Search Documents

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905

By S. P. Mishra, G. R. Chaudhury

The adsorption of Cu2+ ions by Penicillium sp. displayed a dual rate, with an initial faster phase followed by a slower one. The adsorption rate increased with increasing pH due to chemical and biochemical reactions. The Cu-loading capacity of the biomass increased at higher initial Cu2+ concentrations. Above 40 degrees C the adsorption rate decreased which may be due to partial hydrolysis of biopolymers which are essential constituents of the cell wall. Adsorption kinetics followed the Freundlich isotherm and the equilibrium concentration that was calculated on the basis of the isotherm matched the observed value well. A series of theoretical adsorption curves were produced using mathematical correlations between the mass transfer coefficient, the Cu2+ ion concentration at equilibrium and at time t. The correlation between the theoretical and observed adsorption rates for different experimental conditions was good. It was concluded that the results from the study were best explained using a mass-transfer adsorption model

Aug 1, 1995

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By T R. Meng, C Wu

After carrying out a brief review of the existing safety assessment criteria for the spontaneous detonation of explosives in the mining of sulphide ore deposits in China, and giving a detailed description of the dynamic process and mechanism of the spontaneous detonation of explosives and the relative factors, the latest research results of three kinds of explosives reacting with a group of sulphide ores are presented, based on a reliable experimental method. Afterwards, a complete safety criterion for spontaneous detonation assessment, which depends on the hole temperature, the water solution Fe2+ and Fe3+ and the pH value, is established to determine (he safe charging time of explosives in variable conditions. The criterion is verified as correct by a large-scale field test.

Jan 10, 1996

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By T. Piirainen, T. Alapieti

"The Koillismaa layered igneous complex is the result of igneous activity that occurred 2436±5 m.y. ago. Its crystallization took place in three separate but connected magma chambers, the total volume of which is estimated at more than 2000 km'. These chambers were located partly in a feeder system within Archaean granitoids and partly in an unconformity between these grani­ toids and Early Proterozoic supracrustal rocks. The composition of the parental magma that initially filled the chambers is thought to have been that of a relatively MgO-rich tholeiite. Sulphides and platinum-group minerals are mainly concentrated in the marginal series of the western part, where they are encountered over a distance of 25 km. This marginal series is an originally nearly horizontal series of rock types that displays a reversed differentiation trend, grading inwards from gabbroic to ultramafic rocks, followed bv rocks of the layered series. The chilled margin is not encountered anywhere in its original position at the contact, probably as a consequence of magmatic erosion, but remnants are to be found in the form of elongated xenoliths. Partly melted siliceous fragments from gneissic country rock typical of the lower part of the marginal series indicate pronounced contamination.Chalcopyrite, pentlandite and pyrrhotite±pyrite are the predominant sulphides. The accessory sulphide minerals include covellite, violarite, marcasite, mackinawite, sphalerite and argentian pentlandite. Platinum-group minerals are represented by froodite, michenerite, merenskyite and sperrylite. Other accessories that have been identified are electrum and native copper and gold. The mean of the Cu/(Cu+Ni) ratio in the mineralizations is 0.67 and Pt/(Pt+Pd) 0.31.It is suggested that the sulphide phase was formed in the marginal series as the solubility of sulphur in the basic magma was lowered by contamination, possibly assisted by some other factors. The sulphur isotope data support the juvenile origin of the sulphur."

Jan 1, 1984

By L. J. Cabri

Although no complete mineralogical balances have been published, the background knowledge and proven, highly sensitive analytical techniques to produce them already exist. For PGE-Cu-Ni sulphide ores a combination of ore microscopy, image analysis and electron microprobe analysis with proton microprobe analysis of sulphides for Pd, Rh and Ru and ion microprobe analysis for Pt, Ir and Rh (in some minerals) should provide the necessary data when combined with reliable assays. Other sulphide ores, such as the Cu-Ni-(PGE) ores of Sudbury, Ontario, require a similar approach except that the ion microprobe would be more suitable for the analysis of Pd, Pt and Rh because of its greater sensitivity. Oxide-silicate ores may be harder to deal with quantitatively, although the potential to confirm the presence of trace PGE within silicates and oxides may be greater than in PGE sulphide and Cu-Ni-(PGE) sulphide ores. However, solid solution of PGE in oxides and silicates still requires thorough documentation and evaluation in terms of their significance for the overall metallurgical balance

Apr 1, 1994

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By D. M. Evans, D. L. Buchanan

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. The Zinca area was chosen as a suitable location for an investigation of the weathering and secondary dispersion of platinum group metals from the Zone. It was concluded that platinum is immobile while within weathered rock, its mineral phases tending to alter from primary sulphides and tellurides to secondary Pt-Fe alloys. Palladium is variably mobile in weathered rock. In stream sediments Pt occurs mainly as small, dense, discrete particles, giving rise to a nugget effect, whereas Pd probably occurs as much finer particles or chemically adsorbed on to a suitable substrate. Pt shows a rapid decrease in sediments downstream from mineralisation, whereas Pd has a much slower downstream decay

Apr 1, 1994

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By C. C. Harris

The two best known graphical methods for presenting and comparing comminution data are obtained by linearising the Gates-Gaudin-Schuhmann and the Rosin-Rammler size distribution equations. It is shown that the Gates-Gaudin-Schuhmann equation can cause excessive congestion in the 50 per cent oversize range and that, overall, the Rosin-Rammler is a better procedure. Examples are given

Dec 1, 1971

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By P Cochrane

Our ability to generate information and transport it about the planet on super highways of optical fibre is about to change the way in which we communicate, work and live. There is not a single aspect of our future that will go untouched by the communication and computing revolution that Is now upon us. The change we are about to witness will overshadow the impact of the printed word, industrial revolution and physical transport. The next major wave of information technology (TT) development will focus on the delivery of information and experience on demand, in the right form, at the right time, at the right price, to fixed or mobile terminals anywhere, over networks of optical fibre, radio, satellite and optical wireless. Bandwidth, distance and time will no longer be significant cost elements as service and access become dominant.

Jan 7, 1996

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

A study of the thermodynamic properties of magnesium chloride ammines was carried out with the ultimate objective that the thermal decomposition of the hexammine MgCl2.6NH3 may prove successful on a commercial scale for the manufacture of anhydrous magnesium chloride, which is required for the efficient electrolytic production of magnesium. The experimental data are presented in the form of an equilibrium diagram that aids the understanding of the conditions associated with the thermal decomposition of ammines

Jun 13, 1905

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971

By M. K. Abd El-Rahman

A complete chemical analysis of the waste showed that it contains 15.64% P2O5; X-ray diffraction analysis revealed that it is composed mainly of francolite, calcite, pyrite, quartz and dolomite. The phosphate values were recovered and the settling rate of the wastes enhanced by the use of hydrocyclone and flocculation techniques. The hydrocyclone produced an underflow enriched in phosphate and an overflow enriched in clays. The former represented 39.8% by weight of the phosphatic clay waste and assayed 26% P2O5 at a recovery of 66.36%. The results of flocculation of the phosphatic clay waste showed that both the degree and rate of settling were increased and that the process water could be recycled. The settling rate was 37 times greater when anionic polyacrylamide A130 was used

Jun 21, 1905

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905