Search Documents

By Jan Svoboda, Atsushi Shibayama, Toyohisa Fujita, Toshio Miyazaki, Kenji Murata

"The electrical disintegration (ED) method and disintegration by underwater explosion were investigated as new fragmentation techniques for the kimberlite ore and tungsten scrap of superalloy (carbide bit). The results of various breakage tests demonstrated that both fragmentation methods as new disintegration techniques for recycling were able to liberate various components of materials of different resistivity and elastic impedance.SUMMARYThe breakage of the kimberlite ore from South Africa (sample size: 15 mm x 15 mm x 6 mm) was achieved by the ED method. A relationship between the sample size, voltage, the electrical current and the energy needed for the disintegration was found from the experimental results. Kimberlite exhibited a high degree of breakage, when the high voltage of 60 kV and the pulse current of approximately 5000 A were applied to the sample by the generator during 0.2 microseconds (Fig. 1)."

Jan 1, 2003

By M. Evertsson, K. Bhadani, E. Hulthén, M. Bengtsson

"Modelling and simulations for mineral processing plants have been successful in replicating and predicting predefined scenarios of an operating plant. However, there is a need to explore and increase the potential of such simulations to make them attractive for users. One of the tools to increase the attractiveness of the simulations is through applying optimization schemes. Optimization schemes, applied on mineral processing simulations, can identify non-intuitive solutions for a given problem. The problem definition itself is subjective in nature and is dependent on the purpose of the operating plant. The scope of this paper is to demonstrate two optimization schemes: Multi-Objective Optimization (MOO) using a Genetic Algorithm (GA) and Multi-Disciplinary Optimization (MDO) using an Individual Discipline Feasible (IDF) approach. A two stage coarse comminution plant is used as a case plant to demonstrate the applicability of the two optimization schemes. The two schemes are compared based on the problem formulations, types of result and computation time. Results show that the two optimization schemes are suitable in generating solutions to a defined problem and both schemes can be used together to produce complementary results. INTRODUCTION The comminution process for a mineral processing plant consists of multiple crushing and classification stages and aims to produce fine material to liberate ore from the minerals. The modelling and simulation of such processes are well established using static process models (King, 2001; Napier-Munn et al., 1996). A recent development in the dynamic modelling for such processes has shown further increase in fidelity compared to the static process models (Asbjörnsson, 2015). The developed simulations can be utilized to design, operate and control mineral processing plants based on the requirements of users (Bhadani et al., 2017). Typically, the requirements in the operation of the comminution process are conflicting in nature, as for instance, reduction of power draw by process units, maximization of production of fine materials, and increasing utilization of the process units. These conflicting requirements leads to a Multi-Objective Optimization (MOO) problem to operate a mineral processing plant. The MOO problems are normally referred to as non-linear problems and its fundamental understanding with respect to process behaviour is difficult to achieve."

Jan 1, 2018

By Y. S. Sun, P. Gao

Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time, coal addition, feed thickness and size of Australia iron ore. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67% was obtained at a Fe recovery of 87.82% under optimum reduction conditions where a metallization rate of 85.82% was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations. And the results indicated that theiron minerals such as hematite and limonite in the Australian iron ore were reduced as follows: Fe2O3?Fe3O4?FeO?Fe. Furthermore, the metallic iron particles produced by reduction increased in size with longer reduction times.

Jan 1, 2014

By Herman D. Mendoza

"The removal of finely dispersed mercury from the effluent of small-scale gold mining operations and the eventual recycling of the recovered mercury was investigated. The conventional method of amalgamation, or “ball milling”, involves the mixing of a substantial amount of mercury with ore to recover free gold during the grinding stage. During grinding, a portion of the mercury is transformed into minute droplets, which readily float and disperse in the effluent. A kilo of gold ore containing 20-30 g Au/t, when ground with 3 g of mercury, yields 0.005 to 0.050 mg/l of mercury in the effluent, exceeding the concentration of 0.002 mg/l allowed by law for surface water.A rapid recovery/ recycling process was introduced using the surface-chemical properties of finely dispersed mercury in aqueous suspension. It was observed that fine droplets of mercury in an aqueous environment readily attached onto a collector having positive surface potentials for pH 3 to 10. An example of a suitable collector is alumina (Al2O3), which has an iso-electric point of pH 9.8. When an effluent, coming from a settling procedure after an amalgamation-grinding stage, was passed through a column-bed packed with alumina fiber, removal and subsequent collection of finely dispersed mercury occurred under acidic conditions, pH 3-6. Recovery was around 99.5%, yielding an acceptable quality of water safe for disposal into the aquatic environment. The collected droplets of mercury, which are left in the column-bed of alumina fiber, were subsequently treated with a cleansing solution at alkaline conditions pH 10 -12. At these conditions, both mercury and alumina fiber carry negative surface potentials, which results in the eventual detachment of attached mercury from the alumina collector. The effective recovery of attached mercury from the alumina collector by the detachment procedure is only 30-35%. The collected mercury from the cleansing stage can be collected, cleaned and can be used for subsequent amalgamation processes. The attachment and detachment behaviour of finely dispersed mercury onto and from the microscopic collector alumina is shown in Figure 1. The result of attachment and detachment were analyzed using existing interaction energy theories like the Darguin-Landau- Verwey- Overbeek (DLVO) Theory."

