Search Documents

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By E. P. Youngman

At the time of the preparation of the monograph upon the mining legisla- tion of Newfoundland, by the Imperial Institute of London, the existing local statutory law (as distinct from case laws and the applicable English acts) con- sisted of the following legislation: 1. Chapter 129 of the consolidated statutes, entitled "Of Crown Lands, Timber, Mines and Minerals," as amended by the Crown lands act, 1928. 2. Chapters 131 and 132 of the consolidated statutes (acts relating to mines regulation and rewards for discovery of minerals, respectively). 3. Crown lands act, 1918, as amended by the crown lands (amendment) act, 1921. 4. The Labrador Act, 1927. 5. The Crown royalties act, 1927. 6. Crown lands act, 1928, together with rules and regulations issued thereunder.

Oct 1, 1932

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

By R. L. Grayson, W. E. Wallace, T. Simonyi, J. C. Harrison

"Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz may have different amounts of surface-availablequartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface-available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.INTRODUCTIONFrom our previous work (Grayson, 1991), we have shown that the amount of pure quartz in a respirable coal mine dust sample appears to vary directly with the rank of the seam (using fixed carbon as the basis for comparison), except when a substantial rock parting, roof or floor are mined. Our other work (Wallace et al., 1989) showed that high-silica particles in a clay mine may generally be coated with clay, rendering the quartz core non-available for surface reaction in the lung. The combination of these findings led us to hypothesize that the coating phenomenon may indeed be present in coal mines as well, and that a rank relationship may be present regarding this phenomenon. Thus higher rank coal seams may have more surface-available quartz as well as more pure quartz particles in their respirable dusts. The scientific protocol for testing this hypothesis and the results obtained to date are discussed in this paper. Thus far, there is no reason to doubt that the relationship holds."

Mar 1, 1992

By R. E. Head

"The microscopic work described below was engaged in primarily into ascertain the approximate proportions in which the copper sulphides existed in the ore examined, and by a comparison of the results obtained from a study of both head are tailing samples to supply data which might be of value in treating the ore by flotation. Incidentally, the physical characteristics and association of the sulphides were noted in order to determine the possible relation or bearing of these features on the present conditions of treatment. Since the copper in the ore occurred as three distinct sulphide minerals - chalcopyrite, chalcocite, and bornite each containing copper in different proportions, there appeared to be little or no possibility of obtaining the desired information by chemical methods of determination.Type of material examinedThe material examined was in the crushed condition and was said to be representative of the flotation feed or heads and the resulting tailing. No hand samples of the ore were examined nor any account taken of the physical condition and association of the minerals in place, because the possible value of the analytical results depended on conditions as they existed in the crushed ore. As the problems under consideration dealt only with the sulphide minerals, especially those of copper, the products from screen sizing were concentrated by hand panning and the gangue discarded. The concentrate obtained consisted almost entirely of the sulphide minerals, since the panning had been very carefully done. The object of this procedure was to obtain a sufficient quantity of high-grade sulphide material, from the sample of each screen size selected for examination, to permit its being so prepared for examination as to be representative of the physical characteristics exhibited by a large number of sulphide grains from each respective size, In the tests and investigations carried on by the company' treating the ore the following sizes had been used in tabulating data and basing conclusions:+48, +65, +100, +150, +200, and -200. These same sizes were used in the microscopic investigation, since the results obtained thereby could be most readily utilized for comparison with the results obtained in previous experimental work, together with deductions based on actual concentration of the ore on a commercial scale."

Jun 1, 1921

By R. R. Wells

This report summarizes the results of laboratory testing of copper-bearing magnetite ore from the Poorman, Bush & Brown, and Copper Center deposits, Kasaan Peninsula, Prince of Wales Island, southeastern Alaska. The ores contain minor amounts of chalcopyrite and pyrite. Intimate association of these sulfides with magnetite necessitates fine grinding for adequate liberation and rejection of copper and sulfur and for the production of high-grade iron concentrate low in objectionable impurities. Laboratory tests indicated that the optimum results can be obtained by flotation of ore ground to minus-100-mesh, with subsequent wet magnetic separation treatment of the flotation tailing. A summary of results obtained by this treatment of the three samples tested is shown in table 1.

