Search Documents

By R. D. Groves

Laboratory research has demonstrated that high - grade copper powders can be produced under controlled conditions from cement copper products . The technique should enable small producers to prepare a directly marketable product by means other than smelting and electrolytic purification . A continuous drum- type precipitator was the preferred unit for producing fine - sized particles of cement copper that were further processed by chemical digestion in a copper sulfate solution , by reduction and sintering in a hydrogen atmosphere , and by grinding to a powder . The effects of variables related to all stages of the process were investigated . Treatment of leach solutions from three different sources resulted in copper powders containing 99.2 to 99.8 pct Cu , apparent densities of 1.97 to 2.25 grams per cu cm , good powder flow rates , and a size distribution of 54.9 to 60.1 pct minus 325 - mesh material .

Jan 1, 1964

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By W. E. Brown, P. R. Porath, V. Miller, C. E. Wood, C. Prasky, E. P. Barrett

"INTRODUCTION This investigation was a part at the Bureau of Mines program for the production of critical and essential materials needed for the war.The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from low grade ores of Minnesota.OBJECT OF INVESTIGATIONThe investigation was conducted by the Bureau of Mines to ""determine the workability of the proposed bubble-hearth process and its possible use in connection with an experimental plant for the gasification of lignite being operated by the Coal Division of the Bureau of Mines at Grand Forks, North Dakota.ACKNOWLEDGMENTSThis report is one of many on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources.Investigations of our mineral resources are conducted by the Mining Branch, L. B. Moon, chief, and by the Metallurgical Branch, O. C. Ralston, chief.The scope of the report falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficulty beneficiated ores, the production of pure metals from domestic deposits, the exploration of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice."

Jun 1, 1947

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By R. E. Green

The Bureau of Mines undertook a bench-scale study of three different types of oxidized taconites3 from the Lake Superior district to improve the dispersion-selective flocculation-desliming process for beneficiating these materials. The response-surface contours of the effects of dissolved ionic species in the water and of three dispersion systems on the selective flocculation process were studied. Results of metallurgical data and chemical analyses of the aqueous phase showed that the water quality affects the performance of the selective flocculation process.

Jan 1, 1984

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By N. Kumar Kittusamy

A field study was conducted to evaluate seat designs on shuttle cars. Eight operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers also measured the levels of vehicle jarring/jolting. Four basic seat designs were compared on low and mid-coal seam shuttle cars during production operations at two underground coal mines. Two seats were currently used on the shuttle cars and another two were NIOSH designs. Objective data were collected using accelerometers with pre-amplifiers and filters connected to a data recorder; whereas subjective data were gathered with a visual analog scale (VAS) and a questionnaire. Results from measured levels of jarring/jolting showed that the NIOSH Seat L2A smoothed out bumps better than any other seats. Using the VAS, mid-seam and low-seam shuttle car operators rated the levels of jarring/jolting and discomfort lower with the NIOSH seat than the other seats. Questionnaire responses indicated that operators rated NIOSH seat designs as more comfortable. This research will provide the industry with better seat designs for isolating jarring/jolting in vehicles. Furthermore, researchers plan to improve the NIOSH seats using information gathered in this study.

Jan 1, 2003

By James P. Bennett

In this Bureau of Mines study, portions of four acidproof bricks (two red shale and two fireclay) were exposed to 20 wt pct RCI at 900 C for periods of 30 days. Three different techniques were selected to deter-mine volume expansion of these materials after exposure. Linear expansions ranging from about 0.02 to 0.12 pct were noted from Ta pin and dilatometer measurements. The use of strain gages to measure expansions was not successful. The red shale and fireclay brick with the lowest apparent porosities had the lowest expansions. Expansion data obtained by direct measurement of samples exposed for 30-day periods or by dilatometric measurement of autoclaved samples ex-posed for 2 h were comparable. This suggests the use of an accelerated autoclave exposure procedure for determining volume expansion effects of ceramic materials in acid environments.

Jan 1, 1985

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By Frank E. Cash

As a part of its safety program the United States Bureau of Mines has fostered the development, use, and improvement of portable electric mine lamps. Although there is still need for better illumination in mines and the replacement of open lights has been slow, improvement in electric cap lamps and increase in their use indicate one phase of recent progress toward safer and more efficient mining This report is the result of a recent survey of electric-lamp installations in the Alabama mining; district; it shows the misuse, increase in use, and relation to certain classes of accidents of these installations.

Jan 1, 1935

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983