Jan 1, 2003

By O. D. Khmelnitskaya

The research on selecting of an efficient technology of pyrite cinders complex treatment, sulfuric acid production wastes, have been made. The grades in the initial product were 2.04 g Au/t, 35.0 g Ag /t, 0.38%Cu, 1.1% Zn. Laboratory tests on cyanide technology, thiourea and sulphite leaching were carried out. Magnetic and flotation beneficiation and biohydrometallurgical technology were tested. After considering the results of the tests, the most economically efficient technology of pyrite cinders complex treatment with cyanide leaching of precious metals was determined. The technology involves water washing of soluble copper and zinc compounds, lime treatment and cyanide leaching of gold and silver, detoxification and utilization of mineral wastes. The precious metals are recovered from solutions by cementation onto zinc. Copper is recovered from rinse waters by SW/EW and then zinc is precipitated as hydroxide. All the solutions and organic agent are used in recirculation and therefore the technology is practically waste-free. Mineral wastes can be used as iron-containing materials for cement industry. The technology has been tested in pilot-plant scale under continuous operation with complete re-circulation of cyanide solutions. In this process recovery of 54% Au, 45% Ag, 30% Cu and 50% Zn has been achieved.

Jan 1, 2014

By Thomas Mütze, Michael Klichowicz, Mathis Reichert, Holger Lieberwirth

"Self-similarity is proofed to be a common feature when brittle material is comminuted, either in particle bed or single particle mode. Appropriate test work is well documented for particle sizes less than 7 mm in several publications. In contrast, almost no research has been done for coarser particles. The aim of this paper is to show that the fracture pattern of coarser material also tends to be self-similar. Hence, single particles of quartzite, granodiorite and dolomite were comminuted under compressive load. The focus was set on three different size fractions -3.15 +2.5 mm, -31.5 +25 mm and lumps -300 mm. According to the wide range of particle sizes, three different piston-die presses were used with a maximum compressive force ranging from 5 kN to 4000 kN. The force-displacement curves were recorded in order to calculate the specific comminution energy. Additionally, the -31.5 +25 mm size fraction was crushed in a laboratory scale jaw crusher and a roll crusher. Some authors report that the energy-size-reduction relationship of self-similar materials can be approximated by a linear function, which is independent of the comminution equipment. In their charts the slope can be seen as a product-size-independent grindability measure. Our tests show a self-similar breakage behavior when particles in a range of -300 +3 mm are comminuted in single particle mode. Furthermore, the products of the piston-die-presses and the roll crusher are similar to each other in a self-similar representation of the particle size distribution. The jaw crusher product, however, is not self-similar compared to the piston-die-press products. Finally, the linear energy-size-reduction relationships are confirmed for each fraction, but show size dependent slopes."

Jan 1, 2014

By N. Karapinar

Ferrihydrite, a member of iron oxides family, has been used as an adsorbent for the removal of heavy metal ions from industrial wastewater. The success of the operation depends mainly on the efficient removal of ferrihydrite from the aqueous phase. Hence, the emphasis of this study was given on the separation of ferrihydrite by high gradient magnetic separation (HGMS) method to overcome solid-liquid separation difficulties of ferrihydrite. Magnetic seeding technique in which the magnetite mineral was chosen as a seeding reagent was used to make magnetic separation available. The method clearly involves the attachment of ferrihydrite to a magnetic seed material and subsequent magnetic separation of ferrihydrite ? magnetite coagulates. Seeding of ferrihydrite with magnetic particles was achieved by exceeding the solubility limit of the ions in the presence of dispersed magnetite. Magnetic separation results of seeded ferrihydrite showed that maximum seeding performance is obtained in the pH range of 7.0~10.0. Iron/magnetite ratio had a marked effect on the separation of seeded iron oxide precipitate by HGMS. This ratio determines the operation parameters such as magnetic field strength and flow rate. It was concluded that when used with magnetic seeding technique, HGMS can be used to surpass separation difficulties of ferrihydrite used in adsorption-based treatment techniques.

