Search Documents

By E. D. Gardner

Oil shale, a long-considered potential source of motor fuel in the United States, is found over an extensive area in the Green River formation in Colorado, Utah, and Wyoming.4/ Oil has been retorted commercially from shale in Scotland for many years,5/ and work done by the Bureau of Mines and other investigators has shown that it is technically feasible to extract oil from American shales.6/ By refining, the shale oil may be converted into marketable products similar to those manufactured from crude petroleum. The present paper, which was finished in 1936, discusses methods that would be adaptable to mining certain American shales, and the treatment applies specifically to conditions iii the Green River formation on Naval

Jan 1, 1942

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user's physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

By R. M. Santmyers

The chief compounds of boron are borax and boric acid, both of which have important applications in industry. At present the United States furnishes more than half of the world's requirements of borate materials, practically all from California. Nearly the entire production of borax in this country is under the control of four companies: The American Potash and Chemical Corporation, the Pacific Coast Borax Co., the West End Chemical Co., and the Western Borax Co.

Jan 1, 1931

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were undertaken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 2010

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By Larry A. Haas

The Bureau of Mines is investigating the use of complex gas mixtures, such as would be produced by coal gasification, for reducing iron oxide pellets. A semiempirical model was developed to predict a priori the reduction rate of an iron oxide pellet in a laboratory tube furnace with simulated coal gases at a total pressure of 1 atm. The model uses partial pressures of H2, CO, CO2, CH4 (methane), water vapor, and a temperature-dependent term to predict the rate of reaction. The reduction rate (weight loss per unit of time) was determined with a thermo-gravimetric apparatus (TGA) in the temperature range of 800° to 1,100° C. The ranking of the reductants, in order of decreasing reducing potential, is H2, CO, and CH4 at temperatures between 800° and 1,000° C; however, CH4 became a better reductant than CO at 1,100° C. Water vapor did not decrease the reduction rate as much as did CO2, Carbon deposition was observed at temperatures below 1,000° C with gas mixtures with high CO and low H2 concentrations. With low-Btu gas at 900° C, over 90 pct of the iron oxide was reduced to iron in less than 3 h. This com-pares with a reduction time of 1.5 h with medium-Btu gas and 1 h with reformed natural gases.

Jan 1, 1985

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By C. Steve Albrecht

The primary objective of this study is to "evaluate the influences of different equipment systems on prime farmland subsoil compaction due to surface mining in the Midwest." The study is centered on four mine sites each utilizing a different combination of equipment for soil removal and replacement. Subsoil compaction is the primary focus of this research effort. Primarily owing to physical location, it is difficult to alleviate the increased compaction directly below the topsoil in reclaimed soils. Different equipment combinations cause varied effects when soils are replaced during surface mining activities. By collecting field data within a statistical framework, the effects of different equipment combinations on subsoil compaction can be evaluated and conclusions drawn. This research effort evaluates a comparison of natural and replaced soils by moist bulk density data. This comparison centers on changes in bulk density and texture to a depth of 48 inches. For each study site a complete case study is provided for use in data correlation and interpretation. Basis for this research effort centers on four (4) major experiment designs: o Comparison of soil bulk density values for three distinct equipment systems evaluated on the same general soil types (i.e. scrapers, bucket-wheel excavators and end-dump haulback); o Evaluation of the effects of soil replacement in repeated lifts using scrapers; o Presentation of bulk density values representing soil compaction for four (4) equipment systems (i.e. bucket-wheel excavators, draglines, scrapers and end-dump haul back) on four separate mine sites in the midwest; o A prediction analysis model is developed for subsoil bulk density following reclamation based on equipment characteristics and a statistical evaluation of texture. The soil data base of information includes data from the 1982 Bureau of Mines study entitled, "Impact of Surface Mining on Soil Compaction in the Midwest" as well as data from this research project. The final report is synthesized through an analysis of field data, statistical analysis and literature review. The final report focuses on the interpretation of results for practical application by government and industry.

