for this study. Minor occurrences of galena, chalcopyrite, and other minerals in the sulfides permitted the recovery of pregnant liquors that were low in metal values other than zinc, which were successfully purified by a two-step cementation procedure using zinc dust.

Jan 1, 1983

By E. S. Shedd

The Bureau of Mines investigated electrowinning and tapping lanthanum metal from lanthanum oxide in a fluoride bath. The electrolyte was composed of LaF3, BaF2, and LiF. Metal containing 0.2 percent impurities was produced at a rate of over 2 pounds per hour. Principal impurities were carbon, aluminum, and silicon. Low-carbon metal was produced by continually discharging the carbon oxide gases and maintaining 0.1-atmosphere pressure. Anode reactions and cell design were found to be important factors in cell operation. Both frozen electrolyte skulls and tungsten metal crucibles proved satisfactory for collecting the metal and did not react with the molten lanthanum.

Jan 1, 1966

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By H. V. Makar

A study was conducted by the Bureau of Mines to determine problems associated with the use of ferrous fractions from urban refuse as melting stock for steelmaking and to evaluate the resulting steel products. The study involved 50-pound ingots from laboratory melts and 50-pound ingots from 1-ton electric-arc-furnace melts. The 50 pound ingots from the laboratory melts and the arc-furnace melts were hot rolled to provide material for mechanical and corrosion testing. Results obtained in the study include the following: Most steels rolled successfully and exhibited acceptable surface and edge condition. Tensile strengths of the plain carbon steels were not significantly affected by copper up to concentrations of 0.65 pct and were not affected by tin content up to 0.16 pct. Yield strength increased with increasing copper and tin contents, and impact strength decreased with increasing tin content. Hardness increased slightly with increasing copper content. In general, properties of the steel produced were not measurably affected by charge composition (that is, melting stock), melting practice, or method of scrap preparation.

Jan 1, 1975