Search Documents

By S. Gajardo, E. Valdés Guerra

Together with Sociedad Punta del Cobre S.A. (Pucobre) and Orica, we are carrying out a study of alternatives for methodology of excavation in Slot Up Raises from actually built with Blind Hole (BH) to drilling and blasting (DB) methodology. The study is part of the permanent search for innovation, the use of technology and the reduction of mine operation costs. This application aims to optimize the Sub Level Stoping method, which has historically been exploited at Pucobre. Using a new variant of the method “Open Stoping”, through the initial development of ascending blind raises using a pilot drilling of a bore hole, with the objective of eliminating the upper level in order to excavate the free face opening. This industrial test aims to replace the mechanized BH Up Raise of 1.5m (4.9 ft.) in diameter and 30m (98.4 ft.) high, with a Up Slot Raise considering two separate blasting events, using different technological enablers, as detailed below: accuracy drilling with relief holes of 254mm (10 in.) diameter, high viscosity bulk emulsion, wireless initiation system and high-strength injectable bulk resin. Considering the importance of the success of this application, a DB diagram was defined to allow the opening of the up raise in two blasting events, separated by intermediate stemming deck located at the same level at a height of 15m (49.2 ft.) from the collar, using high-strength injectable resin. The first blasting event considers the first section from the collar to the first 15m (49.2 ft.), using wired electronic initiation that is detonated on the first day. A second event blasts the section from 16.5 to 30m (54.1 to 98.4 ft.), using a wireless initiation system, as, it has no physical connection, is blasted on the second day after the extraction of the material resulting from the first event. For greater precision, the design of the explosive charge configuration and initiation sequence is made, adjusted to the measurements of trajectory deviations of the actual ground drilling and is also considered for the control of the explosive charge configuration with high viscosity bulk emulsion. This application improves the profitability of the mining business by generating savings through the change of Blind Hole methodology, estimating a savings of more than 75% per Up Slot Raise

Jan 1, 2024

By Syed M. Tariq, John W. Wilson, Paul N. Worsey

The position of a major joint in relation to a blasthole has a significant effect in presplitting. Broad research into the combined effects of firing two decoupled blastholes has been performed in the past. The effects of joints simulated between two blastholes has also been evaluated. However, no attempt has been made to investigate the splitting effects produced by firing a single decoupled blasthole. This paper presents the results of such an investigation.

Jan 1, 1996

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By Travis A. Davidson, Ralph E. Burnham, Cathy Aimone-Martin, J. Kelly Ratliff

Blasters face a long list of tasks to execute daily—from vehicle inspections to blast design and layout, hole loading and tie-in, securing the site, and finally, safely executing the blast. Good practices and, in most cases, regulations and requirements necessitate documenting their work, specifically their blast report. While some blasters use paper forms, others use electronic means to streamline the process. The authors have served as attorneys and expert witnesses in representing companies and individual blasters in numerous administrative and legal matters in which documentation of the blaster’s work was both critical and detrimental to the effectiveness of defending their work. This paper discusses in a case-study manner the authors' observations concerning good blast report format, specific observations around electronic and paper report completion, record-keeping, seismograph setup and recordkeeping, video and photo documentation, internal auditing, and other topics related to documenting the blast. The paper aims to serve as a discussion guide for blasters to improve their blast record-keeping process, develop better practices that effectively document their work, and allow them to defend their work should a claim arise concerning their operations.

