Search Documents

By D. Waite

The Chairman opened the session by wondering why so few papers on Maritime Structures had been received for this conference. Perhaps because the marine environment is so hostile and the access so difficult that engineers tend to be more prudent about new ideas and designs. Dennis Waite noted the number of grey hairs in the room - grey hairs which could be equated with experience gained the hard way. He hoped that this experience would be passed on in the discussion period of this session. The Chairman was delighted to welcome two authors from China, Mr Sun and Mr Liang. He was most grateful on behalf of the conference for their efforts both in preparing their papers and for being able to present them. He regretted that Messrs Noce and Fedolino were not able to present their paper and then welcomed Mr Christensen from Denmark who would present the first paper.

Jan 1, 1991

By Partha Sircar

"For Berth 22 modifications at the Port of Oakland, nearly 600 octagonal 24-inch ‘diameter’ precast-prestressed concrete piles were driven, some piles over 160 feet long. Prior to production pile driving, an indicator/test pile program was performed, which included extensive use of dynamic load testing with (Pile Driving Analyzer (PDA) & CAPWAP analyses. The indicator test-pile program resulted in requiring significantly longer piles than the original design based on subsurface borings. The cause of this discrepancy is investigated in light of the available geotechnical information, soil mechanics principles and standard techniques for pile capacity computations. Several interesting phenomena emerged. These include relatively low resistances offered by crushed rockfill than would conventionally be assumed, non-homogeneity of an apparently uniform formation and the effects of jetting on pile side friction. Also revealing was the significant increase in capacity between 1 and 3 weeks of driving for long piles in clay. Recommendations were developed for pile capacity for future use as “lessons learned”.IntroductionThe foundation for the replaced Berth 22 structure at the Port of Oakland in California involved driving approximately 570, 24-inch octagonal precast prestressed concrete piles. A plan and a section for the pile locations are presented in Figure 1.The ultimate loads on the piles used in the design are presented in Table 1 – the loads are quite heavy.The foundation design was followed by an extensive Indicator Pile Program. The contractors (Manson Construction Co. of Richmond, California) opted to use a Delmag D62-02 diesel hammer (Rated Maximum Energy – 165 kip-feet). Per the project specifications, the same hammer was used for both indicator and production pile driving. The production piles of appropriate lengths were ordered based on thr results of the Indicator Pile Program. A number of interesting results were found from the Indicator Program, which is discussed in this paper."

Jan 1, 2015

By George G. Goble

In the middle of the nineteenth century, the dynamic formula appeared as a description of pile penetration during impact driving. The simplicity of use of the formula combined with the power of the energy concepts behind the formula caused it to be quickly accepted and integrated into practice. Dynamic formula had been in use for 100 years when the Wave Equation computer programs first appeared. With that long experience it is not surprising that the formula continued to be used and were only slowly abandoned. The Wave Equation offers many advantages over the various formula but it does not offer a clear sense of physical understanding of pile driving that is available with the formula. Large amounts of numbers are generated but often it is difficult or impossible to gain a physical understanding of the results or a feeling for the importance of the various parameters. The question that the Wave Equation user has is, "What will happen if I use a larger drive cap (or change any other item of equipment)?" In this paper, I will attempt to explain pile driving using elementary wave propagation theory. However, the presentation will not depend on any higher mathematics. With the use of wave mechanics, it is possible to explain driving characteristics that cannot be handled with the energy formula.

Jan 1, 1995

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By W. J. Kingwell

My comments and questions are addressed to Mr. Troughton. It seems to me that the tests were very well tailored to determine long term effects on performance of bearing piles as groundwater pressures rise in the London Basin. This rise is being simulated by means of a groundwater recharge system but it would be informative to have further details of the controls of conditions simulated. Ideally the porewater pressure in Standpipes 1, 2 and 3 should be the same throughout the test. Under test conditions are there not practical dif­ficulties? Recharge Well C2 is a lesser dis­tance from the pile than the other wells. Was the rate of recharge to C2 regulated to a lesser rate than the other three? In my experience the rate of acceptance usually varies from well to well. Under a common feed pressure were mea­sures taken to compensate for this? Since the problem does not only affect London, but also Liverpool, Nottingham, Birmingham and to a lesser extent, Manchester, I question whether an ideal procedure is being used. It is well known that rates of acceptance decrease with time and often recharge wells need to be flushed out at regular intervals. Other pro­cedures may need to be adopted to accurately simulate the effect of groundwater rise, if tests of longer duration are to be considered.

Jan 1, 1991

By Slav Tchepak

The King's Wharf development is located in Sydney's Darling Harbour area. The site was originally used for industrial maritime purposes, which over the years has been reduced to accommodating leisure craft only. The site has been filled with various materials, resulting in fill materials varying from soils, to concrete and rock fill. A prestigious new residential development at the site required piles to found in Sydney sandstone that occurred at depths ranging from 1 to 27m. The selection of appropriate pile types is discussed, as are details relating to the design and construction of cast insitu Omega piles and CFA piles. A number of issues needed to be addressed relating to the piling, including the design of the piles, the potential for liquefaction of the fill material due to earthquakes, penetration of the piles through the fill materials, installation of the piles to a satisfactory positional tolerance and pile performance. A number of piles were dynamically tested to prove pile performance and these results are presented and compared with design expectations. The project was successfully completed on time and budget, indicating the selection of pile types in the difficult ground conditions to be appropriate.

Jan 1, 2000

By James J. Tansey

A Deep Foundations Institute meeting with the University of Michigan at Ann Arbor in March of 1984 featured legal rights under Differing Site Conditions. A workshop conducted by the authors and Gerard Ittig, Esq. added to the value of the symposium. This paper will be of interest to your attorneys in any subsurface disputes.