Jan 1, 1957

By N. S. Dalal, Xianglin Shi

"Electron spin resonance (ESR) spin trapping experiments have been carried out to investigate the mechanism of sulfite oxidation em¬ploying 5,5-dimethyl-l-pyrroline-1-oxide (DMPO) as a spin trap. The results show that sulfite autoxidation, catalyzed by Mn(II), involves not only the SO-3 radicals but also the •OH radicals. An addition of H2 02 to the sulfite aqueous medium significantly increases the •OH radical formation. This result provides new clues to the chemical mechanism of the sulfite oxidation and the sulfite toxicity.INTRODUCTIONStudies of the oxidation of the sulfite (SO 2-/3) ions under various conditions are of high current interest because excessive exposure to sulfite is toxic and the origin of this toxicity seems to involve sulfite oxidative pathways [1]. An important fact is that human exposure to sulfite is on the increase [1,2]. Some of the increase in the sulfite exposure is linked to the fact that SO2 is a major air pollutant [2] and in aqueous media SO2 exists in equilibrium with SO2-/3. In addition, beverages and foods are common sources of sulfite intake. For example, sulfite is used extensively in the wine industry as an inhibitor of yeasts and bacteria and is present in finished wines in concentrations up to 6 mM [1]. Sulfite is also often added to dehydrated fruits, vegetables and soups, as well as fruit juices and beer [1,3,4]. Because of these, the mean daily intake of sulfite from diet (in the United States) has been estimated to be between 0.0014 and 0.14 mM/kg body weight [1]. At such high levels, sulfite exposure can have toxic effects, such as the induction of an acute asthmatic state [5,6]. Sulfite also appears to have adverse genetic effects [7] and can act as a mutagen or comutagen [8] and a cocarcinogen [5,7-9]."

Jan 1, 1990

By R. V. Ramani, K. Bode

"IntroductionIn part 1 of this paper, the results of the experimental work in a wind tunnel under controlled conditions were presented. To understand the spatial and temporal behaviour of airborne dust under mine conditions, experiments were performed in the Lake Lynn Experimental Mine of the US Bureau of Mines. The mine airway experiments were designed to study the variations of ambient concentrations along the length of an airway, and the deposition rates and deposition velocities in an airway cross section. Other objectives of the study were to investigate the spatial and temporal behaviour of airborne dust with regard to air velocity and particle density, the size distribution of the airborne dust cloud as it travels in the airway, and the size distribution of the dust particles deposited along the airway. Other objectives of the study were to compare wind tunnel results with In-Mine results, whenever appropriate.Experimental ProcedureLocationA complete description of the Lake Lynn Laboratory Mine of the US Bureau of Mines (USBM) can be found in the US Bureau of Mines Information Circular 8911 (Mattes et al., 1983). This mine provides excellent facilities for dust experiments. The airway dimensions are similar to those of a coal mine airway. The mine has a drift (D Drift, see Figure 1) that extends almost 500 meters without interconnecting airways, stoppings, or bends. The D drift measures approximately 6m in width and 2,25m in height.The Lake Lynn Laboratory Mine· is ventilated by a variable speed, 75 kW (100 hp), 28,3 m3/s (60 000 cfm) blower fan installed on the top of the ventilation shaft. Air velocities of 1, 1,3 and 1,8 m/s, respectively, could be obtained in the D Drift. However, the temperature changes at the surface can cause small variations in air quantities and velocities underground. The low background dust level in the mine reduces the problem of sample contamination from other sources of dust. Extended periods of uninterrupted data collection can also be scheduled. Mine airway parameters which are important for the analysis include the dimensions of the airway and the ventilation data such as the air velocity, and the pressure loss in the drift. All these data were acquired during altimeter surveys which were conducted prior to each of the experiments."

