Search Documents

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By L. C. IlsLey

A list of permissible mine equipment, tested and approved p or to July 1, 1934, was published in Bureau of Mines Information Circular 6813/. The present list4/ includes virtually all the electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lanes, electric hand and trip lamps, electric flood lamps, methane detectors, blasting units, storage-battery locomotives, tandem locomotives, mower trucks, and concrete mixers tested and approved by the Bureau to January 1, 1937. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the United States Bureau of Mines, to mark his equipment with a seal showing that it has been approved by the Bureau. These tests are designed to insure that equipments have the minimum requirements for safety in use. The only object of the bureau in making such tests and publishing lists of permissible equipment is to help decrease the hazards of mining.

Jan 1, 1937

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 percent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Data summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By William H. Lewis

Energy Research Corp., under contract to the Bureau of Mines, has developed a new miners' caplamp battery. The new battery is based on nickel-cadmium technology and offers significant improvements in performance with reduced size and weight when compared to the conventional lead-acid battery presently in use. This report describes the design and fabrication of the nickel-cadmium battery, which utilizes a roll-bonded electrode structure. The final battery design has a 15-A-h capacity in a 2-112-lb package, which is over 2 lb lighter than the present lead-acid caplamp battery.

Jan 1, 1983

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By K. K. Kelley

The entropy values at 298.1° K. for the elements and inorganic compounds, on which sufficient data were available for calculation in 1931, were discussed in a previous publication (96).3 Since that time the specific beats at low' temperatures of many more inorganic substances have been determined, and considerable advances have been made in the realms of spectroscopy applicable to the determination of thermodynamic properties. Moreover, a critical study of the existing vapor-pressure data made by the author (98) furnishes entropy of vaporization results suitable for obtaining approximate values of the entropies of a number of gases from the entropies of the solids or liquids. Consequently, it appears worth while at the present time to supplement the former publication, giving the new values now obtainable and making such revision in the older values as the data warrant. The methods of calculating entropies were discussed in previous publications (96, 98) and will not be repeated here. ENTROPIES AT 298.1° K. FOR INORGANIC SUBSTANCES In the following pages, the same arrangement is followed as in the previous publication (96). All entropy values are expressed in 15° gram-calories per degree Kelvin per gram-formula mass of substance. The figures given for gases do not include the effect of nuclear spin, as is nearly universally customary at present. The estimates of accuracy in the case of the values obtained from heat-capacity data apply only to the existing measurements and to the necessary extrapolations as they are made. It is assumed usually that the substances are in such an energy condition at the lowest temperatures reached in the specific-heat measurements that the usual normal type of extrapolation may be made. No allowance is made for error in this assumption. The recent work on Gd2SO4. 8H2O and FeC13 illustrates the difficulties that may arise in obtaining the entropies of some paramagnetic substances. Also the data and calculations for such substances as CO, H20, and N20 show that the correct entropy is not obtained in all cases by indiscriminate application of the usual

Jan 1, 1936

By F. A. Rutledge

The Millet copper deposit is on the north shore of Iliamna Lake in southwestern Alaska. Copper mineralization occurs in a zone of altered limestone .adjacent to and intruded by a diorite porphyry with some diabase facies. During 1949 and 1950, the Bureau of Mines investigated this prospect as a part of the U. S. Department of the Interior program in Alaska for the development of critical and strategic minerals. Field work was begun August 8, 1949; it was recessed November 28, 1949, because of inclement weather. The work was resumed Nay 28, 1950, and completed July 3, 1950. The program of investigation by the Bureau of Nines included topographic surveying, machine and hand trenching, diamond drilling, and sampling the zones of mineralization. This report outlines the general geology of the area, gives a description of the deposit, and contains the factual data resulting from work by the Bureau of Mines.

Jan 1, 1952

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile cod in the used type of byproduct-coke oven, because they expend excessively and. exert side thrust, which ruins the oven wells. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking coals with as much low-volatile coal as possible and still have a mixture that mill not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile cool has been exceeded and ovens have been damaged. It is desirable, therefore, to have a reliable method of determining the expending tendencies of mixtures before they are charged into the ovens. Furthermore, coal changes somewhat in its properties as mining progresses, end therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used. ]

Jan 1, 1938

By Eugene T. Sheridan

The 22d annual survey of the packaged-fuel industry by the Bureau of Mines, United States Department of the Interior, revealed that 26 plants in 8 States were in operation and reported production in 1956. The demand for packaged fuel in the United States has declined gradually since the end of World War II, and the number of operating plants has decreased from 70 in 1946 to 26 in 1956. Annual productive capacity of the industry has decreased also during this period, and the decrease in capacity was about proportional to the decrease in operating plants. Packaged-fuel plants are relatively small, and 85 percent of the active plants in 1956 had an annual capacity of less than 10,000 tons. The same situation prevailed in 1946, when 84 percent of the plants had a capacity of less than 10,000 tons. Total capacity for the 26 active plants in 1956 was 174,600 tons, an average of 6,715 tons per plant. Operating rates in 1956 were the highest since 1951, and the rate of production for the industry averaged 37 percent of capacity.

Jan 1, 1958

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930