Search Documents

By Earl C. Hutchison, Gene Smith

Extensive blasting was required to construct an underground tunnel for a 90 inch sewerage relief line. The tunnel and required excavation extended under an upper middle-class residential area in Atlanta, Georgia for more than a mile and a half and required the use of more than a half million pounds of explosives in the immediate vicinity of houses and residential apartments valued at more than 16 million dollars. Other houses and property valued at more than 80 million dollars were within range to claim blasting damages. An effective blasting damage control program was carried out which limited the number of blasting damage claims to less than 2-1/2% of the total number of potential claims. All but three of the small number of blasting damage claims which were made were effectively denied without any resulting legal actions and less than $3,800 was paid for settlement of the three claims.

Jan 1, 1981

By Michael Wieland

Smoke/fume measurements from rapid transitory charge reactions are not wholly comparable with thermodynamic reaction code (TDRC) results, since quenched chemical reactions yield nonequilibrium concentrations. Though the work output and major reaction products are usually rendered with minor deviations, the toxic fumes and other minor concentrations reveal some major discrepancies. Work output for charge formulations in underwater or fixture tests were theoretically resolved with work-principal models that form a rough thermodynamic trajectory. Stalled nonequilibrium concentrations are rationalized by finding the underlying quenched reaction(s). The wide relevance of the Zeldovich radical-chain mechanism that transforms nitrogen oxide was previously recognized. The work-principal model (WPM) represents reaction quenching with off-trajectory constraints to render the fumes, without noticeably readjusting the work process. When restraints that characterize the confinement are WPM tractable, the resolution of critical reaction mechanisms is worthwhile, since they remain useful, regardless of the rich, neutral or lean stoichiometry of the charge formulation.

Jan 1, 2012

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985

By Robert Lee, Jay Rodgers, Kirk Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By J. A. Rodgers, K. C. Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By R Mancini, G Borla

This paper analyses the first results of a part of an EEC research project ("Blasting control for underground mining"). This research that involves three universities (Paris, Torino and Leoben) has been carried out at the Eisenerz test mine in Austria. In the experimental campaign here reviewed, parallel holes rounds have been fired "decomposed", which means with enough delay between the explosions of the successive blastholes groups to allow for a separate evaluation of their effects on the rock. The seismic effects have been recorded by geophones placed at small distance from the blast, the aim being to find out correlations between the features of the seismogram and the good or poor performance of the single blastholes, or of the groups pertaining to the same delay. Indeed, the seismogram is the only safe and cheaply obtainable description of what happens during the blast. The seismogram should be transformed in a diagnostic tool in the round 'calibration' stage, and in a routine control device during excavation.

Jan 1, 1995

By Bert Bahnson

As farms decrease and subdivisions increase there is a continuing demand for easy and safe silo removal. A few years ago I attended one of the Omni istribution explosive classes and was impressed by a product designed by Omni owner Bill Nixon called the Omni Breach. Its original purpose and main current use is law enforcement; specifically door breaching and tactical operations, with most of the force coming from water using a minimal amount of explosive component. I experimented with various charge strengths on concrete and found that it can be easily shattered with little flyrock or airblast. A neighbor of mine had an old silo within a foot of a barn that he was rebuilding and inquired about its removal. His property was sandwiched between an elementary school and Interstate 40, so I told him that I would do some test shots and if the results proved satisfactory, I would take the job for free to test the following theory.

Jan 1, 2006

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By Claude Cunningham

Simple bulk energy rating of explosives obscures the realities of how these deliver their energy, and diverts attention from the key question of controlling blasting results. Explosive performance is directly related to the pressure pulse impacting on the blasthole wall. This is helpfully visualised by comparing the adiabatic expansion plots for explosives of interest on the right scales and axes. The simple comparison of a pure emulsion with pure ANFO illustrates the practical significance of the intrinsic behaviour of these opposed formulations, showing that the emulsion can be expected to work more by softening rock, while ANFO will tend more to crack it. The explanation for these differences lies in the high shock, low sustained pressure of the former relative to the latter. The technique is readily applied, if a good detonation code is available and able to swap data into a spreadsheet. Any differences between codes will emerge most strongly in comparing the gamma plots.

Jan 1, 2002

By Alan B. Richards, Aleks Todoroski

The undesirable effects of blasting fumes can be controlled by minimising the amount of fume created, and by avoiding the movement of the fume plume to sensitive locations. Substantial progress has been made by the blasting industry to reduce the amount of fume typically created by blasting, but at this time no specific blast can be guaranteed to be ‘fume free’.

Jan 1, 2017

By Laurent Airaud

For around ten years, electronic detonators are available for those who want to use advanced methods and to apply theories promoted by engineers and professors to reduce blast concerns or improve fragmentation and dilution. Furthermore, decision makers can verify the use of electronic detonators to drive down mining costs. Engineers and more specifically blasters are the actual users and have to be convinced of the easiness of electronic detonators. This paper deals with electronic detonators and the notion of easiness. Common feelings about the notion of easiness are discussed. Then, examples of new technologies like, automobile, photography or Information Technology are discussed to observe how they progressed throughout time with new features and sales volume. For the specific explosive initiation industry, each step of the life of an electronic detonator is dealt with concerning the easiness and a table is used to quantify this notion.

Jan 1, 2004

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By NA NA

None

Feb 6, 2023

By Denise Clarke

Homeland Security Qualifications (HSQ) personnel were instrumental in developing the UK’s suite of Explosive Substances and Articles (ESA) National Occupational Standards (NOS) (also known as "competences") on behalf of the Standards Setting Body for Explosives, Munitions and Search Occupations (SSB for EMSO).

Jan 1, 2013

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009