Dec 1, 1995

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite having length to diameter ratios of 3:1, 2:1, 1:1, and 0.5:1 were broken in axial compression to determine whether lateral end constraint affected the breaking strength. Steel rings bonded to the ends of the model pillars with epoxy provided, during the loading cycle, a lateral end constraint of about 17 to 30 percent of the average axial stress. The effect of this constraint was to increase the breaking strength of the rock as compared to cylindrical pillars without constraint. The percentage increase in breaking strength varied with rock type and increased as the length to diameter ratio decreased. The maximum increase in breaking strength was 35 percent for marble pillars having a length to diameter ratio of 0.5:1. A theory was developed which relates the expected constraint to the physical properties of the ring and rock.

Jan 1, 1968

By J. B. Gayle

The rate of oxidation of coals with nitric acid has been used by earlier investigators4 5 6/ for determining fusain and for studying petrographic composition. These workers accumulated considerable evidence indicating that, for coals ranging from lignite to low-volatile in rank, the method gives values for fusain that agree satisfactorily with those obtained by optical methods. One group5/even concluded that, when discrepancies are noted between results obtained by chemical and microscopic methods, the results based on the oxidation reaction are probably the more reliable. Unfortunately, after concluding that the method was valid, most of these workers apparently lost interest. As a result, no attempt to exploit or apply the method to problems of utilization has been reported. Recent studies of the influence of inert petrographic constituents on the properties of cokes made from various coals7/ have indicated a need for additional means of characterizing coals and blends used for carbonization.

Jan 1, 1960

By Lars Osen

The Bureau of Mines investigated (1) the effect of torsion on yield and ultimate strengths of bolts when the torsion is applied first and tensile load is applied independently of torsion and (2) various methods of increasing the tension-torque ratio and/or narrowing the data spread of the tension-torque relationship. A special torsional attachment was fabricated to attach to a universal testing machine to independently subject rock bolts to combined tensile and torsional loads. It was found that initially installed torsion is nullified during tensile loading and the tensile yield and ultimate strengths are not significantly reduced. Lubricating various components of a bolt assembly or using hardened washers will improve the tension-torque relationship during conventional installation; however, the torsional load is not nullified during this type of loading. Hence, a bolt is subjected to a combined stress throughout the loading cycle; the yield point will thus be lowered compared with the pure tensile yield if care is not taken during installation to stay below the torsional yield.

Jan 1, 1966

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By Jon I. Voltz

The U.S. Bureau of Mines has conducted fundamental coal fragmentation studies to evaluate the effects of impact energy and direction of bedding planes on dust generation, size distribution, and impact-output energy relationships. Product size distributions were obtained for the fragmented samples by screening to minus 150 mesh. The minus lS0-mesh fines were analyzed with a light scattering photometer with a measurement range of 176 to 1.9 /.tm. Increased input energy produced a significant increase in the weight of plus 3/8-in material for impact perpendicular to the bedding planes. No significant trend was observed for parallel impact. Impact direction had little influence on dust size distribution, and input versus output energy relationships. As expected, total airborne dust measured at time of impact and percent particulates below 11 /.tm in size generally increased with increased input energy for both directions of impact. Energy used for sample fragmentation increased with increased energy input.

Jan 1, 1989

By Mary F. Koehler

Interoxidic compounds, such as vanadates, have not been studied extensively in the field of thermodynamics. This is a report of three vanadates of sodium--metavanadate, pyrovanadate, and orthovanadate. Vanadates of other metals will be considered in future reports. The heats of formation at 298.15° K. of the three sodium vanadates (both from the oxides and from the elements) were derived from the results of sodium hydroxide solution calorimetry. Free energies of formation were obtained by combining heat and entropy values. The results support the conclusion that the three sodium vanadates were stable with respect to all possible decompositions in which vanadium retains its pentavalency.

Jan 1, 1960

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By Richard C. Ballance

Fly ash from four sources and in certain proportions was shown to assist chemical coagulation of turbid water and settling of chemically induced floc. Fly ash reduced the time required to form the first visible floc, promoted more uniform flocs about 2 mm in diameter, and increased the mean settling rate of floc particles. Also, the addition of fly ash produced denser sludges than those obtained with alum alone. Final turbidities were independent of fly ash particle size and carbon content. Optimum proportions of fly ash additive are given.

Jan 1, 1966

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950