Jan 1, 1984

By Allan E. Martin, George Glocker, C. E. Wood

"INTRODUCTION As part of a comprehensive investigation of the mechanism of defurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope.Vogt/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FexCay)S and (MnxCaa)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.Coloration of glass by sulfur also provides indirect information on the nature of sulfur in blast-furnace slags./ There seems to be a general agreement at present among the workers in the field of colored glasses that ferrous sulfide is a strong color producer. Colors that have been attributed to this compound include yellow, orange, brown, blue, and black. Apparently the ferrous sulfide is considered to be dissolved in these glasses. There is no indication that any of them have been examined for a colloidal phase.Lorenz 7/ investigated a single manganese slag in the glassy state and observed a Tyndall beam in an ultramicroscope. His conclusion was that either a manganese compound had precipitated in a finely divided condition or that metallic manganese had volatilized and penetrated into the slag as a vapor and thus formed colloidal particles."

Feb 1, 1941

By F. D. Sutterfield

This study was conducted to provide experimental evidence on the effect of modifications of gasoline front-end composition on the photochemical specific reactivities of automotive emissions. Evaporative and evaporative-plus-exhaust emissions from an automobile operated with four fuels of different volatility and varying levels of C.-C5 olefins were irradiated in a 10040 environmental chamber at three sets of initial hydrocarbon-nitrogen oxides concentrations. Reactivity was measured and expressed in terms of rate-of-NO2 formation and dosages of oxidant, peroxyacetyl nitrate, and formaldehyde. The compositional changes that were necessary in reducing fuel volatility were found to have no significant effect on the reactivity of the emissions. However, replacing C4-C5 olefins with saturated components resulted in sharp decreases in all reactivity manifestations observed for the evaporative emission samples. A lesser influence (of C4-C5 olefin replacement) was found with the composite exhaust-plus-evaporative samples; the effect that was observed could be attributed to the evaporative emission portion of the sample. The data therefore suggest that saturation of front-end fuel olefins had no large effect on exhaust emission reactivity.

Jan 1, 1971

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By N. N. Moelbs

The U.S. Bureau of Mines is conducting research on many topics relating to the hazards of coal mining, increased production, and protection of the environment. One area of research that has received scant attention in recent years is that of water inflows, probably because few fatalities in the United States have been attributed to them. As mining goes deeper, the problem of water in 1ow could increase dramatically because of adjacent or overlying mines in which huge water pools are impounded. Inaccurate mine maps and ineffective barriers can constitute a serious problem for operators both from gradual inflows and sudden inrushes of water. This report describes a wide but ineffective barrier that permitted an average 240-gpm inflow to a developing mine from an adjacent mine. The anomalous geologic structure that facilitated this leakage is described, demonstrating that size, alone, is no assurance against serious leakage. Some recommendations for managing serious water inflow are included.

Jan 1, 1989

By Benjamin W. Haynes

Analytical procedures are described for the quantitative determination of 16 elements (As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn) and 7 ionic species (NH4, C032-, CI-, F-, NO3-, P043-, SO42-), identification of major and minor mineral components, and measurement of physical properties associated with manganese nodules and nodule processing reject waste materials. Compound identification methods discussed include X-ray diffraction, infrared spectroscopy, scanning and transmission electron microscopy, selective area electron diffraction, and optical and reflected light microscopy. Methods for elemental analysis include atomic absorption spectrophotometry, inductively coupled plasma emission spectroscopy, neutron activation analysis, fluorescent X-ray spectrography, and ion chromatography. Thermal gravimetric analysis, ultraviolet-visible spectrophotometry, ion specific electrodes, and standard wet chemical procedures are briefly discussed. Physical properties determined in manganese nodule materials include grain size distribution, specific gravity, triaxial shear, permeability, maximum density, Atterberg limits, and slurry density. The results of a round-robin analysis of an ammonia process waste material and manganese nodule standards demonstrate the applicability of the discussed methods. Tests discussed for the evaluation of the waste materials for disposal options include the Environmental Protection Agency (EPA) EP toxicity test, the ASTM shake extraction test, and the U.S. Army Corps of Engineers EPA seawater elutriant test.