Jan 1, 2014

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By T. Fujita

A high-grade fluorite ore is converted into hydrogen fluoride to produce many kinds of materials containing fluorine. Recently, it is becoming necessary to use low-grade fluorite ore due to the depletion of high grade ore. The low-grade fluorites usually have impurities such as SiO2, P, CaCO3 and arsenic. The most impurities such as SiO2, CaCO3 and P can be removed by using flotation method. However, the removal of arsenic is difficult, and the arsenic contamination decreases the hydrogen fluoride production percentage. The novel technologies for processing low-grade fluorite ore are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, the removal of arsenic from low-grade fluorite ore has been investigated by means of an autogenous grinding using tower mill in sulfuric acid aqueous solution and 0.3 mm zirconia balls in water. The nano grinding in water can prevent the dissolution of 0.3 mm size zirconia balls as grinding media by sulfuric acid solution. Experimental results showed that the arsenic concentration was reduced from 260 mg/kg to 90 mg/kg and CaF2 recovery reached 90% by this process.

Sep 1, 2012

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.It was found that the digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was a merit to apply the sludge to agriculture in dry areas. Anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion. The anaerobic digestion sludge could be considered as a humus-rich hygienic product that improves soil fertility and water holding capacity, nourishes plants and immobilizes heavy metals in the environment"

Jan 1, 2003

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

By Herman Mendoza, Luisa Ciriaco

An investigation of the seeding mechanism using heterocoagulation and the Derjaguin - Landau - Verwey - Overbeek (DLVO) theory of two pure minerals is the objective of this study. The seed was silica with modal diameters of 4.529 µm (fine particles) and 5.216 µm (coarse particles) and the test powder was hematite with a modal diameter of 0.883 µm. Parameters included variations in the concentration and particle size of silica. Both particles were first subjected to size determination and settling tests via Stoke’s Law. The silica-hematite system was then suspended in 0.001 M KNO3 electrolyte solutions where pH was adjusted. Afterward, the suspension was agitated and was allowed to settle at different time intervals while obtaining turbidity readings. Results through settling time and turbidity vs. pH graphs indicate that maximum heterocoagulation occurs from pH 2 to 5 while minimum heterocoagulation occurs from pH 6 to 7. At these pH levels the zeta potentials of silica and hematite are negative and positive, respectively. On the contrary, repulsive forces dominate the system from pH 8 to 11 due to the particles’ negative zeta potentials. Furthermore, the attachment of hematite to silica increases when the parameters become larger thereby increasing the effectivity of heterocoagulation at acidic to neutral pH levels.

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

By Ye Junjian

The feed ore is the concentrate of low intensity magnetic separation of pyrite tailings, containing TFe47.47%, S19.41% and SiOpyrrhotite. The exploratory tests showed that using a process of flotation followed by magnetic separation could respectively obtain a sulphur concentrate of S 31.08% with a recovery of 82.89%, and an iron concentrate of TFe 59.97% and S 9.52%with a recovery of 30.93%. The reason of iron concentrates with high sulphur grade was that the sulphur grade of flotation tailings was 7.03%. So enhanced flotation for pyrrhotite was investigated in this research. Results show that when the natural pH of ore pulp varied from 5.5 to 6.0, a reagent combination of FS, LH, and BJ displayed the optimum flotation performance for pyrrhotite. After comparisons made on different flotation processing, the previous flotation flow of ?one roughing, one cleaning, one scavenging system and middling reprocessing?, was found, among others, to have the best flotation effect, as the grade and recovery of sulphur concentrate were 31.08% and 82.89%, respectively, and sulphur content of the flotation tailings was 7.03%. The above results indicated it was difficult to raise further the effect of flotation desulphurization. The authors therefore suggested that oxidizing roast should be adopted following the magnetic process for the purpose of further desulphurization. Besides, flue gas containing SO2 8.25%. And the valuable minerals are magnetite and 2 generated from roasting could be reused for sulphuric acid production. Keywords: pyrrhotite, enhanced flotation, desulphurization

