Search Documents

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By X. Q. Wu

Magnetization in slurry (MIS) of weakly magnetic minerals by iron ions was investigated. The magnetic seeds (strongly magnetic particles) were synthesized by ferruginous chlorides directly in slurry instead of previous preparations of magnetic seeds by finely grinding mineral magnetite or specially synthesizing them separately in an aqueous solution. In this way, the growth of the seeds and their adsorption on the minerals simultaneously take place in the same slurry. That after MIS the recovery of weakly magnetic mineral limonite in a magnetic separator increased means the formation and adsorption of magnetic seeds on the surface of iron mineral limonite. The magnetization effect was evaluated by limonite recovery at a magnetic strength of 3.500 Gs in a magnetic separator. Mineral limonite was properly magnetized in the following slurry condition: molar ratio of Fe3+ to Fe2+1:3, slurry temperature of 45 °C and pH 10.5. The selectivity of the magnetization between minerals limonite and quartz was improved by adding surfactant sodium oleate.

Jan 1, 2014

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

Due to complex mineralogical and chemical interactions of the value and gangue mineral phases present in uranium-containing lateritic ores, deleterious pulp gelation which impacts on value metal recovery sometimes occur during atmospheric leaching. In this study, the leaching behavior and particle interactions of selected oxide (hematite, quartz) and clay minerals (muscovite, chlorite), which constitute predominant host gangue phases of typical lateritic uranium ores are investigated to provide basic, mechanistic understanding of temporal pulp gelation phenomenon. Isothermal, batch leaching with H2SO4 was carried out on concentrated dispersions (30 ? 57 wt.%) of single minerals at pH 1 and 25 or 70 °C and their concomitant solution, speciation and rheology (shear yield stress, viscosity) were characterized. It is clearly shown that despite the high oxide content of lateritic ores, the pulp chemistry and rheology is largely affected by the incongruent leaching behavior of more reactive, acid-consuming aluminosilicate clays. Furthermore, time- and temperature-dependent alumino-silicate species polycondensation interfacial reactions are shown to be responsible for the enhanced particle interactions, reflecting strong pulp rheology in agitation and pumping. If not properly mitigated, high pulp shear yield stress and viscosity have a striking impact on processability and hence, value metal recovery.

Sep 1, 2012

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By Jan Svoboda, Toyohisa Fujita

The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation in magnetic separation are identified, advantages of this technology in comparison to other physical methods of material manipulation are discussed and reasons for its failure to live up to its potential and expectations are indicated. Derailers that were responsible for the implementation failures are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.

Jan 1, 2003

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

In the present work, the influence of coagulant, polymeric flocculant structure type and mode of addition on flocculation performance and dewatering behaviour of plant mineral waste tailings of diverse mineralogy (kaolin, quartz, goethite/hematite feldspar, gibbsite, rutile, and Illite) is investigated. High molecular weight, non-ionic polyacrylamide homopolymer and anionic (acrylate) and cationic (quaternary acrylate) copolymers were used in orthokinetic flocculation of colloidal-ly-stable, aqueous dispersion of negatively charged particles. It is demonstrated that, through prudent selection and mode of addition of polymer structure types, synergistic effect between certain cationic and anionic flocculants can be readily achieved, leading to significantly improved dewaterability of the heterogeneous mineral waste tailings.

Jan 1, 2014

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By Tilak Raj Mankhand, Mudila Dhanunjaya Rao, Kamalesh K. Singh

