Search Documents

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The float-and-sink test 5/6/ is generally the first test used in determining the washing characteristics of coal. The simplest form of the test is that of using one solution of such specific gravity that the test sample is separated into ""float"" and ""sink"" fractions. In practice, however, a series of solutions is used, and the sample is separated into a number of fractions of a definite specific-gravity range. Analyses of a series of fractions of this type are often referred to as the ""specific-gravity analysis,"" and are of great value in the selection, construction, and operation of commercial washing equipment.The test is rather simple to use, provided a number of conditions are recognized and as many as possible held constant, such as:1. In laboratory testing, two types of solution are available -Aqueous solutions of calcium and zinc chlorides.Mixtures of organic liquids such as carbon tetrachloride, benzene, gasoline, bromoform, etc.2. Absorption of the solution by the coal,3. Solvent action of the solution toward the coal.4. Constancy of specific gravity during the test is affected by temperature changes, dilution, and evaporation.5. Personal technique of the test, such as the time the coal is in the liquid, rate of adding the sample to the liquid, stirring, time of draining, etc.6. Moisture content of the coal as tested."

Dec 1, 1947

By Tell Ertl, Ernest E. Burgh, John R. Wagner

The principal goal of the Oil-Shale Mining Division is to develop the most economical methods and practices for mining oil shale. Experimental work in the mine has not progressed far enough to conduct full-scale breaking tests; therefore, mining season - to October 31, 1945, has been confined largely to problems connected with drilling cost oil shale. Calculations have indicated that commercial production will result in breaking the oil shale; the largest individual turn will be for drilling. This paper is a report on the progress of phase two of drilling research to date; it outlines the development of a successful hard-surfaced rock bit for drilling oil shale.

Dec 1, 1948

By H. Dolezal

An investigation was made on the use of magnesium for the direct reduction of rutile to make low-cost, offgrade titanium which could be upgraded to an acceptable grade of metal by electrorefining. Reductions made with charges containing magnesium chloride under hydrogen yielded products with oxygen con-tests close to the theoretical equilibrium composition. Two reduction products were made from rutile for use in electrorefining amenability tests: (1) a product from reduction in an inert atmosphere which contained 88.9 percent titanium and 4.42 percent oxygen, and (2) a product from reduction in a hydro-gen atmosphere which contained 92.5 percent titanium and 2.40 percent oxygen. Reduction products obtained under both of these conditions were amenable to electrorefining.

Jan 1, 1965

By P. L. Woolf

An investigation was conducted to evaluate the use of a formcoke as the total fuel in the Bureau of Mines experimental blast furnace. The formcoke performed very satisfactorily, and comparisons made with a metallurgical coke showed that the performance with the formcoke was somewhat superior under the experimental conditions used.

Jan 1, 1966

By F. R. Cattoir, R. E. Cumings

Columbium metal was electrorefined in a fused - salt electrolyte . Excellent results were obtained in lowering the impurity content in a 94 - percent columbium anode feed material to produce a 99.8- percent - pure metal . The reductions of the major impurities follow : Oxygen from 19,800 to 500 ppm , carbon from 9,700 to 25 ppm , iron from 9,200 to 630 ppm , nitrogen from 2,100 to 90 ppm , and silicon from 750 ppm to not detected . Columbium with a purity of 99.9 percent was produced from 99.5- and 99.8 - percent grades of columbium. The investigation was devoted to the evaluation of a fused - fluoride - salt electrolyte ( KF - NaF- K₂ CbF, ) for electrorefining columbium. The effects of the columbium concentration and the voltage upon the product's purity were investigated . The effect on the cathode current efficiency of ampere - hours of deposition and the formation of a dual valence state of the columbium was also investigated .

Jan 1, 1964

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964

By W. W. Adams

"The National Safety Competition of 1930, the seventh annual contest conducted by the United States Bureau of Mines to promote safety in the mines and quarries of the United States, has been concluded, and the five winners of the bronze trophies, The Sentinels of Safety,' which are provided by the Explosives Engineer magazine and awarded annually for the most excellent safety records, have been determined by the committee of award. One trophy was awarded to an anthracite mine in Pennsylvania, one to a bituminous coal mine in the same State, one to an iron-ore mine in Michigan one to a gypsum mine in Ohio, and one to an iron-ore opencut mine in Michigan.These trophies were awarded to the companies for having the smallest loss of time from accidents in proportion to the total number of man-hours worked by all employees at their mine or quarry. Honorable mention was awarded to each mine or quarry that ranked second, third, fourth, or fifth in its own ground and to all plants that were operated without a lost-time accident during the contest year. Eighty-four out of 337 plants that competed for the trophies were operated without an accident that disabled an employee beyond the day on which the accident occurred.Under the contest rules, all mines and quarries were divided into five groups, four of the groups representing different classes of underground mining operations (anthracite, bituminous coal, metallic ore, and nonmetallic mineral), and the fifth group repre-senting the quarrying or opencut mining of minerals whether metallic or nonmetallic. Twenty-seven mines were included in the anthracite group, 68 in the bituminous group, 52 in the metal group, 24 in the nonmetallic-mine group, and 166 in the quarry and opencut-mine group. The total of 337 mines and quarries was 26 more than the number of plants that completed the contest during the previous year.The committee of award which determined the winners of the contest was composed of seven members, all known throughout the mineral industry but not connected with the United States Bureau of Mines. The committee included W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, Secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of Mining and Metallurgy; C. B. Huntress, executive secretary of the National Coal Association; A. J. Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association."