Sep 1, 2012

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By S. Swaroopa

Copper-chromium mixed oxides are widely used as catalyst for organic chemicals industry, NOx and CO oxidation, solid propellant etc. In the present investigation, one such spent Cu-Cr catalyst has been tested for recovering copper and chromium values through hydrometallurgical route. The spent catalyst used in this study contains about 42% Cu and 36% Cr. Phase analysis through XRD indicates that major phases are copper chromium oxide (CuCrO2) and copper chromate (CuCr2O4) while minor phase is copper oxide (Cu64O). SEM images show that high energy ball milling changes surface morphology significantly ? more regular shaped grains in unmilled samples changed to fine agglomerates. Surface area also changes significantly due to milling. Preliminary leaching experiments with NH3 and H2SO4 media using unmilled samples indicate that both the media are suitable for selective extraction of copper. About 55% copper recovery is achieved in 2 h using 1.2 M NH3 + 0.2M (NH4)2SO4 solution at 100°C. Increasing NH3 concentration or temperature does not improve the recovery significantly. Under the above conditions chromium, dissolution is insignificant (max. 2.24%). XRD analysis of the residue indicates that copper chromate fraction (CuCr2O4), which is a spinel structure, remains mostly intact. In sulphuric acid media at ambient temperature, 47% copper recovery is achieved with 7.5% (v/v) H2SO4 and maximum of 57% with the increase in acid concentration to 20%. However, 67% recovery is achieved by increasing the leaching temperature to 150°C. High energy ball milled samples show improved leaching efficiency. Under the leaching conditions of 7% H2SO4 (v/v), 2% pulp density, 80°C an unmilled sample yields 47% Cu recovery whereas 3h and 5h milled samples yield 65% and 90% Cu recovery respectively in 2h leaching time. Influence of temperature is also more pronounced in milled sample leaching in comparison to unmilled sample. Water leaching of alkali (NaOH) roasted milled sample carried out at 750°C for 2 h with 100% NaOH (w/w) resulted in 80% Cr recovery as compared to 37% Cr recovery using unmilled sample under the same conditions. Keywords: spent catalyst, copper, chromium, leaching, mechanical activation, roasting

Sep 1, 2012

By Z. Y. Ma, M. D. Liu, Z. Z. Liu, J. K. Zhou

"An optimization method of microwave assisted leaching of copper anode slime was proposed based on Taguchi method. The results showed that the solid-liquid ratio was the most important factor affecting SNR(signal noise ratio) of the copper, tellurium and selenium leaching efficiencies, and its contributions to the copper, tellurium and selenium leaching efficiencies were 58.34%, 55.54% and 60.74%, respectively. Solid-liquid ratio was a significant factor to SNR(copper, tellurium and selenium). Reaction period was a less significant factor to SNR(copper and tellurium) and concentration of sulphuric acid was a less significant factor to SNR(selenium) while microwave power was an non-significant factor, its contributions to the copper, tellurium and selenium efficiencies were 3.22%, 11.73% and 12.73%, respectively. The optimized parameters of the microwave assisted leaching of copper were as follow: microwave power of 500 W, reaction period of 10 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The optimized parameters of the microwave assisted leaching of tellurium and selenium were as follow: microwave power of 800 W, reaction period of 15 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The validation experiments under the optimized conditions has been carried out, the copper, tellurium and selenium leaching efficiencies were 98.66%, 84.32% and 64.54%, respectively. INTRODUCTION As important valuable by-products, copper anode slimes are collected from the bottom of the electrolytic bath in the electrolytic copper refining process(Kilic, 2013). The value of the anode slime is determined by the content of rare metals and precious metals(Liu, 2014). Generally, pretreatment of copper anode slime is the first stage of the whole process. The aim of the pretreatment process is to remove Cu, Te and Se etc and enrich the valuable metals. The methods of pretreatment process can be differentiated into: pyrometallurgical processing and hydrometallurgical processing(Amer, 2003). The hydrometallurgical processes are more promising compared to pyrometallurgical processes in terms of cost effectiveness, low energy consumption and environmental concerns(Ranjbar, 2014). However, the disadvantages of the hydrometallurgy process are evident, such as lengthy processing times and low efficiency. Therefore, it is necessary to develop a highly efficient and environmentally friendly pretreatment method."

Jan 1, 2018

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018