Search Documents

By Richard Mainiero, James H. Rowland III

For many years there have been small scale tests available for evaluating the toxic fumes production by capsensitive explosives (DOT Class 1. l), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agents in construction and mining, there is a need to determine the quantities of toxic ti,tmes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pet) tieI oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/set for the 1 to 10 pet range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4~mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding 5 and 10 pet aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Jan 1, 2000

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By Catherine Johnson, Kelly Williams

The ability to measure the overpressure of a shock wave is necessary for explosives research such as shockwave focusing and field testing of blast-resistant designs for buildings and vehicles. To record the peak overpressure of the nearly instantaneous pressure rise at the shock front, pressure transducers with a fast response rate and streamline pencil design are needed. Time spent setting up sensors coupled with the expense of high-frequency data acquisition systems, and the inconvenience of low impedance cables can make the process challenging. Additionally, only small inaccuracies in sensor position can drastically change the measurement recorded. Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount. This paper investigates the accuracy of this method by setting dual transducer pencil probesat0and180 degrees perpendicular to the central axis of a285-gram(0.63-pound)cylindrical charge to record pressure versus time for comparison to the high-speed video. The axis of the camera lens is aligned with the central axis of the charge with both pencil probes in view. The pencil probes have two pressuretransducersset100millimeters (3.9 inches)apart to measure the time of arrival and are used to validate the velocities calculated from the high-speed images. This method can be used to evaluate the shock wave propagation from more complex prismatic charges with different cross-sectional shapes where precise placement of cumbersome pencil transducers in the near field is almost impossible.

By Dal Sun Kim, Michael K. McCarter

"Comminution (crushing and grinding) of rock materials is energy-intensive and expensive. Mucheffort has been directed to improve the efficiency of conventional milling practice, but relatively littleattention has been given to the potential benefits of blast-induced damage on comminution processes. To help assess this effect, research has been conducted at the IRECO Laboratory and the Generic Center for Comminution at the University of Utah. The objective of this research is to investigate the effect of shockinduced “crack-like” damage on rock properties and subsequent breakage efficiency for three petrologically different rock materials under laboratory conditions. In order to evaluate the effect of shockinduced damage, a quantitative measure of rock damage is needed. For this purpose, a scalar variable (0) is proposed."

Jan 1, 1993

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008

By Wendell W. Harris, Stanley J. Vitton

In the United States each year it has been estimated that expansive soils cause approximately $9.0 billion in damage to buildings, roads, airports, and other facilities. This figure alone exceeds the damage estimate for earthquakes, floods, tornadoes, and hurricanes combined. Unfortunately, some cases of expansive soil damage (swelling) are blamed on rock blasting operations if the blasting operations are located within the immediate area. While simple tests, such as the Atterberg limits test, can characterize a soil as expansive, it does not necessarily answer the question whether the foundation soils are causing distresses to a structure. In particular, it appears that once a soil has been labeled as nonexpansive it is no longer considered as a problem soil, in which case blast vibrations become the prime suspect.

Jan 1, 1996

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Paul Worsey, Gerald Rupert, Mark Kirkbride

The realignment of Highway H in the proximity of Crystal Cave (Springfield MO.) required the development of a blasting program that was both economical and efficient for construction, yet ecologically safe for the cave. Three component seismographs were strategically placed underground near prominent and sensitive cave features and the vibration levels from the construction blasting continuously monitored. Peak particle velocity (PPV) values were found to obey the square root scaling law and a peak particle velocity value of 0.3 in/sec was chosen as the safe maximum limit. This value proved adequate in preserving the integrity of the cave and its features. Scaled distances for the maximum and lower values enabled blasting personnel to select explosive charge weights per delay for given distance to the cave. Delays were determined from the dominant frequencies recorded underground.

Jan 1, 1997

By John Arrell, James Stuart

We have developed a tester that is uniquely able to measure the no-fire power level of certain types of electro explosive devices (EEDs). In the past, it has been difficult to establish a no-fire power level for nonlinear conductors, such as semiconductor-bridge (SCB) EEDs, and conductive-mix EEDs.

Jan 1, 2011

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Sharon K. Reamer, Klaus G. Hinzen

A series of controlled seismic experiments was performed in a limestone quarry in southern Germany to study seismic effects of cylindrical charges fired in both a half space (HS) (burden 63 m) and quarter space (QS) (burdens of 3 and 3.5 m) geometry. Charge columns contained from 20-32 kg of explosives and initiated from the bottom. The explosives formed a cylinder 4 m (20 kg) and 5 m (32 kg) high and 90 mm in diameter at depths from 3-8 m below ground level. Prior to each of the larger explosions, small charges of 0.12 kg seismogelit were fired at 4 m and 8 m depths in the same boreholes. Seismograms were obtained from 23 three component surface stations and up to 10 three component borehole stations (6 m depth). For each experiment, stations were located on three linear profiles of length 72 m at different azimuths from the source and one semicircular profile at a constant range of 30 m.

