Search Documents

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By Charles Will Wright

This paper has been written to aid the owner of a small gold mine or prospect in preparing a report on his property for the purpose of interesting capital. If an owner can afford to do so, he should employ a mining engineer of recognized standing and experience to examine and report on his property, but many owners of small -mines and particularly of prospects cannot make the expenditure required for this. Further, many of them do not know how to prepare a description which will cover those features of a deposit on which a potential investor promises his opinion as to its worth. If such an owner is convinced that he possesses an orebody of sufficient grade and size to warrant the required expenditure for a thorough investigation and wishes to present his property to prospective investors, then the following suggestions concerning the proper way to sample his deposit, estimate the tonnage of developed and probable ore, and prepare a report may be of assistance.

Jan 1, 1933

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

Objective The main purpose of this video is to teach mine rescue personnel certain aspects of rescue work that are not traditionally taught. These include the strain caused by working continually under adverse conditions; the "survivor guilt" that occurs from being spared the fate of one's deceased cohorts; and the posttraumatic stress that may be experienced during the sometimes lengthy task of recovering the victims' bodies. Background On November 20, 1968, an explosion rocked the Farmington No. 9 Mine in northern West Virginia (figure 1). The explosion killed 78 of 99 miners who were working in the mine, including all but one member of the mine's rescue team. Some 30 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory (PRL) conducted a video interview with Danny Kuhn (figure 2), the only Farmington No. 9 mine rescue team member who was not working that day and who did not die in the explosion. According to the Mine Safety and Health Administration (MSHA), there are about 80 underground coal mine rescue teams in the United States, and according to the National Mining Association, there are more than 850 underground coal mines. This represents a significant decrease in both over the past decade. The low number of rescue teams is a concern because serious incidents, though fewer, still happen, and if a disaster occurs, there will be fewer rescue teams to respond. This would result in an increased need to use available human resources very efficiently. Much training to prepare these rescue teams still takes the form of what educators call "teaching to the test." In other words, teams practice in order to win mine rescue contests. This test-oriented approach has traditionally been augmented by interactions with others who have responded to real situations or by participating in actual incidents. Given few incidents and fewer rescue teams from whom to derive enrichment, the preparation of coal mine rescue personnel becomes a problem. Recently, more emphasis has been placed on active learning, such as working out problems in smoke. These sessions more nearly simulate the actual conditions that today's team members might rarely encounter. To properly prepare and retain the current coal mine rescue personnel who are left in the workforce, it is necessary not only to offer such hands-on experience, but also to replace the learning narratives that once were passed from team to team. The present video is intended to contribute in that capacity. Approach NIOSH researchers first learned of Mr. Kuhn in the fall of1998. Mr. Kuhn was contacted and agreed to an interview. An oral history interview was conducted with Mr. Kuhn in early November1998. After reviewing the videotape of the interview, researchers determined the content to be so rich as to warrant a second interview in a more formal setting. The second interview was done in early December 1998. During this interview, Mr. Kuhn spent about 2 hours describing the Farmington disaster, including the workplace climate leading up to the explosion, the events that took place in the 10 days after the explosion, and the nearly 10-year effort to safely and successfully recover most of the victims' bodies. The videotape of the second oral history interview with Danny Kuhn was reviewed and edited by NIOSH researchers for content. Careful attention was used to ensure that valuable information was presented, but within a reasonable timeframe. A detailed map of the Farmington No. 9 Mine was edited into the final video and used to highlight critical features as they were being described by Mr. Kuhn. Results and Accomplishments A 60-minute videotape and instructor's guide for use in safety training or other settings was completed. The target audience consists of all those who work in underground coal mines. This training video will help safety instructors better prepare mine rescue team members for the situations that they will encounter when engaging in extended rescue and recovery work. As a result of this expectations training, team members will be more likely to serve their

Mar 1, 2002

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 1927 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein.