Jan 21, 2025

By Manuel Gutierrez, Roberto Gomez, Juan Aravena, Johan Gjoevad

The use of explosives in mining operations is a process that involves the search for an ideal explosive for the type of geological condition of the mineral to be extracted. For the explosives present on the market the majority are based on Ammonium Nitrate. This as it is an ideal balance of high energy efficiency achieved with low development of gas emission. The manufacturing and loading operation of the explosive requires multiple process stages and different raw materials, which, if is not correctly supervised and controlled may cause the development of harmful gases or, in the worst case, even toxic gases. The majority of mining operations are located at remote locations without the presence of communities, and hence individuals, which could be affected by emission of the harmful or even toxic gases. In these operations the protection is mainly to protect the employees of the operation. However, if the operation is located near communities, the effect of these gases becomes a serious problem. The communities' perception of post-blasting gases, according to interviews carried out in this project, describes these as smells of black gunpowder, damp soil with a volatile permanence and medium intensity, sometimes a stinking tone is added. The legislation in Chile that controls the exposure of “workers” to different gases is Supreme Decree 594, 2019 (Decreto Supremo 594). Currently the Chilean Ministry of Environment and Sernageomin (Servicio Nacional de Geología y Minería) are taking actions to reform and strengthen oversight, seeking through a short law to provide more tools to the government to decentralize decisions in case of non-compliance with the decree. This paper describes the development and implementation of a permanent and remote gas monitoring system, considering the reasons for choosing the gases to be included in the equipment, the types of sensors and their capabilities, the way to verify in the field the correct functioning of the technology throughout the project, and finally how the data collected in the field is meeting the government's expectations in terms of permanent and online reportability. Additionally, it addresses the continuity of gas monitoring in the community that will disappear in the short term due to the expansion of mining operations, thereby ensuring the protection of both workers and affected communities.

Jan 21, 2025

By Tom Goodell, James Cox, Scott Scovira

Resolution Copper Mining is sinking a 6943 foot (2116 m) deep shaft to access and develop a new panel caving mine with approximately 1.6 billion known tons of porphyry copper resource. This mine will take several years to ramp up to its full production level of 132,300 tons per day (120,000 tonnes per day) and is scheduled to begin production in the early 2020s. Resolution's shaft sinking contractor Cementation USA is using state of the art sinking methods combined with a largely local labor force to complete this record breaking shaft. Resolution's No. 10 Shaft has finished diameter of 28 feet (8.5m) and as of October 2013 is at the 6625 foot (2020 m) level. Upon completion in early 2014, the No. 10 Shaft will be the deepest single lift shaft in the United States.

Jan 1, 2014

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By Ronald Ticona, Anaani Huaman, Andrea Lucero

Mine-to-mill optimization begins with a clear understanding and ongoing assessment of blasting, crushing, and grinding operations. Modification of blasting practices to optimize feed size can increase a mine’s throughput. However, this is only an initial step. To optimize the entire process and fully utilize downstream equipment, fragmentation must be measured at critical points along the size reduction circuit

Jan 1, 2019

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By Ximing Yuan, Yongsheng Xu, Hongjie Li

A study of a static demolition agent that can be used underwater has been carried out. A new type of granulated static demolition agent with rapid reaction has been tested in several hundred experiments. It can be used conveniently and simply in the field. It demonstrates a fast reaction rate with high expansion pressures. The important characteristic of the new type of granulated static demolition agent is the ability to function underwater. It will destroy rock and the other brittle material without flyrock, vibration, shock wave, toxic gas or noise. The reaction rate can be controlled within 30-60 minutes. It is difficult to use these products when the reaction rate is less than 30 minutes and it is less efficient when the reaction rate is longer than 60 minutes. The reaction rate is slightly increased after the material is kept in storage for two years. A new type of the hydraulic device that is used to measure the expansion pressure of solid materials has been designed. The expansion pressure of the granulated static demolition agent has been tested with the device. It is shows that the expansion pressure of the granulated static demolition agent can get to 80~120MPa in 60 minutes. Also included is a discussion of the thermodynamics of the static demolition agent.

Jan 1, 2003

By Tom Paynter

In an underground mining environment, the primary method of firing a blast is using a combination of an electric detonator and a detonating cord to initiate the Nonelectric detonators. This method has been in use since the 1970’s. A firing line is used which can be subjected to damage and the need for constant testing and maintenance.

Jan 1, 2017

By Jorge Cárdenas Miranda, Hector Espinoza

Currently in open pit mining in Peru with double bench, it is a challenge to optimize fragmentation in the drill rows near to the slopes to ensure the performance in the loading and haulage operation along with the process in the plant. That is why the present paper addresses a previously unanalyzed variable on the effect of the discontinuity plane on the fragmentation results. From the numerical mathematical models applied through algorithms in advanced computational tools such as Elfen, it was quantified the improvement in fragmentation results as P80 through a correct pre-split plane both in its extension as well as in its width. The first results show an improvement of 30% in the P80 and ensuring the quality of the walls without damage to the matrix of the final wall. The basis developed in this paper is based on the concept of wave reflection in the free face zones where greater efforts are presented for fragmentation, a similar theory is presented in the variation of initiation sequences that seek a greater area of reflective planes in the form of "V". Cases were evaluated with a percentage of compliance of the pre-split planes from 0 to 100% evaluating the impact on the results and correlated with field information explaining the behavior and validating the benefit. From the quantification of the benefits, this work opens the possibility of focusing resources on optimizing the pre-split process to achieve an improvement in the fragmentation results, giving a greater tool in the decision to optimize the blasting process.

