Search Documents

By Warren W. Krech

Rock property data is needed over a wide range of parameters for the optimum execution of rapid excavation research. Eight rock types were chosen by the Bureau of Mines for a standard rock suite for such research. Large rock blocks were quarried and the standard physical and mechanical properties measured and documented. The eight rock types that comprise the rock suite are Barre Granite, Berea Sandstone, Dresser basalt, Holston Limestone, Salem Lime-stone, Sioux Quartzite, St. Cloud Gray Granodiorite, and Westerly Granite. Geologic, petrographic, physical-property, and mechanical-property test data are reported for each rock type. The information is the first step in the building of a comprehensive property listing for the eight rock types. A limited number of rock cubes are available from the Bureau of Mines Twin Cities Mining Research Center for use by researchers to broaden the information available on the suite.

Jan 1, 1974

By Jack O. Jones

The Furnish mine, Caharrus County, W. C., was operated intermittently until 1905 as a gold mine. Scheelite was discovered by A. L. Mash in the mine dumps of the Furniss and Phoenix mines, and he later informed the Bureau of Mines of his discovery. The Bureau of Mines, in two projects at the deposit in 1948 and in drilled 12 holes totaling 1,706.6 feet, examined and sampled the underground workings, excavated by bulldozer and hand, 3,155 linear feet of trenches and collected numerous samples for assay. The best scheelite shown; was found in the underground exposure of the Furniss mine.

Jan 1, 1950

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By Albert W. Deurbrouck

The performance characteristics of five hydrocyclone coal washers were evaluated to determine the sharpness and efficiency of separation that might be anticipated in commercial operation. The hydrocyclone overflows contained generally good clean coal products that would require little re-treating to remove misplaced high-gravity material. The underflows, however, contained from 63.6 to 36.7 percent of misplaced low-gravity material, which would require secondary cleaning to provide acceptable clean coal yields.

Jan 1, 1974

By Jeffrey Johnson, Carl Sunderman, Ted Williams, Stephen Signer, Douglas Bayer

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company’s Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and-MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

An active list of permissible explosives was published in December 1936 as part of Bureau of Mines Report of Investigations 3324, under the title "Active List of Permissible Explosives and Blasting Devices Approved Prior to July 31, 1,936." This list included 170 brand names. Changes in the list that have been authorized to June 30, 1937 placed 35 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Ten permissible explosives were transferred from the active to the inactive list. The present list contains 196 brand names, one explosive having been placed on the list subsequent to June 30, 1937. The brand names of the permissible explosives placed on the active list are as follows: [ ]

Jan 1, 1937

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982