"Zinc dust is used for the removal of primary impurities by cementation from the zinc sulphate electrolyte before electrowinning of zinc. However, the industrial zinc electrowinning plants has been reported that the zinc dust consumption is in large excess than the stoichiometric requirement. In the present investigation, morphology of the zinc dust has been altered by ball milling and utilized for the cementation of cadmium, which is one of the major impurity and compared the change in the rate of cementation with original zinc dust. Initially, 325 mesh size zinc dust was used for the optimization of the excess quantity of zinc dust to be used at a temperature of 50 °C. The chemical analysis of zinc dust before and after ball milling and morphology were studied by scanning electron microscopy (SEM), and the solution was characterized by Atomic Absorption Spectrophotometer. The rate of cementation increased with increase in ball milling time. The residual precipitate obtained after filtration was also characterized by X-ray diffraction analysis. Finally experiments were conducted to study the effect of temperature and kinetics of cadmium cementation using first order reaction kinetics. Based on the integral method, the calculated activation energy for the cadmium cementation with 4-hours ball milled zinc dust was found to be 3.39 KJ/mole. INTRODUCTION Primary production of zinc in the world is carried out by hydrometallurgical route. The primary impurities in the neutralized zinc sulphate solution that cause negative effect on electrowinning are copper, cadmium, cobalt, and nickel. Copper diminishes the current efficiency and cadmium contaminates the cathode zinc (Morgan, 1977) while electro winning. Nickel and cobalt lead to perforation in the zinc deposit and prevents the electro winning process (Abrasheva et al, 1984). Due to higher electro positivity of these metal impurities than zinc, they can co-deposit with cathode zinc at the time of electrolysis. In addition to that, some possible impurities (including cobalt) in the electrolysis may lower the hydrogen overvoltage, allowing deposition of hydrogen at cathode resulting in fall of current efficiency. The deposition of zinc on the cathode is possible only at higher hydrogen overvoltage which is practicable in the absence of such impurities (Raghavan et al., 1999). Cementation is one of the prominent purification technique, and in that less reactive metal can be replaced by highly reactive metal by allowing them into precipitation. Cementation of cadmium from zinc sulphate electrolyte is being done by the addition of zinc dust."

Jan 1, 2018

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By P. Matias

The study involved two projects that will produce copper concentrate and may have their operations integrated. Transport by trucks, conveyor belt, and the equipment called RopeCon were evaluated as options for the ore transport between the sites. A rainforest stretch, that Vale S.A. demands to preserve, is situated between the projects. It was suggested to further review RopeCon because it presents minimal interactions with the environment. To design the preliminary system layout, a research was done on the rainforest cover height data, but the information found was scarce and imprecise. For preserving the local forest, the use of this data would conduct to the oversizing of RopeCon towers and, consequently, overestimation of its costs. For the acquisition of reliable information, a method was developed using local data acquired through airborne laser survey. The volume between the digital surface and terrain models was calculated to generate a surface representing the forest cover height. It was revealed, by plotting the points obtained from this surface, that 85% of the vegetation is below 25 m. This height is suggested to review the preliminary project with a more accurate design of the equipment towers, thus reducing its costs estimates. The method permits the precise location of the large trees, making easier to find a pathway, for linear-shaped facilities, that would minimize the creation of vegetation-free zones as a measure to protect equipments against falling trees and forest fires. Keywords: forest cover, mining projects facilities, digital models, airborne laser survey

Sep 1, 2012

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By J. J. Lui

Surfactant plays a critical role in many industrial processes such as petroleum, mining, environment and food processing, and daily life. For ionic surfactant systems, adsorption of surfactant at oil-water interface imposes a net charge to the interface. The nature and magnitude of the charges at the oil-water interface depend on charge characteristics of surfactant molecules, concentration of surfactant and solution pH. In our previous study, zeta potential measurement of hexadecane drop-lets in industrial process water was shown to be a simple, yet powerful method for identifying various types of ionic surfactants present in the aqueous system. In this paper, the site-binding model was applied to prediction of zeta potential of oil droplets in aqueous solutions containing a mixture of cationic and anionic surfactant molecules. The total number of interfacial sites for various types of surfactant involved was determined by applying the Gibbs adsorption equation to the measured interfacial tension-surfactant concentration profiles. The distribution of various types of surfactant molecules at the interfaces was evaluated by Langmuir isotherm constants. With the ionization constant of surfactant taken from the literature, the predicted zeta potentials of oil droplets in surfactant solutions from site binding model were shown in a reasonable agreement with the measured zeta potential values.

Jan 1, 2014

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By Xiaodong Jia, Williams. Richard A.

This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. The ability to predict packing structure of real particle shapes and to compute directly some structure-dependent physical properties (such as liquid permeability, mechanical strength/ stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.

Jan 1, 2003

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018