Jan 1, 1985

By Carole L. B. Mitchell

The increased use of micropiles and soil nailing presents a growing database of verification and sacrificial load test data. In Washington State, the use of micropiles is becoming common, and soil nails are now almost as widely used as tiebacks; yet the state of the practice in understanding load transfer rates has not improved. This research compiles load test data for micropiles and soil nails from Shannon & Wilson?s records in the Puget Sound region of Washington. Ultimate and maximum load transfer rates for design are correlated to geologic units and soil types found in the region. Variables such as pressure versus tremie grouting, hole diameter, soil density/consistency, and the presence of groundwater are compared to load transfer rates for similar geologic units and soil types. Results are also compared to published PTI, AASHTO, and FHWA guidelines. Our results indicate that published ranges may be conservative for some soil types in the Puget Sound region, especially for micropiles. Performing verification tests to failure instead of typical verification or performance tests is needed to improve correlations and provide less conservative design load transfer rates.

Jan 1, 2006

By Gary L. Seider, Dana A. Wesolek, Fred C. Schmednecht

"A new condominium project, The Atelier, developed by Pickus Companies located at the corner of Bryn Mawr and Sheridan in Chicago, IL required an earth retention system to protect the surrounding roads, alley, and existing neighboring apartment bui lding during its construction. Slurry Systems, Inc. (SSI) and Ground Engineering Consultants, Inc. designed the earth retention system using cantilevered sheet piling for three of the four sides: two sides bordering major streets and one side bordering an alley. For the fourth side, which borders an existing occupied brick building, a combination of sheet pil ing and AB. CHANCE® helical screw piers were used. SSI was actively involved in the review process of its earth retention system with the City of Chicago and quickly learned that there was no specific code for hel ical piers/anchors. (It appears that this is the case with most metropolitan cities throughout the United States). Consequently, the approval of underpinning for this project became the critical path, as much testing, calculations, meetings, and other details were required prior to its approval.SSI and AB. CHANCE® recognized that this process for underpinning approval must be seen by other contractors/suppliers who wish to use helical piers/anchors in the City of Chicago. Consequently, this project served as an opportunity to work with the City of Chicago and the City's Building Code Committee in furthering the development of the Helical Piers/Anchors Code, Section 1814. INTRODUCTION - HELICAL PIERSDefinition. A helical pier or anchor consists of one or more helix-shaped steel bearing plate(s) attached to a central steel stem (solid bar or pipe), which is installed by rotating or ""torquing"" into the ground. Each helix is attached near the tip, is circular in plan , and is formed into a screw thread with a defined pitch. Helical piers/anchors are pre-fabricated and can derive their load-carrying capacity through both end bearing and skin friction. The helical piers/anchors can be augmented with grout."

Jan 1, 2005

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Diego Bellato

Production data recorded by special foundation rigs during construction activities at the site are commonly used for quality assurance / quality control procedures and, in particular, to prove that the installed foundation elements comply with the geometrical and quality requirements defined in the design specifications. Parameters such as crowd force, penetration/withdrawal rate, rotational speed etc. are usually presented in reports in the form of depth and/or time profiles. This type of protocols are already standard QA/QC solutions for ground improvement methods like deep soil mixing or jet-grouting, but they are quite rarely applied in combination with other techniques like diaphragm walls or Kelly drilling. In the latter cases, one of the main reasons behind this lack of site documentation is related to the difficulty in interpreting huge amount of data collected during the creation of single elements, which, in some cases, can last several days (not always in a row). In addition, the building sequence is often characterized by many alternated operations involving different movements of the rig and the use of different tools. In this context, the identification of specific construction activities based only on the mere exam of the time profiles of the recorded production parameters is extremely difficult. In this paper, the time profiles of production parameters obtained from a fully-cased Kelly drilling rig employed on a site in Karlsruhe (Germany) have been investigated and compared with a detailed series of activities deduced from a video filmed during installation. Typical time profile patterns associated to specific procedures have been identified by combining the different information available. The outcome of this study helped project engineers to automatize the recognition of activities directly from production data and led to an overall understanding and optimization of the construction process. INTRODUCTION The special foundation industry is characterized by the use of highly sophisticated machinery for the realization of geotechnical systems such as piled rafts, retaining walls and slabs for excavation pits, cut-off walls for levees and embankments or ground improvement solutions. Rigs can vary in size, weight, and power and can be provided with several drilling tools to cope with the different soil conditions (e.g. clay, sand, rock) and the different geometries of the elements to be built at the site (e.g. micro-piles, large- diameter bored piles, diaphragm walls, anchors). Due to the challenging construction procedures, various types of sensors have started to be mounted on the equipment in the last decades to monitor the behavior of some important machine parameters and to inform rig operators about the on-going process and the status of their devices.

Jan 1, 2019

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By Waddah Akili

At an offshore site along the Red Sea coast of Saudi Arabia, marine structures were supported on tubular steel piles driven into coral and coral contaminated sands and silts. Surprises and disappointments faced during the installation of the piled foundation were, to a large measure, due to inappropriate design methodology and absence of proper soil information. The paper describes the design evolution process, highlights the static pile test program conducted to verify design parameters, and amplifies the need to prepare for worst possible scenario when coral deposits are encountered. Despite corrections made to the design, based on site-specific insitu parameters (skin friction, end bearing) perceived from load tests conducted on site; the final design adopted overestimated capacities in over 50 percent of total piles driven. The paper describes the changes introduced to the design during the execution of the project, highlights the pile test program conducted to verify the design, and compares pile design penetration with actual penetration depth. The unpredictable and erratic pile behavior observed, ascertains the need for more appropriate pile design and installation guidelines for driven piles in coral and coral contaminated formations.