Search Documents

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in rescent years. The tenative ball-mill grindability method D408-35T4/ was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity.

Jan 1, 1938

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By G. L. Oldright

The first Report of Investigations of the present series (No. 4562) was on the fundamental properties of lead compounds, and the manner in which they set limits to the richness of lead products treated in the usual sintering-blast furnace units. These properties of the compounds were emphasized, as' it was desired, also, to learn the limitations of smelting the same compounds in present ore hearth practice; the hearth has a competitor in these "usual" units, even with the rich lead feeds best adapted for the hearths. Operating conditions that were followed in older metallurgical processes, when rich products, were treated, were outlined. The second report of the series (R. I. 4563) was on the development of the ore hearths of the types now used in the Tri-State from the viewpoint of the features, functions, and dimensions of the earlier hearths that had been most changed. Experimental data, for both well and poorly desulfurized charges being considered, were given to show the relative changes in the sizes and compositions of the charges after they were added to the ore (Scotch) hearths. A general picture was given of the charge column and of the conditions prevailing there when the operation was satisfactory. In this third paper, the composition of the gases prevailing in the charge column at various elevations will be correlated with what has been learned of the nature of the charge column in order to trace the steps of operation by which lead sulfide is converted into metallic lead. The metallurgical factors that govern operation and the lines along which improvements may be made will be noted.

Jan 1, 1949

By Y. Miron

'This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, g the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2).

Jan 1, 2010

This summary of State laws on explosives wag compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not Include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By Frank K. Cameron

"The DepositsThere are two large deposits or groups of deposits of potash salts which, at the breaking cut of the great world war in 1913 and for several decades preceding, were practically the only commercial sources of supply for the entire world. In both cases the origin of the deposits was sea water, the potassium salts being deposited by desiccation, but there were modifying factors which were not entirely the same in both cases so that well defined and important differences exist in these deposits. The larger and better known group, called the Stassfurt Deposits, are in Germany in the region about or adjacent to Magdeburg and Halberstadt. The general character of these deposits and the methods for recovering potash from them have been frequently described, not only in technical publi¬cations, but in the non-technical propaganda long maintained by the Kali Syndikat, an organization founded on a ""cartel"" with the supervision and support of the late Imperial German Government.Less well known are the smaller though nevertheless extensive deposits in the neighborhood of Mulhouse in Upper Alsatia, which were also under the control of the Kali Syndikat at the breaking out of the war but have now passed to French control, with the reentrance of Alsace into the French Republic.The Alsatiaa deposits, while less extensive than the German deposits, are, nevertheless of great magnitude. They occupy a large part of the area between the Vosges Mountains and the River Rhine, from Col¬mar on the North to Mulhouse on the South. Indeed a few borings on the East bank of the Rhine indicate that the deposits may extend under the river and to some distance beyond Buggingen Linken, Baden, though it has not been Shown as yet that this extension is of commercial significance.As is well known, the Stassfurt potash occurs as potassium chloride or potassium sulphate or both salts, intimately mixed with salts of sodium, magnesium eau& calcium (lime) and contaminated with substances. insoluble in water such as ferric oxide, clay etc. The potash salts are segregated in more or less extensive 'pockets' throughout the salt mass, these segregations departing usually from the horizontal. But the main ""potash region"" is a stratum varying from 30 to 150 feet in thickness and at a depth requiring shafts 5000 feet."

Jul 1, 1919

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

By G. B. Shea

Among the many engineering problems directly related to conservation in the petroleum industry, that of crude-oil emulsions continues to be important. Emulsions of water and oil always have constituted one of the most serious forms of waste in the oil fields, and the necessity of dehydrating emulsified crude petroleum to obtain marketable or pipe-line oil confronts operators in many fields with a major operating problem. In 1926 the Bureau of Mines published a comprehensive treatise s on oil-field emulsions dealing with field conditions, practical methods of dehydration, and physicochemical characteristics of the formation and resolution of emulsions. Although this bulletin is still available and may be obtained from the Superintendent of Documents, Washington, D. C., and although its contents are a valuable reference on the subject of emulsions, knowledge regarding the physical properties of emulsions and the phenomena of dehydration has increased greatly within the last decade. With the information gained through continued scientific research, substantial improvements have been made in the art of resolving petroleum emulsions. Moreover, in recent years there has been a growing realization of the importance of emulsion-preventive measures that has led to more critical examination of the causes of emulsions and methods of eliminating or at least reducing the degree of emulsification. Conditions causing agitation and commingling of oil and water and the formation of "cut oil" often are within the control of the producer, thereby making it possible to utilize preventive or remedial measures by which emulsification may be minimized or avoided. In fact, many companies have materially reduced their treating costs as a result of careful studies in emulsion prevention and proper handling of "wet" production. Of course, in many instances preventive measures or the correction of conditions causing emulsification cannot be achieved practically or economically, and the emulsions that form must be treated regardless of the care exercised or the money spent in attempting to prevent their formation.

Jan 1, 1939

By George K. Clement

Manual estimating method through use of equations, factors and curves for preparation of feasibility type estimates for capital and operating cost of mining and primary beneficiation in the United States and Canada of various types of minerals occurrences, except fossil fuels, using state-of-the-art technology. User should have basic estimating experience in the mining industry and/or related fields. Primary usage of this handbook will be for the preparation of preliminary estimate within a reasonable degree of accuracy with relative small amounts of hard input data. Output may be used to determine if a more finite type of estimate should be produced.

Jan 1, 1978

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

By C. L. Karr

U.S. Bureau of Mines (USBM) research has shown that fuzzy logic and genetic algorithms (GA's) have great potential for industrial process control. A technique has been developed by the USBM in which GA's are used to substantially reduce the time needed to design fuzzy logic controllers (FLC's).This technique shows promise as an efficient, robust approach to developing control systems. The research described in this report is twofold. First, the basic approach to developing an FLC using GA's is presented. The GA-designed FLC is developed for a specific physical system, a pH titration system. Second, empirical results are presented in which variations in the FLC implementation are compared. Specifically, the effects of altering five aspects of the pH FLC are considered: (1) membership function form, (2) number of fuzzy classes, (3) the center-of-area method, (4) implication operator, and (5) fuzzy rule form. Results indicate that (1) the technique in which GA's are used to design FLC's is effective, and (2) when this technique is used, variations in FLC implementation have little effect on FLC performance in a chosen control problem.

Jan 1, 2010

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010