Jan 1, 1983

By Noel N. Moebs

The Bureau of Mines studied the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian region. All relevant published literature pertaining to the occurrence and control of surface and ground water in underground coal mines was reviewed, and the impacts of mine water with respect to health and safety, production, environment, and costs were assessed and are described in this report. The report also identifies the sources of water inflow into underground coal mines, and gives a summary description and evaluation of techniques that can be used to reduce the amount of water entering these mines. Engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings were reviewed and are summarized. Major emphasis has been placed on the identification of geologic and hydrologic conditions of the site, the water control methods used, and an evaluation of their technical and cost effectiveness.

Jan 1, 1985

By C. Thomas Hillman

This Bureau of Mines report describes an investigation of factors influencing economic viability of a proposed system to mine and process manganese nodules. The system consists of hydraulic dredging and ammonia leach processing designed to recover three metals: nickel, copper, and cobalt. A ferromanganese recovery plant is a considered option. Annual capacity is 3 million dry metric tons (t) nodules. Aftertax rates of return (ROR's) of only 7.38 and 6.63 pct are predicted for three-and four-metal base scenarios, respectively. Sensitivity analyses indicate that variations in commodity prices, metal recoveries, and deposit grades produce similar incremental changes in ROR. Estimated cumulative effects of price variations are greatest. While three-metal operations generally yield higher predicted returns, potential increases in manganese price and process recovery could make four-metal operations most profitable. Maximum variations in both capital costs and three-metal operating costs result in ROR changes of about 25 pct. In contrast, four-metal ROR's exhibit variations to 70 pct. Even so only a best case analysis, utilizing favorable variations in all categories tested, generated ROR's approaching a level thought necessary to trigger company interest. Consequently, it is concluded that nodule mining will not take place in the foreseeable future without significant financial incentives.

Jan 1, 1985

By McHenry Mosier

This paper describing mining practice at Morenci, Ariz., is one of a series of articles on mining method, and practice in the various mining districts in the United States. At present (1929) practically all the mineral production in the Morenci district is from the Humboldt mine of the Morenci Branch, Phelps Dodge Corporation. The mining method used is adapted to the type of ore body being exploited; it has been developed by adopting methods used elsewhere and making necessary changes to fit local conditions. Improvements in current practices are still being made.

Jan 1, 1929

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By J. H. East, R. S. Sanford, W. M. Traver, W. S. Wright

"INTRODUCTION This report describes the results obtained from a diamond-drill exploration project performed by the Bureau of Mines on the nickel deposits of the Yakobi Island, Alaska. The Federal Geological Survey 6/ completed a detailed geologic study and mapped the area during the summer of 1940, and a Bureau of Mines examining engineer 7/ made a preliminary examination of the deposits in June 1941, at which time core drilling was suggested as the logical means of determining the extent and grade of the deposits. Equipment and supplies were unloaded on the beach at Yakobi Island on October 21, 1941. The drills were moved to Bohemia Basin, where actual drilling operations wore begun under the direction of a Bureau of Mines engineer 8/ on November 7, 1941. Two core-drill holes were completed on December 7, 1941. Upon the request of the drilling contractor, operations were recessed owing to severe winter conditions. Work on the project was resumed April 27, 1942, under the direction of another Bureau of Mines engineer 9/ and was completed August 15, 1942. During the 1942 season, 13 core-drill holes were completed, and 10 surface pits and a tunnel were sampled. A total of 5, 191 feet of core-drill hole was drilled in 15 holes during the entire project. The results of drilling and sampling form the basis of this report."

Jan 1, 1948

By Michael Radnor

The purpose of the study was to 1) examine the social and economic impacts of surface mine blasting in relation to variations in conditions of terrain and geology, population density and type, levels of ground motion and air blast; 2) consider technical, legal and government policy issues; and 3) examine the potential, nature and extent of surface mine blasting impacts and its regulations upon both communities and surface mining companies. Phase One designed the empirical research and technical analyses of Phase Two, focused upon surface coal mining and quarrying in the Eastern U.S. Several broad conclusions are evident: 1) blasting is not the major issue for communities or surface mine companies; 2) while the number of instances of severe cracking or annoyance are relatively small, the impact can be severe for individuals immediately involved; 3) blasting/drilling cost curves tend to rise significantly at intervals below 1.0 particle velocity, in/sec, dependent upon the size of a permit area and the size of a mine; and 4) the legal, complaint, cost and density analyses do not suggest the need for a general lowering of present regulations.

Jan 1, 1981