Jan 1, 1991

By P. Ravanal, J. Blazquez, F. Ortega, P. Couceiro, J. Navarro

Massive blasting technique is an interesting alternative to optimize mining’s performance by enhancing digging rates and overall operation’s activities, especially when a reduced operational bench width is available. The exploitation of a huge bench through multiple blasts would mean a potential reduction in productivity and higher operational difficulties. In such hard circumstances, combined with complex geotechnical conditions, a full ground vibration analysis for near and far field vibrations are required in order to safely design and conduct the blast. In this paper, a comprehensive case study will be discussed to show how the application of massive blasting techniques was safely implemented in very complex geotechnical conditions. The proposed solution was based on performing a full ground vibration study to optimize blast design parameters, such as charging and timing, in order to fire the complete bench blast in a single shooting event, without compromising the slope stability. Thus, a massive blast with an approximate tonnage of 6.0Mt was successfully designed and blasted, attending all safety and stability criteria defined by the geotechnical and drilling and blasting departments of Minera Escondida.

Jan 1, 2024

By Andrea Brickey, Ethan Marcoux

The South Dakota School of Mines and Technology (SD Mines), located in Rapid City, South Dakota, is one of only a few universities in the United States that offer a Bachelor of Science in Mining Engineering. The Department of Mining Engineering and Management (MEM) at SD Mines teaches courses that introduce students to concepts related to mining, including a course covering explosives engineering. Students are taught the basics of explosives theory and application in the mining and construction industry through a series of lectures and assignments. With limited field experience, many students find some topics difficult; these include: flyrock, ground vibration, timing, and others. Some US mining schools have an experimental mine in which they can simulate field conditions and conduct hands-on training, but not all universities have such facilities. For those without, teaching certain concepts can be more challenging in a pure classroom environment. To counteract the lack of an experimental mine, the mining department at SD Mines implemented Paradigm (Version 18.4.4984.0; McKenzie, 2017) a computerbased blast modeling software to improve the learning environment.

Jan 1, 2019

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By Doss Brittain

The term ground breaking is taken to include the process of so loosening the ground as to enable it to be readily loaded into buckets or cars and hoisted from the shaft or drift. In the Joplin district are encountered two varieties of ground, the hard and the soft. Hard ground consists of massively bedded rock requiring heavy blasting to loosen it. Such ground is to be found throughout the district in the same localities as the soft ground but more extensively, even to the exclusion of the appearance of soft ground in the sheet formation in the vicinity of Webb City. The Yellow Dog Mine at Webb City and the Grace mine on the Granby land at Joplin furnish well known examples of hardground mining which has become the most extensive in the district.

Jan 1, 2008

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By Andy Hudson, Stuart Brashear, David Lilly

Because of greatly increased timing accuracy, electronic detonator systems are a well-known and widely accepted major tool to control and reduce ground vibration. At a Southeastern quarry the authors found that the use of electronic detonators improved the reliability of the well known cubed root scaled distance equation for determining air blast. In addition, the authors noticed significant correlations between selected major peak particle velocity frequencies and air blast magnitudes. The major peak particle velocity frequency alone is a close approximation to air blast magnitudes. This relationship is not as significant or not always evident when standard pyrotechnic initiation systems are used.

Jan 1, 2009

By Scott G. Giltner, Paul N. Worsey

During the short duration of an explosive blast, many events occur which are too quick to be detected or observed in detail with the naked eye or by normal photographic techniques. Through the use of "hightech", high speed video, many of these events can be observed, instantly played back and recorded for later use. The use of a Spin Physics SP 2000 Motion Analysis System at a blast casting operation is presented. The variable range of recording speeds offered by the SP 2000 allowed it to be used for examination of different areas of blasts. At its maximum full frame rate of 2000 frames per second the SP 2000 can easily pick up the flame front as it travels down a nonel tube and the flash from the surface delays as they fire. The system was used for a variety of tasks including, but not limited to,the determination of delay accuracy to within 0.5 ms, the velocity and trajectory of the faces during blasts, and pinpointing geological problem areas. The effectiveness of the system as used on site is discussed along with detailed method of set up, recording, playback and data processing. Other details including site specific environmental and lighting problems are also covered.

Jan 1, 1986

By L. Russell Payne

The use of shock tube in the blasting industry is relatively well characterized and understood within the realms to which it is used. Non-conventional uses of shock tube within the EOD and the Aerospace Industry however has not been as widely researched and published. Characteristics of shock tube such as its reliability, simplicity and its non-electric nature make it ideal for functioning or driving mechanical mechanisms, detonators, and timing devices. Outlined in the text are the performance characteristics of shock tube in an array of atmospheric environments including pressures ranging from ambient to 100,000 ft equivalent atmosphere. In addition the useful exit work energy or impulse of the shock tube for driving these various EOD and Aerospace mechanisms is published as a function of tube lengths and atmospheric pressures. Of particular interest to these devices is the required length of shock tube needed to produce the steady state detonation energies and the accompanying properties of the shock tube at these lengths. Various sources publish an arbitrary run distance for steady state detonation and output some where between 20 cm and 1.0 meter. Statistical and experimental evidence with in the text show these numbers to be low and provides an updated reference for shock tubes usage in nonconventional situations.

Jan 1, 2008

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020