Search Documents

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

By R. V. Higgins

This paper describes a method and a computer program for calculating shape factors and areas of channels that turn more than 90° and conduct fluids into the backs of wells. The program represents an improvement over a previous Bureau of Mines investigation by using a 4-point Lagrange interpolation equation instead of a 3-point and by summing areas of trapezoids with either x altitudes or y altitudes. Some of the techniques reported in this paper can also be used to compute the areas between contours and the lengths of lines that turn more than 90°.

Jan 1, 1968

By David K. Denton

Results of the mineral resource study of the Upper Priest Lake RARE II study area indicate a low potential for the discovery and economic recovery of silver and lead in the Prichard Formation near contacts with the Kaniksu Batholith in the vicinity of the Mountain Chief Mine (fig. 1). Silver and lead minerals locally occur disseminated and in irregular quartz fissure-fillings in the Prichard Formation. Between 18^6 and 1967, 105 lode raining claims were located in the study area. The area was designated for "further planning" in the Final Environmental statement but was later changed to "nonwilderness" by President Carter after work was scheduled for the area.

Jan 1, 1981

By Robert M. Becker

This report (part 3 of a five-part series) presents computer programs for evaluating moments and moment relationships of the generalized probability distributions extended or developed in parts I and 2. The principal program is for evaluating the first three moments and moment relationships of the compound-multinomial distribution for finite as well as for infinite populations. This is the generalized distribution for sampling to some amount of items per sample. Another program is for evaluating the first four moments, the moments of the mean, and the moment relationships of the multinomial and generalized hypergeometric distributions. This is a general moment program in sampling to some number of items per sample or for sampling to some number of samples. This program will accept either ungrouped data, frequency data, or probability data.

Jan 1, 1965

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

By Dennis J. Grigal

The goal of the program is to develop a dust collector system mounted on a ranging drum or arm shearer which will: 1) reduce the respirable dust level of the shearer operator by at least 75 percent; 2) be easily and economically mounted on an existing shearer; and 3) will not, through modifications to the shearer, reduce its safety or productive capability. The development program consists of three phases covering the activities of the design of the dust collector system, fabricating and installing it on the ranging arm or drum shearer, and conducting underground field tests on the modified mining machine.

Jan 1, 1980

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

By Richard S. Gaps

In 1983 the U.S. Bureau of Mines conducted a mineral survey of the Golden Valley Wilderness Study Area (WSA), CDCA-170. The 29,887 acre WSA, located in the western Mojave Desert near Ridgecrest, California, is underlain by pre-Tertiary plutonic rocks and volcanic and sedimentary rocks ranging in age from Miocene (?) or Lower Pliocene (?) through Pleistocene and Recent. No mines were operating in the WSA in 1983, nor is any mineral production known to have come from the WSA. Two mining claim blocks, portions of which are within the WSA, and seven isolated prospects, four inside the USA, were examined and sampled. No mineral resources were identified. Widespread propylitic alteration, with localized argillic and alunitic alteration, occurs along the southern boundary of the study area. Samples from claims and prospects within the altered zones are anomalous in gold, silver and arsenic, and some contain antimony, tungsten and mercury, indicating gold resources may exist. Alluvial sample results suggest recent claims in the northwest corner of the study area may also have gold resources. Portions of the study area are within the Randsburg Known Geothermal Resource Area while other segments are considered prospectively valuable for oil and gas and for sodium.

Jan 1, 1985

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By T. W. Quayle

This paper describing mining practices at the United Verde copper mine, Jerome, Ariz., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts f the United States. At present mining operations are being conducted both underground and by electric shovels in an open pit. The open-pit work has been described by E. M. J. Alenius in a previous publication of the Bureau of Minos;3 the present paper will be confined to a description of the underground mine. The underground methods comprise horizontal cut-and-fill, shrinkage with delayed filling, horizontal square-set, inclined square-set, and top slice. The normal daily production of the underground mine is 3,000 tons of copper ore per day, requiring the employment of 900 men underground.