Feb 6, 2023

By Alyse Munro Hindley

The increasing negative public opinion toward blasting has led to stricter regulations and increased costs. This paper outlines alternative methods of rock excavation and the safety regulations and certification required by blasting professionals. Most importantly, however, it showcases the benefits and accomplishments that controlled blasting bring to society, giving the public a better understanding of the necessity of blasting in modern society.

Jan 1, 2015

By Jim Breedlove, Stephen P. Case, Mike Fabio

To meet salt production needs over the remaining life of the Cayuga Mine at Lansing, New York, the Salt Division of Cargill, Inc. decided to build a new underground screening plant. The new plant required a chamber 50 feet wide by 250 feet long and nearly 70 feet high. On advice of their mining contractor, Dynatec Mining Company, the company chose an ingenious excavation method similar to sublevel stoping. This method eliminated the need for an access ramp, reduced equipment needs and excavation time substantially.

Jan 1, 1996

By Ken Schei, Martin Reed, Samuel Bowser, John Wright

From October 18 through October 21, 2001, United States Antarctic Program blasters opened ten access holes for research divers in 11-ft. thick sea ice at Explorers Cove, McMurdo Sound, Antarctica. During this project, a blasting seismograph with a hydrophone accessory was used to monitor the underwater shock waves associated with the blasting technique. Shock wave values averaged 42.3 psi for initial (cratering) shots and 5.9 for subsequent clearing shots, indicating that the ice absorbs most of the shock wave. The results also provide data for refining safety protocols for divers and for the protection of marine biota.

Jan 1, 2003

By P. N. Worsey, M. Schmidt

Many advanced military systems and civilian power generation concepts postulate the availability of compact sources of electrical power capable of delivering gigawatts over microsecond time scales. For example, such a compact power source is essential for future practical pulsed high-powered microwave sources. An explosive-driven flux-compression power generator (EDPG) could fill this requirement. A basic strength of this concept capitalizes on the inherent high energy density storage capacity of modern chemical explosives. It relies on the physics of magnetic flux compression to convert that stored chemical energy into very large amounts of electrical power over short time scales. The generator also has the additional advantage of employing the same types of explosives that are already routinely used in conventional munitions. However, the self-destructive nature of this type of power generator places serious limitations on power pulse-lengths and ranges of applications. This paper describes how a multi-disciplinary team led by researchers from the University of Missouri-Rolla (UMR), Texas Tech University (TTU), and Texas A&M University was awarded a grant by the U.S. Air Force Office of Scientific Research to perform basic research to resolve several fundamental EDPG problem areas. Described are the utilization of UMR’s extensive explosives research expertise and facilities to investigate questions of energy conversion efficiency and the mechanics of energy production. Also, UMR explosives researchers will provide inputs to improved dynamic computer models of the complex, intertwined physics and chemistry operative in these devices. In addition to explosives expertise, UMR provides facilities for basic explosives material research, as well as the storage, machining, and formulation of explosives. UMR researchers are also using test facilities and data collection equipment at the Rock Mechanics and Explosives Research Center and at the UMR Experimental Mine to perform “proof of principle” and subscale tests of explosive-driven flux-compression power generator components. An integral part of the paper is a description of the development of an extreme intensity flash system by UMR and TTU to allow for the high-speed photography of EDPGs in operation. This multi disciplinary research program offers major advances regarding the size, weight, and electrical characteristics of compact EPDGs. Such breakthroughs could dramatically accelerate the practical realization of systems currently under study. Also, these power sources may have far reaching relevance to other Department of Defense and certain commercial compact power applications.

Jan 1, 2000

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By Charles Clark, Mark Mukhija, Jaime Klein

Comminution – the reduction in size of solid materials – is the most energy intensive component of the mining process (Bauer, 2015). It is estimated that comminution consumes around three percent of all electricity generated in the world (Ceecthefuture.org, 2017). On an energy equivalent basis, downstream processing consumes six times more energy than drilling and blasting (Kanchibotla, Sarma et al., 2014).

Jan 1, 2018