Jun 1, 1931

By W. D. Riley

The Bureau of Mines is conducting research on methods for the rapid identification and sorting of mixed scrap metals and alloys so that domestic scrap resources can be fully utilized. One method, spark testing, is the examination of the pattern of sparks that results when a metal or alloy is ground on an abrasive wheel. This technique requires experienced sorters. Bureau researchers have shown that spectrophotometric methods can be used in lieu of the highly skilled sorter. The spectra of a mild steel, an HSLA steel, several stainless steels, and four nickel-base alloys have been measured. Differences in the spectra that are sufficient for identification are apparent.

Jan 1, 1985

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By C. L. Brown

The frequency of mine fires during recent years, with an apparent increase in recent months, has focused attention on the necessity of reducing this hazard by every means possible. Investigation reports are available on 51 mine fires of electrical origin between August 15, 1949, and August 16, 1954. Nine other fires in the same period were suspected as being of electrical origin. Every mine fire is a potential hazard to underground workmen; it is remarkable that only six lives were lost as a result of these fires, since the injury list was very high. Modern mining methods, with increased power demands and extended distribution systems underground, involve greater electrical hazards and possibilities of costly production delays as a result of inadequate electrical service. Improvements in electric-power-distribution facilities in many underground coal mines is desirable. The purpose of this paper is to show the need for this improvement as revealed by studies and investigations of electric-power-distribution systems representative of those in a large number of coal mines.

Jan 1, 1955

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules3 include 13D for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer4 of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 130 for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and .mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the deice meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By R. P. Maloney

The Bureau of Mines conducted a reconnaissance of the less accessible parts of the Beluga River coalfield in August 1957 to determine, if possible, which areas were most favorable for developing large reserves of coal suitable for open-pit mining. Several outcrops of subbituminous coal were observed within an area about 30 miles long and 3 miles wide; neither the length nor the width of the coal-bearing area was delineated by the examination. Coal beds 30 feet thick or more outcrop at two places, and beds 5 to 20 feet thick or more outcrop fairly abundantly along the Beluga River and its tributaries The coal measures appear to occur in a series of folds. The overburden comprises glacial gravels and poorly cemented sandstones and ranges from 20 to 400 feet in depth. Few partings were seen in any of the coal beds. Samples ranged in calorific value from 6,240 to 8,246 B. t. u. on an as-received basis. Adequate water is available for stripping by hydraulic methods.

Jan 1, 1958

By J. A. Eisele

The Federal Bureau of Mines is engaged in a continuing program on the recovery of alumina from domestic source materials. Of the six processes being studied, current efforts focus on HCl leach of clays. A key step in the HCI process is the removal of iron from the aluminum chloride leach liquor. This was accomplished .by solvent extracting the iron with a tertiary amine in kerosine to which decanol was added as a phase modifier. In a mixer-settler operation, iron in the raffinate was reduced to <10 ppm in two extraction stages from a feed containing 1.4 gil Fe. Iron was stripped from the organic phase in three stages with dilute HCl.

Jan 1, 1976

By James R. Boyle

The value of Alabama&apos;s nonfuel mineral production in 1984 was $409.8 million, and established a new record high for value of nonfuel minerals in the State, at 13.4:% over the previous high of 1983. Output of nearly all nonfuel minerals increased; phosphate rock was one of the exceptions, with no recorded output in 1984. Cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in fire clay and kaolin; fourth in bentonite, ferroalloys, and dimension marble; fifth in masonry cement, lime, and recovered sulfur; and sixth in portland cement. Alabama ranked 22d in the Nation in value of nonfuel minerals produced.

Jan 1, 1986

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by The Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township-is given with the discussion covering that area.

Jan 1, 1948

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an exten- sion of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, how- ever, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's pro- duction facilities are maintaining a satisfactory quality control.

Oct 1, 1965