Jan 1, 1931

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932

By John Nagy

To facilitate increase in the rate of coal production the Bureau of Mines conducted a study several years ago, on the basis of which the allowable charge limit for permissible explosives in single-hole blasting was raised from 1.5 to 3.0 pounds. Further demands for accelerated production led to consideration of multiple blasting in coal, a practice that is deemed hazardous and is not permitted by most States in this country. In multiple blasting, 10 to 20 pounds of explosive or more may be detonated in a coal face within a fraction of a second, which might result in blown-out or blown-through shots with possible ignition of gas or coal dust. As experimental evidence was lacking, in January 1949 an investigation was undertaken in the Experimental coal mine at Bruceton, Pa., principally to study and compare with single blasting the condi-tions under which simultaneous multiple blasting and particularly multiple short-delay blasting may be practiced without danger of igniting gas or coal dust in mines. The first report on this subject was presented at the last international conference of mine safety research. Since that time numerous additional experiments have been made; because of other pressing problems the work has been brought temporarily at least to a conclusion. This paper is the second report on the problem. It does not contain a detailed description of all test conditions and test arrangements, many of which were described 2 years ago in part 1 (now available as Report of Investigations 4868), but the conclusions are based on the entire study. A more complete review, which will incorporate data from the entire investigation, is being prepared as a Bureau of Mines bulletin. Up to the present time, short-delay blasting of coal in commercial mines has been introduced only experimentally in Washington and in a few mines elsewhere. If the system is adopted more generally, new problems may arise, and the study may have to be reopened.

Jan 1, 1952

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By Wilford S. Wright, Harold E. Heide, Robert S. Sanford

"INTRODUCTION The United States production of tin has always been negligible, and domestic requirements have been met almost entirely by imports. The advent of war in Europe in 1939 brought a threat to our foreign source of supply, and steps were taken by Congress to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, the Bureau of Mines and Geological Survey conducted investigations of domestic tin deposits.An examination of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.H. B. Heide conducted a preliminary examination of lode and placer-tin deposits at Cape Mountain in 1942, which was followed in 1943 and 1944 by a program of exploration by churn drilling in the placer area and trenching and sampling the lode deposits.Placer tin, found at the head of Goodwin Gulch, Cape Creek, First Chance Creek, and Boulder Creek, indicates that the mineral was derived from the vicinity of lode cassiterite occurrences on Cape Mountain. Placer tin led to the discovery of at least one, cassiterite vein by the Geological Survey and the Bureau of Mines."

Dec 1, 1946

By B. K. Shibler, K. C. Vincent, W. W. Agey

"INTRODUCTION As a part of the investigation of domestic manganese deposits, examining engineers of the Bureau of Mines collected samples of ore from three from three properties in the general vicinity of Tracy, Calif.The Buckeye mine is 23 miles of Tracy, just inside the northeast boundary of Stanislaus County. The mine is owned by K.O. Winship estate of San Francisco and is leased by Verner Allen, also of San Francisco.The ore is principally manganese carbonate occurring in interbedded layers in white chert, with the original,carbonate mineral altered in place. Four samples, representing four types of ore, were submitted, as follows: A, black oxide; B, pink carbonate; C, gray carbonate.The Wilfred Murphy property (also known as the Murmac claims) is approximately 30 airline miles south of Tracy. The property can be reached by road from either Livermore or Patterson and is on the divide separating Santa Clara and Stanislaua Counties Calif. The ore occurs in lenses along a white-chert formation. A 2-ton sample of ore for testing was taken from a dump accumulated from assessment and development work. The Ladd mine, 13 miles from Tracy in San Joaquin County is owned by Pat J. Connolly of Tracy and is leased by Mack C. Lake of San Francisco. The ore is essentially a chert impregnated with manganese oxides and the association is therefore exceedingly intimate and complex. Samples from each of the three adit levels of the mine were submitted for ore-dressing study.As the samples differed widely in physical character and response to ore-dressing methods of treatment, beneficiation of ores from each property was considered as a separate problem. Hence results of the investigations will be prescribed in separate sections of this report."

Nov 1, 1947

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By B. J. Moore

This publication contains routine analyses and related source data for 374 natural gas samples from 24 States and 5 foreign countries. These samples were collected during calendar year 1966 as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses of foreign samples contained in this publication represent the first samples received as a result of this expanded program. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Eight previous publications have been made to present the results of 7,244 gas analyses made? by the Bureau of Mines Helium Activity prior to 1966. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related

Jan 1, 1967

By J. M. Singer

Thermal, mechanical, and physical properties of virgin and heat-treated Pittsburgh seam coal were determined as part of a comprehensive study of combustion of monolithic coal block. The information was sought to help characterize pyrolysis and combustion processes in underground coal mine fires but should also prove useful in the study of in situ and surface coal gasifiers. Measured properties include thermal conductivity, specific heat, thermal expansion, density, compressive and tensile strength, porosity, and permeability. The transport property data were obtained (when feasible) in two mutually perpendicular directions of the anisotropic virgin coal material, and coal samples carbonized for 5 hours at temperatures of 350° C, 475° C, 500° C, 650° C, and 850° C. Other coals (Pocahontas No. 3, Sewell, and Illinois No. 6 seams) were investigated for porosity and relative permeability. Interdependence among all properties was evident from the results; however, only a few correlations could be developed owing to inhomogeneity of coal material and specimen variation, which had the effect of reducing the accuracy of measurement and increasing data scatter.

Jan 1, 1979

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986