Jan 1, 1935

A computer program for the static load analysis of linear elastic structures is presented. It is the product of a two-year project for the development of a efficient program for the analysis of mine-type structures. The report is divided into two parts. The first part explains the general method of analysis, the computer program organization and the most significant numerical techniques used. The second part is a user manual for the computer program. The FORTRAN IV computer program deck and example problems were transmitted separately to the sponsor. Request for a copy of the program should be directed to the Bureau of Mines, Denver Mining Research Center.

Jan 1, 1972

By Mark R. Pettitt

The charter of this investigation was to identify and promote the application of noise control technology to future longwall mining machinery. Intensive noise and vibration data were acquired on a typical longwall shearing machine, and the highest noise levels were shown to radiate from the cutter drums. Shearing machine cutter drum noise control techniques that take advantage of the nature of the dynamic forces generated during coal cutting were developed. These include both structural redesign and force isolation techniques. A reduced noise cutter drum was developed that achieved a 5 to 6 dBA system noise reduction at the operator's position. Its operational performance was verified by a six-month long in-mine test. It was evident from the data that additional noise reduction could be achieved by treatment of the shearing machine hydraulics. Noise control of secondary sources was also investigated. A method of reducing full or empty stage conveyor noise (and continuous miner conveyor noise) by 5 to 10 dBA was demonstrated through isolation techniques. Underground mine durability testing, however, is yet to be demonstrated.

Jan 1, 1986

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By Chas. F. Jackson

During the past year a special study was made of shrinkage stoping A large number of mines in the United States and Canada which employ this method were visited and their practices were discussed with the operating staffs. The operating data obtained are appended hereto. Data were also abstracted from the literature on other mines and are combined in tables with data personally secured by the author. References are made to these published articles, some of which have appeared as information circulars of the United States Bureau of Mines, in the Transactions of the American Institute of Mining and Metallurgical Engineers, and the Engineering and Mining Journal. Several of the mines referred to which have not been described in individual papers will be described in detail in information circulars to be issued by the bureau. Eventually it is planned to combine and condense the information in these circulars and present the data in bulletin form.

Jan 1, 1930

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By B. W. Madsen

A modified transpiration apparatus was devised by the Bureau of Mines to permit rapid and accurate measure of the vapor transport and vapor diffusion coefficients of antimony sulfide (Sb2S3) and other compounds at temperatures to 1,045 K. The apparatus was equipped with dual condensers and valves to switch the flow of vapor in a fraction of a second from one condenser to the other, thus allowing short-interval sampling under equilibrium conditions. Reliability of the technique was established by measuring the vapor pressure of ZnC12 as a function of temperature and comparing the results with published data. As part of an investigation of the vapor concentrations and species of accessory element sulfides associated with copper and zinc smelting, the apparatus was used to measure the rate of vapor transport and diffusion coefficients of vapor over liquid Sb2S3 as a function of temperature between 870 and 1,045 K. The calculated vapor density was combined with published direct measurements of vapor pressure to calculate the average molecular weight of the gaseous species. Average molecular weight of the vapor in equilibrium with Sb2S3 ranged from 286 to 112 g/mol over the temperature range studied.

Jan 1, 1983

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1976

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

These inspection standard have been prepared for use in the Federal inspection of strip mines producing, bituminous coal, anthracite, and lignite. This circular is a revision of the Safety Code for Strip Mining, which was prepared by the Bureau of Mines and employed as a guide for Federal inspectors. Numerous changes have been made in the original code to keep the in step with improvements in the industry. With continuing changes in mining methods and facilities some of these standards may become inapplicable and further revision may be advisable. Therefore, questions regarding these standards, and suggestions regarding new standards should be brought to the attention of the Bureau of Mines. Few States haves laws pertaining to strip mines, but where such laws do exist it is possible that some of the standards may conflict with them. In cases of conflict, the intent is not to advocate noncompliance with State laws, but to suggest reconsideration of such laws or safety orders.

Jan 1, 1946

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939